diff options
Diffstat (limited to 'README')
| -rw-r--r-- | README | 63 |
1 files changed, 55 insertions, 8 deletions
@@ -616,6 +616,14 @@ The following options need to be configured: boot loader that has already initialized the UART. Define this variable to flush the UART at init time. + CONFIG_SYS_NS16550_BROKEN_TEMT + + 16550 UART set the Transmitter Empty (TEMT) Bit when all output + has finished and the transmitter is totally empty. U-Boot waits + for this bit to be set to initialize the serial console. On some + broken platforms this bit is not set in SPL making U-Boot to + hang while waiting for TEMT. Define this option to avoid it. + - Console Interface: Depending on board, define exactly one serial port @@ -849,6 +857,7 @@ The following options need to be configured: CONFIG_CMD_LOADS loads CONFIG_CMD_MD5SUM print md5 message digest (requires CONFIG_CMD_MEMORY and CONFIG_MD5) + CONFIG_CMD_MEMINFO * Display detailed memory information CONFIG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base, loop, loopw, mtest CONFIG_CMD_MISC Misc functions like sleep etc @@ -1486,6 +1495,21 @@ CBFS (Coreboot Filesystem) support Normally display is black on white background; define CONFIG_SYS_WHITE_ON_BLACK to get it inverted. + CONFIG_LCD_ALIGNMENT + + Normally the LCD is page-aligned (tyically 4KB). If this is + defined then the LCD will be aligned to this value instead. + For ARM it is sometimes useful to use MMU_SECTION_SIZE + here, since it is cheaper to change data cache settings on + a per-section basis. + + CONFIG_CONSOLE_SCROLL_LINES + + When the console need to be scrolled, this is the number of + lines to scroll by. It defaults to 1. Increasing this makes + the console jump but can help speed up operation when scrolling + is slow. + CONFIG_LCD_BMP_RLE8 Support drawing of RLE8-compressed bitmaps on the LCD. @@ -1495,7 +1519,6 @@ CBFS (Coreboot Filesystem) support Enables an 'i2c edid' command which can read EDID information over I2C from an attached LCD display. - - Splash Screen Support: CONFIG_SPLASH_SCREEN If this option is set, the environment is checked for @@ -2364,6 +2387,15 @@ CBFS (Coreboot Filesystem) support run-time determined information about the hardware to the environment. These will be named board_name, board_rev. + CONFIG_DELAY_ENVIRONMENT + + Normally the environment is loaded when the board is + intialised so that it is available to U-Boot. This inhibits + that so that the environment is not available until + explicitly loaded later by U-Boot code. With CONFIG_OF_CONTROL + this is instead controlled by the value of + /config/load-environment. + - DataFlash Support: CONFIG_HAS_DATAFLASH @@ -2390,6 +2422,11 @@ CBFS (Coreboot Filesystem) support CONFIG_SF_DEFAULT_MODE (see include/spi.h) CONFIG_SF_DEFAULT_SPEED in Hz + CONFIG_CMD_SF_TEST + + Define this option to include a destructive SPI flash + test ('sf test'). + - SystemACE Support: CONFIG_SYSTEMACE @@ -2677,10 +2714,13 @@ FIT uImage format: CONFIG_FB_ADDR Define CONFIG_FB_ADDR if you want to use specific - address for frame buffer. - Then system will reserve the frame buffer address to - defined address instead of lcd_setmem (this function - grabs the memory for frame buffer by panel's size). + address for frame buffer. This is typically the case + when using a graphics controller has separate video + memory. U-Boot will then place the frame buffer at + the given address instead of dynamically reserving it + in system RAM by calling lcd_setmem(), which grabs + the memory for the frame buffer depending on the + configured panel size. Please see board_init_f function. @@ -2985,9 +3025,6 @@ Configuration Settings: non page size aligned address and this could cause major problems. -- CONFIG_SYS_TFTP_LOADADDR: - Default load address for network file downloads - - CONFIG_SYS_LOADS_BAUD_CHANGE: Enable temporary baudrate change while serial download @@ -3447,6 +3484,16 @@ use the "saveenv" command to store a valid environment. space for already greatly restricted images, including but not limited to NAND_SPL configurations. +- CONFIG_DISPLAY_BOARDINFO + Display information about the board that U-Boot is running on + when U-Boot starts up. The board function checkboard() is called + to do this. + +- CONFIG_DISPLAY_BOARDINFO_LATE + Similar to the previous option, but display this information + later, once stdio is running and output goes to the LCD, if + present. + Low Level (hardware related) configuration options: --------------------------------------------------- |