diff options
Diffstat (limited to 'README')
| -rw-r--r-- | README | 99 |
1 files changed, 36 insertions, 63 deletions
@@ -690,6 +690,14 @@ The following options need to be configured: exists, unlike the similar options in the Linux kernel. Do not set these options unless they apply! + COUNTER_FREQUENCY + Generic timer clock source frequency. + + COUNTER_FREQUENCY_REAL + Generic timer clock source frequency if the real clock is + different from COUNTER_FREQUENCY, and can only be determined + at run time. + NOTE: The following can be machine specific errata. These do have ability to provide rudimentary version and machine specific checks, but expect no product checks. @@ -1947,6 +1955,26 @@ CBFS (Coreboot Filesystem) support the console jump but can help speed up operation when scrolling is slow. + CONFIG_LCD_ROTATION + + Sometimes, for example if the display is mounted in portrait + mode or even if it's mounted landscape but rotated by 180degree, + we need to rotate our content of the display relative to the + framebuffer, so that user can read the messages which are + printed out. + Once CONFIG_LCD_ROTATION is defined, the lcd_console will be + initialized with a given rotation from "vl_rot" out of + "vidinfo_t" which is provided by the board specific code. + The value for vl_rot is coded as following (matching to + fbcon=rotate:<n> linux-kernel commandline): + 0 = no rotation respectively 0 degree + 1 = 90 degree rotation + 2 = 180 degree rotation + 3 = 270 degree rotation + + If CONFIG_LCD_ROTATION is not defined, the console will be + initialized with 0degree rotation. + CONFIG_LCD_BMP_RLE8 Support drawing of RLE8-compressed bitmaps on the LCD. @@ -2375,6 +2403,8 @@ CBFS (Coreboot Filesystem) support - define slave for bus 3 with CONFIG_SYS_MXC_I2C3_SLAVE If those defines are not set, default value is 100000 for speed, and 0 for slave. + - enable bus 3 with CONFIG_SYS_I2C_MXC_I2C3 + - enable bus 4 with CONFIG_SYS_I2C_MXC_I2C4 - drivers/i2c/rcar_i2c.c: - activate this driver with CONFIG_SYS_I2C_RCAR @@ -3066,17 +3096,6 @@ CBFS (Coreboot Filesystem) support memories can be connected with a given cs line. Currently Xilinx Zynq qspi supports these type of connections. - CONFIG_SYS_SPI_ST_ENABLE_WP_PIN - enable the W#/Vpp signal to disable writing to the status - register on ST MICRON flashes like the N25Q128. - The status register write enable/disable bit, combined with - the W#/VPP signal provides hardware data protection for the - device as follows: When the enable/disable bit is set to 1, - and the W#/VPP signal is driven LOW, the status register - nonvolatile bits become read-only and the WRITE STATUS REGISTER - operation will not execute. The only way to exit this - hardware-protected mode is to drive W#/VPP HIGH. - - SystemACE Support: CONFIG_SYSTEMACE @@ -3198,55 +3217,6 @@ CBFS (Coreboot Filesystem) support example, some LED's) on your board. At the moment, the following checkpoints are implemented: -- Detailed boot stage timing - CONFIG_BOOTSTAGE - Define this option to get detailed timing of each stage - of the boot process. - - CONFIG_BOOTSTAGE_USER_COUNT - This is the number of available user bootstage records. - Each time you call bootstage_mark(BOOTSTAGE_ID_ALLOC, ...) - a new ID will be allocated from this stash. If you exceed - the limit, recording will stop. - - CONFIG_BOOTSTAGE_REPORT - Define this to print a report before boot, similar to this: - - Timer summary in microseconds: - Mark Elapsed Stage - 0 0 reset - 3,575,678 3,575,678 board_init_f start - 3,575,695 17 arch_cpu_init A9 - 3,575,777 82 arch_cpu_init done - 3,659,598 83,821 board_init_r start - 3,910,375 250,777 main_loop - 29,916,167 26,005,792 bootm_start - 30,361,327 445,160 start_kernel - - CONFIG_CMD_BOOTSTAGE - Add a 'bootstage' command which supports printing a report - and un/stashing of bootstage data. - - CONFIG_BOOTSTAGE_FDT - Stash the bootstage information in the FDT. A root 'bootstage' - node is created with each bootstage id as a child. Each child - has a 'name' property and either 'mark' containing the - mark time in microsecond, or 'accum' containing the - accumulated time for that bootstage id in microseconds. - For example: - - bootstage { - 154 { - name = "board_init_f"; - mark = <3575678>; - }; - 170 { - name = "lcd"; - accum = <33482>; - }; - }; - - Code in the Linux kernel can find this in /proc/devicetree. Legacy uImage format: @@ -3340,9 +3310,9 @@ Legacy uImage format: 65 net/eth.c Ethernet found. -80 common/cmd_net.c usage wrong - 80 common/cmd_net.c before calling NetLoop() - -81 common/cmd_net.c some error in NetLoop() occurred - 81 common/cmd_net.c NetLoop() back without error + 80 common/cmd_net.c before calling net_loop() + -81 common/cmd_net.c some error in net_loop() occurred + 81 common/cmd_net.c net_loop() back without error -82 common/cmd_net.c size == 0 (File with size 0 loaded) 82 common/cmd_net.c trying automatic boot 83 common/cmd_net.c running "source" command @@ -4911,6 +4881,9 @@ Low Level (hardware related) configuration options: - CONFIG_FSL_DDR_SYNC_REFRESH Enable sync of refresh for multiple controllers. +- CONFIG_FSL_DDR_BIST + Enable built-in memory test for Freescale DDR controllers. + - CONFIG_SYS_83XX_DDR_USES_CS0 Only for 83xx systems. If specified, then DDR should be configured using CS0 and CS1 instead of CS2 and CS3. |