1 files changed, 91 insertions, 0 deletions
diff --git a/board/keymile/pg-wcom-ls102xa/ddr.c b/board/keymile/pg-wcom-ls102xa/ddr.c
new file mode 100644
index 0000000..4ec60f1
--- /dev/null
+++ b/board/keymile/pg-wcom-ls102xa/ddr.c
@@ -0,0 +1,91 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ * Copyright 2020 Hitachi Power Grids. All rights reserved.
+ */
+
+#include <common.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
+#include <asm/io.h>
+#include <asm/arch/clock.h>
+#include <asm/global_data.h>
+#include <asm/arch/ls102xa_soc.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+			   dimm_params_t *pdimm,
+			   unsigned int ctrl_num)
+{
+	if (ctrl_num > 1) {
+		printf("Not supported controller number %d\n", ctrl_num);
+		return;
+	}
+
+	// 1/2 DRAM cycle (should be increased in case of ADDR/CMD heavily loaded than the clock)
+	popts->clk_adjust = 0x4;
+	popts->write_data_delay = 0x4;
+	// wr leveling start value for lane 0
+	popts->wrlvl_start = 0x5;
+	// wr leveling start values for lanes 1-3 (lane 4 not there)
+	popts->wrlvl_ctl_2 = 0x05050500;
+	// 32-bit DRAM, no need to set start values for lanes we do not have (5-8)
+	popts->wrlvl_ctl_3 = 0x0;
+	popts->cpo_override = 0x1f;
+
+	/* force DDR bus width to 32 bits */
+	popts->data_bus_width = 1;
+	popts->otf_burst_chop_en = 0;
+	popts->burst_length = DDR_BL8;
+
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 1;
+	/*
+	 * Write leveling override
+	 */
+	popts->wrlvl_override = 1;
+	popts->wrlvl_sample = 0xf;
+
+	/*
+	 * Rtt and Rtt_WR override
+	 */
+	popts->rtt_override = 0;
+
+	/* Enable ZQ calibration */
+	popts->zq_en = 1;
+
+	popts->cswl_override = DDR_CSWL_CS0;
+
+	/* optimize cpo for erratum A-009942 */
+	popts->cpo_sample = 0x58;
+
+	/* DHC_EN =1, ODT = 75 Ohm */
+	popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
+	popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
+}
+
+int fsl_initdram(void)
+{
+	phys_size_t dram_size;
+
+	puts("Initializing DDR....using SPD\n");
+	dram_size = fsl_ddr_sdram();
+
+	erratum_a008850_post();
+
+	gd->ram_size = dram_size;
+
+	return 0;
+}
+
+int dram_init_banksize(void)
+{
+	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+	gd->bd->bi_dram[0].size = gd->ram_size;
+
+	return 0;
+}