diff options
| -rw-r--r-- | README | 5 | ||||
| -rw-r--r-- | arch/mips/Kconfig | 23 | ||||
| -rw-r--r-- | arch/mips/cpu/start.S | 21 | ||||
| -rw-r--r-- | scripts/config_whitelist.txt | 1 |
4 files changed, 28 insertions, 22 deletions
@@ -542,11 +542,6 @@ The following options need to be configured: CONF_CM_CACHABLE_CUW CONF_CM_CACHABLE_ACCELERATED - CONFIG_SYS_XWAY_EBU_BOOTCFG - - Special option for Lantiq XWAY SoCs for booting from NOR flash. - See also arch/mips/cpu/mips32/start.S. - CONFIG_XWAY_SWAP_BYTES Enable compilation of tools/xway-swap-bytes needed for Lantiq diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig index 6e5e0ff..f71597f 100644 --- a/arch/mips/Kconfig +++ b/arch/mips/Kconfig @@ -28,6 +28,7 @@ config TARGET_MALTA select DM_SERIAL select DYNAMIC_IO_PORT_BASE select MIPS_CM + select MIPS_INSERT_BOOT_CONFIG select MIPS_L1_CACHE_SHIFT_6 select MIPS_L2_CACHE select OF_CONTROL @@ -390,6 +391,28 @@ config MIPS_CM wish U-Boot to configure it or make use of it to retrieve system information such as cache configuration. +config MIPS_INSERT_BOOT_CONFIG + bool + default n + help + Enable this to insert some board-specific boot configuration in + the U-Boot binary at offset 0x10. + +config MIPS_BOOT_CONFIG_WORD0 + hex + depends on MIPS_INSERT_BOOT_CONFIG + default 0x420 if TARGET_MALTA + default 0x0 + help + Value which is inserted as boot config word 0. + +config MIPS_BOOT_CONFIG_WORD1 + hex + depends on MIPS_INSERT_BOOT_CONFIG + default 0x0 + help + Value which is inserted as boot config word 1. + endif endmenu diff --git a/arch/mips/cpu/start.S b/arch/mips/cpu/start.S index 6ca0916..1d21b23 100644 --- a/arch/mips/cpu/start.S +++ b/arch/mips/cpu/start.S @@ -84,25 +84,14 @@ ENTRY(_start) b reset mtc0 zero, CP0_COUNT # clear cp0 count for most accurate boot timing -#if defined(CONFIG_SYS_XWAY_EBU_BOOTCFG) +#if defined(CONFIG_MIPS_INSERT_BOOT_CONFIG) /* - * Almost all Lantiq XWAY SoC devices have an external bus unit (EBU) to - * access external NOR flashes. If the board boots from NOR flash the - * internal BootROM does a blind read at address 0xB0000010 to read the - * initial configuration for that EBU in order to access the flash - * device with correct parameters. This config option is board-specific. + * Store some board-specific boot configuration. This is used by some + * MIPS systems like Malta. */ .org 0x10 - .word CONFIG_SYS_XWAY_EBU_BOOTCFG - .word 0x0 -#endif -#if defined(CONFIG_MALTA) - /* - * Linux expects the Board ID here. - */ - .org 0x10 - .word 0x00000420 # 0x420 (Malta Board with CoreLV) - .word 0x00000000 + .word CONFIG_MIPS_BOOT_CONFIG_WORD0 + .word CONFIG_MIPS_BOOT_CONFIG_WORD1 #endif #if defined(CONFIG_ROM_EXCEPTION_VECTORS) diff --git a/scripts/config_whitelist.txt b/scripts/config_whitelist.txt index 94953d8..15c1cc0 100644 --- a/scripts/config_whitelist.txt +++ b/scripts/config_whitelist.txt @@ -4421,7 +4421,6 @@ CONFIG_SYS_XHCI_USB1_ADDR CONFIG_SYS_XHCI_USB2_ADDR CONFIG_SYS_XHCI_USB3_ADDR CONFIG_SYS_XIMG_LEN -CONFIG_SYS_XWAY_EBU_BOOTCFG CONFIG_SYS_ZYNQ_QSPI_WAIT CONFIG_SYS_ZYNQ_SPI_WAIT CONFIG_SYS_i2C_FSL |