diff options
Diffstat (limited to 'arch')
-rw-r--r-- | arch/arm/mach-mvebu/Kconfig | 22 | ||||
-rw-r--r-- | arch/arm/mach-mvebu/spl.c | 205 |
2 files changed, 205 insertions, 22 deletions
diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig index 12de6f1..89737a3 100644 --- a/arch/arm/mach-mvebu/Kconfig +++ b/arch/arm/mach-mvebu/Kconfig @@ -253,27 +253,27 @@ choice config MVEBU_SPL_BOOT_DEVICE_SPI bool "SPI NOR flash" imply ENV_IS_IN_SPI_FLASH - select SPL_DM_SPI - select SPL_SPI_FLASH_SUPPORT - select SPL_SPI_LOAD - select SPL_SPI_SUPPORT + imply SPL_DM_SPI + imply SPL_SPI_FLASH_SUPPORT + imply SPL_SPI_LOAD + imply SPL_SPI_SUPPORT select SPL_BOOTROM_SUPPORT config MVEBU_SPL_BOOT_DEVICE_MMC bool "SDIO/MMC card" imply ENV_IS_IN_MMC # GPIO needed for eMMC/SD card presence detection - select SPL_DM_GPIO - select SPL_DM_MMC - select SPL_GPIO - select SPL_LIBDISK_SUPPORT - select SPL_MMC_SUPPORT + imply SPL_DM_GPIO + imply SPL_DM_MMC + imply SPL_GPIO + imply SPL_LIBDISK_SUPPORT + imply SPL_MMC_SUPPORT select SPL_BOOTROM_SUPPORT config MVEBU_SPL_BOOT_DEVICE_SATA bool "SATA" - select SPL_SATA_SUPPORT - select SPL_LIBDISK_SUPPORT + imply SPL_SATA_SUPPORT + imply SPL_LIBDISK_SUPPORT select SPL_BOOTROM_SUPPORT config MVEBU_SPL_BOOT_DEVICE_UART diff --git a/arch/arm/mach-mvebu/spl.c b/arch/arm/mach-mvebu/spl.c index 5c3d959..3b6bc38 100644 --- a/arch/arm/mach-mvebu/spl.c +++ b/arch/arm/mach-mvebu/spl.c @@ -8,6 +8,7 @@ #include <debug_uart.h> #include <fdtdec.h> #include <hang.h> +#include <image.h> #include <init.h> #include <log.h> #include <spl.h> @@ -16,6 +17,160 @@ #include <asm/arch/cpu.h> #include <asm/arch/soc.h> +#if defined(CONFIG_SPL_SPI_FLASH_SUPPORT) || defined(CONFIG_SPL_MMC_SUPPORT) || defined(CONFIG_SPL_SATA_SUPPORT) + +/* + * When loading U-Boot via SPL from SPI NOR, CONFIG_SYS_SPI_U_BOOT_OFFS must + * point to the offset of kwbimage main header which is always at offset zero + * (defined by BootROM). Therefore other values of CONFIG_SYS_SPI_U_BOOT_OFFS + * makes U-Boot non-bootable. + */ +#ifdef CONFIG_SPL_SPI_FLASH_SUPPORT +#if defined(CONFIG_SYS_SPI_U_BOOT_OFFS) && CONFIG_SYS_SPI_U_BOOT_OFFS != 0 +#error CONFIG_SYS_SPI_U_BOOT_OFFS must be set to 0 +#endif +#endif + +/* + * When loading U-Boot via SPL from eMMC (in Marvell terminology SDIO), the + * kwbimage main header is stored at sector 0. U-Boot SPL needs to parse this + * header and figure out at which sector the U-Boot proper binary is stored. + * Partition booting is therefore not supported and CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR + * and CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_DATA_PART_OFFSET need to point to the + * kwbimage main header. + */ +#ifdef CONFIG_SPL_MMC_SUPPORT +#ifdef CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION +#error CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION is unsupported +#endif +#if defined(CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR) && CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR != 0 +#error CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR must be set to 0 +#endif +#if defined(CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_DATA_PART_OFFSET) && CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_DATA_PART_OFFSET != 0 +#error CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_DATA_PART_OFFSET must be set to 0 +#endif +#endif + +/* + * When loading U-Boot via SPL from SATA disk, the kwbimage main header is + * stored at sector 1. Therefore CONFIG_SPL_SATA_RAW_U_BOOT_SECTOR must be + * set to 1. Otherwise U-Boot SPL would not be able to load U-Boot proper. + */ +#ifdef CONFIG_SPL_SATA_SUPPORT +#if !defined(CONFIG_SPL_SATA_RAW_U_BOOT_USE_SECTOR) || !defined(CONFIG_SPL_SATA_RAW_U_BOOT_SECTOR) || CONFIG_SPL_SATA_RAW_U_BOOT_SECTOR != 1 +#error CONFIG_SPL_SATA_RAW_U_BOOT_SECTOR must be set to 1 +#endif +#endif + +/* Boot Type - block ID */ +#define IBR_HDR_I2C_ID 0x4D +#define IBR_HDR_SPI_ID 0x5A +#define IBR_HDR_NAND_ID 0x8B +#define IBR_HDR_SATA_ID 0x78 +#define IBR_HDR_PEX_ID 0x9C +#define IBR_HDR_UART_ID 0x69 +#define IBR_HDR_SDIO_ID 0xAE + +/* Structure of the main header, version 1 (Armada 370/38x/XP) */ +struct kwbimage_main_hdr_v1 { + uint8_t blockid; /* 0x0 */ + uint8_t flags; /* 0x1 */ + uint16_t reserved2; /* 0x2-0x3 */ + uint32_t blocksize; /* 0x4-0x7 */ + uint8_t version; /* 0x8 */ + uint8_t headersz_msb; /* 0x9 */ + uint16_t headersz_lsb; /* 0xA-0xB */ + uint32_t srcaddr; /* 0xC-0xF */ + uint32_t destaddr; /* 0x10-0x13 */ + uint32_t execaddr; /* 0x14-0x17 */ + uint8_t options; /* 0x18 */ + uint8_t nandblocksize; /* 0x19 */ + uint8_t nandbadblklocation; /* 0x1A */ + uint8_t reserved4; /* 0x1B */ + uint16_t reserved5; /* 0x1C-0x1D */ + uint8_t ext; /* 0x1E */ + uint8_t checksum; /* 0x1F */ +} __packed; + +#ifdef CONFIG_SPL_MMC_SUPPORT +u32 spl_mmc_boot_mode(const u32 boot_device) +{ + return MMCSD_MODE_RAW; +} +#endif + +int spl_parse_board_header(struct spl_image_info *spl_image, + const void *image_header, size_t size) +{ + const struct kwbimage_main_hdr_v1 *mhdr = image_header; + + if (size < sizeof(*mhdr)) { + /* This should be compile time assert */ + printf("FATAL ERROR: Image header size is too small\n"); + hang(); + } + + /* + * Very basic check for image validity. We cannot check mhdr->checksum + * as it is calculated also from variable length extended headers + * (including SPL content) which is not included in U-Boot image_header. + */ + if (mhdr->version != 1 || + ((mhdr->headersz_msb << 16) | mhdr->headersz_lsb) < sizeof(*mhdr) || + ( +#ifdef CONFIG_SPL_SPI_FLASH_SUPPORT + mhdr->blockid != IBR_HDR_SPI_ID && +#endif +#ifdef CONFIG_SPL_SATA_SUPPORT + mhdr->blockid != IBR_HDR_SATA_ID && +#endif +#ifdef CONFIG_SPL_MMC_SUPPORT + mhdr->blockid != IBR_HDR_SDIO_ID && +#endif + 1 + )) { + printf("ERROR: Not valid SPI/NAND/SATA/SDIO kwbimage v1\n"); + return -EINVAL; + } + + spl_image->offset = mhdr->srcaddr; + +#ifdef CONFIG_SPL_SATA_SUPPORT + /* + * For