diff options
Diffstat (limited to 'board/dhelectronics/dh_imx8mp/spl.c')
-rw-r--r-- | board/dhelectronics/dh_imx8mp/spl.c | 187 |
1 files changed, 187 insertions, 0 deletions
diff --git a/board/dhelectronics/dh_imx8mp/spl.c b/board/dhelectronics/dh_imx8mp/spl.c new file mode 100644 index 0000000..312e4b9 --- /dev/null +++ b/board/dhelectronics/dh_imx8mp/spl.c @@ -0,0 +1,187 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2022 Marek Vasut <marex@denx.de> + */ + +#include <common.h> +#include <hang.h> +#include <image.h> +#include <init.h> +#include <spl.h> +#include <asm/io.h> +#include <asm-generic/gpio.h> +#include <asm/arch/clock.h> +#include <asm/arch/imx8mp_pins.h> +#include <asm/arch/sys_proto.h> +#include <asm/mach-imx/boot_mode.h> +#include <asm/arch/ddr.h> + +#include <dm/uclass.h> +#include <dm/device.h> +#include <dm/uclass-internal.h> +#include <dm/device-internal.h> + +#include <power/pmic.h> +#include <power/pca9450.h> + +#include "lpddr4_timing.h" + +DECLARE_GLOBAL_DATA_PTR; + +#define UART_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_FSEL1) +#define WDOG_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_ODE | PAD_CTL_PUE | PAD_CTL_PE) + +static const iomux_v3_cfg_t uart_pads[] = { + MX8MP_PAD_SAI2_RXFS__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL), + MX8MP_PAD_SAI2_RXC__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL), +}; + +static const iomux_v3_cfg_t wdog_pads[] = { + MX8MP_PAD_GPIO1_IO02__WDOG1_WDOG_B | MUX_PAD_CTRL(WDOG_PAD_CTRL), +}; + +static void dh_imx8mp_early_init_f(void) +{ + struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR; + + imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads)); + + set_wdog_reset(wdog); + + imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads)); +} + +static int dh_imx8mp_board_power_init(void) +{ + struct udevice *dev; + int ret; + + ret = pmic_get("pmic@25", &dev); + if (ret == -ENODEV) { + puts("Failed to get PMIC\n"); + return 0; + } + if (ret != 0) + return ret; + + /* BUCKxOUT_DVS0/1 control BUCK123 output. */ + pmic_reg_write(dev, PCA9450_BUCK123_DVS, 0x29); + + /* Increase VDD_SOC to typical value 0.95V before first DRAM access. */ + if (IS_ENABLED(CONFIG_IMX8M_VDD_SOC_850MV)) + /* Set DVS0 to 0.85V for special case. */ + pmic_reg_write(dev, PCA9450_BUCK1OUT_DVS0, 0x14); + else + pmic_reg_write(dev, PCA9450_BUCK1OUT_DVS0, 0x1c); + + /* Set DVS1 to 0.85v for suspend. */ + pmic_reg_write(dev, PCA9450_BUCK1OUT_DVS1, 0x14); + + /* + * Enable DVS control through PMIC_STBY_REQ and + * set B1_ENMODE=1 (ON by PMIC_ON_REQ=H). + */ + pmic_reg_write(dev, PCA9450_BUCK1CTRL, 0x59); + + /* Kernel uses OD/OD frequency for SoC. */ + + /* To avoid timing risk from SoC to ARM, increase VDD_ARM to OD voltage 0.95V */ + pmic_reg_write(dev, PCA9450_BUCK2OUT_DVS0, 0x1c); + + /* Set WDOG_B_CFG to cold reset. */ + pmic_reg_write(dev, PCA9450_RESET_CTRL, 0xA1); + + /* Set LDO4 and CONFIG2 to enable the I2C level translator. */ + pmic_reg_write(dev, PCA9450_LDO4CTRL, 0x59); + pmic_reg_write(dev, PCA9450_CONFIG2, 0x1); + + return 0; +} + +static struct dram_timing_info *dram_timing_info[8] = { + NULL, /* 512 MiB */ + NULL, /* 1024 MiB */ + NULL, /* 1536 MiB */ + NULL, /* 2048 MiB */ + NULL, /* 3072 MiB */ + &dh_imx8mp_dhcom_dram_timing_32g_x32, /* 4096 MiB */ + NULL, /* 6144 MiB */ + NULL, /* 8192 MiB */ +}; + +static void spl_dram_init(void) +{ + const u16 size[] = { 512, 1024, 1536, 2048, 3072, 4096, 6144, 8192 }; + u8 memcfg = dh_get_memcfg(); + int i; + + printf("DDR: %d MiB [0x%x]\n", size[memcfg], memcfg); + + if (!dram_timing_info[memcfg]) { + printf("Unsupported DRAM strapping, trying lowest supported. MEMCFG=0x%x\n", + memcfg); + for (i = 0; i < ARRAY_SIZE(dram_timing_info); i++) + if (dram_timing_info[i]) /* Configuration found */ + break; + } + + ddr_init(dram_timing_info[memcfg]); +} + +void spl_board_init(void) +{ + /* + * Set GIC clock to 500 MHz for OD VDD_SOC. Kernel driver does not + * allow to change it. Should set the clock after PMIC setting done. + * Default is 400 MHz (system_pll1_800m with div = 2) set by ROM for + * ND VDD_SOC. + */ + clock_enable(CCGR_GIC, 0); + clock_set_target_val(GIC_CLK_ROOT, CLK_ROOT_ON | CLK_ROOT_SOURCE_SEL(5)); + clock_enable(CCGR_GIC, 1); +} + +int spl_board_boot_device(enum boot_device boot_dev_spl) +{ + return BOOT_DEVICE_BOOTROM; +} + +void board_init_f(ulong dummy) +{ + struct udevice *dev; + int ret; + + arch_cpu_init(); + + init_uart_clk(0); + + dh_imx8mp_early_init_f(); + + preloader_console_init(); + + /* Clear the BSS. */ + memset(__bss_start, 0, __bss_end - __bss_start); + + ret = spl_early_init(); + if (ret) { + debug("spl_early_init() failed: %d\n", ret); + hang(); + } + + ret = uclass_get_device_by_name(UCLASS_CLK, + "clock-controller@30380000", + &dev); + if (ret < 0) { + printf("Failed to find clock node. Check device tree\n"); + hang(); + } + + enable_tzc380(); + + dh_imx8mp_board_power_init(); + + /* DDR initialization */ + spl_dram_init(); + + board_init_r(NULL, 0); +} |