diff options
-rw-r--r-- | doc/device-tree-bindings/remoteproc/k3-rproc.txt | 50 | ||||
-rw-r--r-- | drivers/remoteproc/Kconfig | 9 | ||||
-rw-r--r-- | drivers/remoteproc/Makefile | 1 | ||||
-rw-r--r-- | drivers/remoteproc/k3_rproc.c | 244 |
4 files changed, 304 insertions, 0 deletions
diff --git a/doc/device-tree-bindings/remoteproc/k3-rproc.txt b/doc/device-tree-bindings/remoteproc/k3-rproc.txt new file mode 100644 index 0000000..0a1e858 --- /dev/null +++ b/doc/device-tree-bindings/remoteproc/k3-rproc.txt @@ -0,0 +1,50 @@ +Texas Instruments' K3 Remote processor driver +============================================= + +In K3 generation Socs, loading an image on any processing entity +cannot be done directly from U-Boot. In order to load an image, +remoteproc driver should communicate to SYSFW with a specific sequence. +Also enable the timer required for this remotecore. + +Required properties: +-------------------- +- compatible: Shall be: "ti,am654-rproc" +- reg: base address of the remoteproc timer. +- power-domains: Should contain two sets of entries: + First set corresponds to pm domain of the + remotecore timer. Seconf entry corresponds to the + remoteproc to start. + This property is as per the binding, + doc/device-tree-bindings/power/ti,sci-pm-domain.txt +- resets: Should contain a phandle to a reset controller node + and an args specifier containing the remote code + device id and reset mask value. This is as per the + doc/device-tree-bindings/reset/ti,sci-reset.txt +- ti,sci: Phandle to TI-SCI compatible System controller node. +- ti,sci-proc-id: Processor id as identified by TISCI + +Optional properties: +-------------------- +- assigned-clocks: Should contain a phandle to clock node and an args + specifier containing the remote core device id and + the clock id within the remote core. This is as per + doc/device-tree-bindings/clock/ti,sci-clk.txt +- assigned-clock-rates: One entry for each entry of assigned-clocks. This is + the frequency at which the corresponding clock needs + to be assigned. +- ti,sci-host-id: Host ID to which the processor control is transferred to + +Example: +--------- + +a53_0: a53@0 { + compatible = "ti,am654-rproc"; + power-domains = <&k3_pds 61>, + <&k3_pds 202>; + resets = <&k3_reset 202 0>; + assigned-clocks = <&k3_clks 202 0>; + assigned-clock-rates = <800000000>; + ti,sci = <&dmsc>; + ti,sci-proc-id = <32>; + ti,sci-host-id = <10>; +}; diff --git a/drivers/remoteproc/Kconfig b/drivers/remoteproc/Kconfig index 812d301..9eb532b 100644 --- a/drivers/remoteproc/Kconfig +++ b/drivers/remoteproc/Kconfig @@ -22,6 +22,15 @@ config K3_SYSTEM_CONTROLLER help Say 'y' here to add support for TI' K3 System Controller. +config REMOTEPROC_K3 + bool "Support for TI's K3 based remoteproc driver" + select REMOTEPROC + depends on DM + depends on ARCH_K3 + depends on OF_CONTROL + help + Say 'y' here to add support for TI' K3 remoteproc driver. + config REMOTEPROC_SANDBOX bool "Support for Test processor for Sandbox" select REMOTEPROC diff --git a/drivers/remoteproc/Makefile b/drivers/remoteproc/Makefile index bfd02ad..87ef9e6 100644 --- a/drivers/remoteproc/Makefile +++ b/drivers/remoteproc/Makefile @@ -8,5 +8,6 @@ obj-$(CONFIG_REMOTEPROC) += rproc-uclass.o # Remote