SATA srcaddr is specified in number of sectors. + * The main header is must be stored at sector number 1. + * This expects that sector size is 512 bytes and recalculates + * data offset to bytes relative to the main header. + */ + if (mhdr->blockid == IBR_HDR_SATA_ID) { + if (spl_image->offset < 1) { + printf("ERROR: Wrong SATA srcaddr in kwbimage\n"); + return -EINVAL; + } + spl_image->offset -= 1; + spl_image->offset *= 512; + } +#endif + +#ifdef CONFIG_SPL_MMC_SUPPORT + /* + * For SDIO (eMMC) srcaddr is specified in number of sectors. + * This expects that sector size is 512 bytes and recalculates + * data offset to bytes. + */ + if (mhdr->blockid == IBR_HDR_SDIO_ID) + spl_image->offset *= 512; +#endif + + spl_image->size = mhdr->blocksize; + spl_image->entry_point = mhdr->execaddr; + spl_image->load_addr = mhdr->destaddr; + spl_image->os = IH_OS_U_BOOT; + spl_image->name = "U-Boot"; + + return 0; +} + static u32 get_boot_device(void) { u32 val; @@ -49,11 +204,11 @@ static u32 get_boot_device(void) boot_device = (val & BOOT_DEV_SEL_MASK) >> BOOT_DEV_SEL_OFFS; debug("SAR_REG=0x%08x boot_device=0x%x\n", val, boot_device); switch (boot_device) { -#if defined(CONFIG_ARMADA_38X) +#ifdef BOOT_FROM_NAND case BOOT_FROM_NAND: return BOOT_DEVICE_NAND; #endif -#ifdef CONFIG_SPL_MMC_SUPPORT +#ifdef BOOT_FROM_MMC case BOOT_FROM_MMC: case BOOT_FROM_MMC_ALT: return BOOT_DEVICE_MMC1; @@ -69,15 +224,26 @@ static u32 get_boot_device(void) return BOOT_DEVICE_SATA; #endif case BOOT_FROM_SPI: - default: return BOOT_DEVICE_SPI; + default: + return BOOT_DEVICE_BOOTROM; }; } +#else + +static u32 get_boot_device(void) +{ + return BOOT_DEVICE_BOOTROM; +} + +#endif + u32 spl_boot_device(void) { u32 boot_device = get_boot_device(); + switch (boot_device) { /* * Return to the BootROM to continue the Marvell xmodem * UART boot protocol. As initiated by the kwboot tool. @@ -87,18 +253,35 @@ u32 spl_boot_device(void) * SPL has no chance to receive this information. So we * need to return to the BootROM to enable this xmodem * UART download. Use SPL infrastructure to return to BootROM. - * - * If booting from NAND lets let the BootROM load the - * rest of the bootloader. */ - switch (boot_device) { case BOOT_DEVICE_UART: -#if defined(CONFIG_ARMADA_38X) - case BOOT_DEVICE_NAND: -#endif return BOOT_DEVICE_BOOTROM; + + /* + * If SPL is compiled with chosen boot_device support + * then use SPL driver for loading U-Boot proper. + */ +#ifdef CONFIG_SPL_MMC_SUPPORT + case BOOT_DEVICE_MMC1: + return BOOT_DEVICE_MMC1; +#endif +#ifdef CONFIG_SPL_SATA_SUPPORT + case BOOT_FROM_SATA: + return BOOT_FROM_SATA; +#endif +#ifdef CONFIG_SPL_SPI_FLASH_SUPPORT + case BOOT_DEVICE_SPI: + return BOOT_DEVICE_SPI; +#endif + + /* + * If SPL is not compiled with chosen boot_device support + * then return to the BootROM. BootROM supports loading + * U-Boot proper from any valid boot_device present in SAR + * register. + */ default: - return boot_device; + return BOOT_DEVICE_BOOTROM; } } |