diff options
Diffstat (limited to 'arch/arm/dts/meson-g12b-odroid-n2.dtsi')
-rw-r--r-- | arch/arm/dts/meson-g12b-odroid-n2.dtsi | 74 |
1 files changed, 69 insertions, 5 deletions
diff --git a/arch/arm/dts/meson-g12b-odroid-n2.dtsi b/arch/arm/dts/meson-g12b-odroid-n2.dtsi index 6982632..344573e 100644 --- a/arch/arm/dts/meson-g12b-odroid-n2.dtsi +++ b/arch/arm/dts/meson-g12b-odroid-n2.dtsi @@ -13,6 +13,8 @@ aliases { serial0 = &uart_AO; ethernet0 = ðmac; + rtc0 = &rtc; + rtc1 = &vrtc; }; dioo2133: audio-amplifier-0 { @@ -40,7 +42,7 @@ leds { compatible = "gpio-leds"; - blue { + led-blue { label = "n2:blue"; gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; @@ -211,7 +213,7 @@ sound { compatible = "amlogic,axg-sound-card"; - model = "G12B-ODROID-N2"; + model = "ODROID-N2"; audio-widgets = "Line", "Lineout"; audio-aux-devs = <&tdmout_b>, <&tdmout_c>, <&tdmin_a>, <&tdmin_b>, <&tdmin_c>, <&tdmin_lb>, @@ -408,12 +410,12 @@ &ext_mdio { external_phy: ethernet-phy@0 { - /* Realtek RTL8211F (0x001cc916) */ + /* Realtek RTL8211F (0x001cc916) */ reg = <0>; max-speed = <1000>; reset-assert-us = <10000>; - reset-deassert-us = <30000>; + reset-deassert-us = <80000>; reset-gpios = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>; interrupt-parent = <&gpio_intc>; @@ -444,13 +446,58 @@ }; &gpio { + gpio-line-names = + /* GPIOZ */ + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + /* GPIOH */ + "", "", "", "", "", "", "", "", + "", + /* BOOT */ + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + /* GPIOC */ + "", "", "", "", "", "", "", "", + /* GPIOA */ + "PIN_44", /* GPIOA_0 */ + "PIN_46", /* GPIOA_1 */ + "PIN_45", /* GPIOA_2 */ + "PIN_47", /* GPIOA_3 */ + "PIN_26", /* GPIOA_4 */ + "", "", "", "", "", "", + "PIN_42", /* GPIOA_11 */ + "PIN_32", /* GPIOA_12 */ + "PIN_7", /* GPIOA_13 */ + "PIN_27", /* GPIOA_14 */ + "PIN_28", /* GPIOA_15 */ + /* GPIOX */ + "PIN_16", /* GPIOX_0 */ + "PIN_18", /* GPIOX_1 */ + "PIN_22", /* GPIOX_2 */ + "PIN_11", /* GPIOX_3 */ + "PIN_13", /* GPIOX_4 */ + "PIN_33", /* GPIOX_5 */ + "PIN_35", /* GPIOX_6 */ + "PIN_15", /* GPIOX_7 */ + "PIN_19", /* GPIOX_8 */ + "PIN_21", /* GPIOX_9 */ + "PIN_24", /* GPIOX_10 */ + "PIN_23", /* GPIOX_11 */ + "PIN_8", /* GPIOX_12 */ + "PIN_10", /* GPIOX_13 */ + "PIN_29", /* GPIOX_14 */ + "PIN_31", /* GPIOX_15 */ + "PIN_12", /* GPIOX_16 */ + "PIN_3", /* GPIOX_17 */ + "PIN_5", /* GPIOX_18 */ + "PIN_36"; /* GPIOX_19 */ /* * WARNING: The USB Hub on the Odroid-N2 needs a reset signal * to be turned high in order to be detected by the USB Controller * This signal should be handled by a USB specific power sequence * in order to reset the Hub when USB bus is powered down. */ - usb-hub { + hog-0 { gpio-hog; gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>; output-high; @@ -478,6 +525,18 @@ linux,rc-map-name = "rc-odroid"; }; +&i2c3 { + status = "okay"; + pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>; + pinctrl-names = "default"; + + rtc: rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + wakeup-source; + }; +}; + &pwm_ab { pinctrl-0 = <&pwm_a_e_pins>; pinctrl-names = "default"; @@ -494,6 +553,11 @@ status = "okay"; }; +&saradc { + status = "okay"; + vref-supply = <&vddao_1v8>; +}; + /* SD card */ &sd_emmc_b { status = "okay"; |