proc drivers - Please keep this list alphabetically sorted. obj-$(CONFIG_K3_SYSTEM_CONTROLLER) += k3_system_controller.o +obj-$(CONFIG_REMOTEPROC_K3) += k3_rproc.o obj-$(CONFIG_REMOTEPROC_SANDBOX) += sandbox_testproc.o obj-$(CONFIG_REMOTEPROC_TI_POWER) += ti_power_proc.o diff --git a/drivers/remoteproc/k3_rproc.c b/drivers/remoteproc/k3_rproc.c new file mode 100644 index 0000000..3c29d92 --- /dev/null +++ b/drivers/remoteproc/k3_rproc.c @@ -0,0 +1,244 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Texas Instruments' K3 Remoteproc driver + * + * Copyright (C) 2018 Texas Instruments Incorporated - http://www.ti.com/ + * Lokesh Vutla <lokeshvutla@ti.com> + * + */ + +#include <common.h> +#include <dm.h> +#include <remoteproc.h> +#include <errno.h> +#include <clk.h> +#include <reset.h> +#include <asm/io.h> +#include <power-domain.h> +#include <linux/soc/ti/ti_sci_protocol.h> + +#define INVALID_ID 0xffff + +#define GTC_CNTCR_REG 0x0 +#define GTC_CNTR_EN 0x3 + +/** + * struct k3_rproc_privdata - Structure representing Remote processor data. + * @rproc_pwrdmn: rproc power domain data + * @rproc_rst: rproc reset control data + * @sci: Pointer to TISCI handle + * @gtc_base: Timer base address. + * @proc_id: TISCI processor ID + * @host_id: TISCI host id to which the processor gets assigned to. + */ +struct k3_rproc_privdata { + struct power_domain rproc_pwrdmn; + struct power_domain gtc_pwrdmn; + struct reset_ctl rproc_rst; + const struct ti_sci_handle *sci; + void *gtc_base; + u16 proc_id; + u16 host_id; +}; + +/** + * k3_rproc_load() - Load up the Remote processor image + * @dev: rproc device pointer + * @addr: Address at which image is available + * @size: size of the image + * + * Return: 0 if all goes good, else appropriate error message. + */ +static int k3_rproc_load(struct udevice *dev, ulong addr, ulong size) +{ + struct k3_rproc_privdata *rproc = dev_get_priv(dev); + const struct ti_sci_proc_ops *pops = &rproc->sci->ops.proc_ops; + int ret; + + dev_dbg(dev, "%s addr = 0x%lx, size = 0x%lx\n", __func__, addr, size); + + /* request for the processor */ + ret = pops->proc_request(rproc->sci, rproc->proc_id); + if (ret) { + dev_err(dev, "Requesting processor failed %d\n", ret); + return ret; + } + + ret = pops->set_proc_boot_cfg(rproc->sci, rproc->proc_id, addr, 0, 0); + if (ret) { + dev_err(dev, "set_proc_boot_cfg failed %d\n", ret); + return ret; + } + + dev_dbg(dev, "%s: rproc successfully loaded\n", __func__); + + return 0; +} + +/** + * k3_rproc_start() - Start the remote processor + * @dev: rproc device pointer + * + * Return: 0 if all went ok, else return appropriate error + */ +static int k3_rproc_start(struct udevice *dev) +{ + struct k3_rproc_privdata *rproc = dev_get_priv(dev); + const struct ti_sci_proc_ops *pops = &rproc->sci->ops.proc_ops; + int ret; + + dev_dbg(dev, "%s\n", __func__); + + ret = power_domain_on(&rproc->gtc_pwrdmn); + if (ret) { + dev_err(dev, "power_domain_on() failed: %d\n", ret); + return ret; + } + + /* Enable the timer before starting remote core */ + writel(GTC_CNTR_EN, rproc->gtc_base + GTC_CNTCR_REG); + + /* + * Setting the right clock frequency would have taken care by + * assigned-clock-rates during the device probe. So no need to + * set the frequency again here. + */ + ret = power_domain_on(&rproc->rproc_pwrdmn); + if (ret) { + dev_err(dev, "power_domain_on() failed: %d\n", ret); + return ret; + } + + if (rproc->host_id != INVALID_ID) { + ret = pops->proc_handover(rproc->sci, rproc->proc_id, + rproc->host_id); + if (ret) { + dev_err(dev, "Handover processor failed %d\n", ret); + return ret; + } + } else { + ret = pops->proc_release(rproc->sci, rproc->proc_id); + if (ret) { + dev_err(dev, "Processor release failed %d\n", ret); + return ret; + } + } + + dev_dbg(dev, "%s: rproc successfully started\n", __func__); + + return 0; +} + +/** + * k3_rproc_init() - Initialize the remote processor + * @dev: rproc device pointer + * + * Return: 0 if all went ok, else return appropriate error + */ +static int k3_rproc_init(struct udevice *dev) +{ + dev_dbg(dev, "%s\n", __func__); + + /* Enable the module */ + dev_dbg(dev, "%s: rproc successfully initialized\n", __func__); + + return 0; +} + +static const struct dm_rproc_ops k3_rproc_ops = { + .init = k3_rproc_init, + .load = k3_rproc_load, + .start = k3_rproc_start, +}; + +/** + * k3_of_to_priv() - generate private data from device tree + * @dev: corresponding k3 remote processor device + * @priv: pointer to driver specific private data + * + * Return: 0 if all goes good, else appropriate error message. + */ +static int k3_rproc_of_to_priv(struct udevice *dev, + struct k3_rproc_privdata *rproc) +{ + int ret; + + dev_dbg(dev, "%s\n", __func__); + + ret = power_domain_get_by_index(dev, &rproc->rproc_pwrdmn, 1); + if (ret) { + dev_err(dev, "power_domain_get() failed: %d\n", ret); + return ret; + } + + ret = power_domain_get_by_index(dev, &rproc->gtc_pwrdmn, 0); + if (ret) { + dev_err(dev, "power_domain_get() failed: %d\n", ret); + return ret; + } + + ret = reset_get_by_index(dev, 0, &rproc->rproc_rst); + if (ret) { + dev_err(dev, "reset_get() failed: %d\n", ret); + return ret; + } + + rproc->sci = ti_sci_get_by_phandle(dev, "ti,sci"); + if (IS_ERR(rproc->sci)) { + dev_err(dev, "ti_sci get failed: %d\n", ret); + return PTR_ERR(rproc->sci); + } + + rproc->gtc_base = dev_read_addr_ptr(dev); + if (!rproc->gtc_base) { + dev_err(dev, "Get address failed\n"); + return -ENODEV; + } + + rproc->proc_id = dev_read_u32_default(dev, "ti,sci-proc-id", + INVALID_ID); + rproc->host_id = dev_read_u32_default(dev, "ti,sci-host-id", + INVALID_ID); + + return 0; +} + +/** + * k3_rproc_probe() - Basic probe + * @dev: corresponding k3 remote processor device + * + * Return: 0 if all goes good, else appropriate error message. + */ +static int k3_rproc_probe(struct udevice *dev) +{ + struct k3_rproc_privdata *priv; + int ret; + + dev_dbg(dev, "%s\n", __func__); + + priv = dev_get_priv(dev); + + ret = k3_rproc_of_to_priv(dev, priv); + if (ret) { + dev_dbg(dev, "%s: Probe failed with error %d\n", __func__, ret); + return ret; + } + + dev_dbg(dev, "Remoteproc successfully probed\n"); + + return 0; +} + +static const struct udevice_id k3_rproc_ids[] = { + { .compatible = "ti,am654-rproc"}, + {} +}; + +U_BOOT_DRIVER(k3_rproc) = { + .name = "k3_rproc", + .of_match = k3_rproc_ids, + .id = UCLASS_REMOTEPROC, + .ops = &k3_rproc_ops, + .probe = k3_rproc_probe, + .priv_auto_alloc_size = sizeof(struct k3_rproc_privdata), +}; |