diff options
61 files changed, 983 insertions, 91 deletions
diff --git a/arch/arm/cpu/arm720t/tegra-common/cpu.c b/arch/arm/cpu/arm720t/tegra-common/cpu.c index 2c5cd63..168f525 100644 --- a/arch/arm/cpu/arm720t/tegra-common/cpu.c +++ b/arch/arm/cpu/arm720t/tegra-common/cpu.c @@ -378,8 +378,7 @@ void clock_enable_coresight(int enable) void halt_avp(void) { for (;;) { - writel((HALT_COP_EVENT_JTAG | HALT_COP_EVENT_IRQ_1 \ - | HALT_COP_EVENT_FIQ_1 | (FLOW_MODE_STOP<<29)), - FLOW_CTLR_HALT_COP_EVENTS); + writel(HALT_COP_EVENT_JTAG | (FLOW_MODE_STOP << 29), + FLOW_CTLR_HALT_COP_EVENTS); } } diff --git a/arch/arm/cpu/arm720t/tegra124/cpu.c b/arch/arm/cpu/arm720t/tegra124/cpu.c index c03aaf1..97f5928 100644 --- a/arch/arm/cpu/arm720t/tegra124/cpu.c +++ b/arch/arm/cpu/arm720t/tegra124/cpu.c @@ -252,8 +252,8 @@ void start_cpu(u32 reset_vector) tegra124_init_clocks(); /* Set power-gating timer multiplier */ - clrbits_le32(&pmc->pmc_pwrgate_timer_mult, TIMER_MULT_MASK); - setbits_le32(&pmc->pmc_pwrgate_timer_mult, MULT_8); + writel((MULT_8 << TIMER_MULT_SHIFT) | (MULT_8 << TIMER_MULT_CPU_SHIFT), + &pmc->pmc_pwrgate_timer_mult); enable_cpu_power_rail(); enable_cpu_clocks(); diff --git a/arch/arm/cpu/arm926ejs/at91/at91sam9263_devices.c b/arch/arm/cpu/arm926ejs/at91/at91sam9263_devices.c index 99a3913..6b51d5f 100644 --- a/arch/arm/cpu/arm926ejs/at91/at91sam9263_devices.c +++ b/arch/arm/cpu/arm926ejs/at91/at91sam9263_devices.c @@ -143,6 +143,31 @@ void at91_spi1_hw_init(unsigned long cs_mask) } #endif +#if defined(CONFIG_GENERIC_ATMEL_MCI) +void at91_mci_hw_init(void) +{ + /* Enable mci clock */ + struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; + writel(1 << ATMEL_ID_MCI1, &pmc->pcer); + + at91_set_a_periph(AT91_PIO_PORTA, 6, PUP); /* MCI1_CK */ + +#if defined(CONFIG_ATMEL_MCI_PORTB) + at91_set_a_periph(AT91_PIO_PORTA, 21, PUP); /* MCI1_CDB */ + at91_set_a_periph(AT91_PIO_PORTA, 22, PUP); /* MCI1_DB0 */ + at91_set_a_periph(AT91_PIO_PORTA, 23, PUP); /* MCI1_DB1 */ + at91_set_a_periph(AT91_PIO_PORTA, 24, PUP); /* MCI1_DB2 */ + at91_set_a_periph(AT91_PIO_PORTA, 25, PUP); /* MCI1_DB3 */ +#else + at91_set_a_periph(AT91_PIO_PORTA, 7, PUP); /* MCI1_CDA */ + at91_set_a_periph(AT91_PIO_PORTA, 8, PUP); /* MCI1_DA0 */ + at91_set_a_periph(AT91_PIO_PORTA, 9, PUP); /* MCI1_DA1 */ + at91_set_a_periph(AT91_PIO_PORTA, 10, PUP); /* MCI1_DA2 */ + at91_set_a_periph(AT91_PIO_PORTA, 11, PUP); /* MCI1_DA3 */ +#endif +} +#endif + #ifdef CONFIG_MACB void at91_macb_hw_init(void) { diff --git a/arch/arm/cpu/armv7/am33xx/clock_am43xx.c b/arch/arm/cpu/armv7/am33xx/clock_am43xx.c index 57f5949..d0bc234 100644 --- a/arch/arm/cpu/armv7/am33xx/clock_am43xx.c +++ b/arch/arm/cpu/armv7/am33xx/clock_am43xx.c @@ -97,6 +97,7 @@ void enable_basic_clocks(void) &cmper->gpio4clkctrl, &cmper->gpio5clkctrl, &cmper->i2c1clkctrl, + &cmper->cpgmac0clkctrl, &cmper->emiffwclkctrl, &cmper->emifclkctrl, &cmper->otfaemifclkctrl, diff --git a/arch/arm/cpu/armv7/am33xx/ddr.c b/arch/arm/cpu/armv7/am33xx/ddr.c index d05e666..9a625c4 100644 --- a/arch/arm/cpu/armv7/am33xx/ddr.c +++ b/arch/arm/cpu/armv7/am33xx/ddr.c @@ -80,8 +80,8 @@ static void configure_mr(int nr, u32 cs) */ void config_sdram_emif4d5(const struct emif_regs *regs, int nr) { - writel(0x0, &emif_reg[nr]->emif_pwr_mgmt_ctrl); - writel(0x0, &emif_reg[nr]->emif_pwr_mgmt_ctrl_shdw); + writel(0xA0, &emif_reg[nr]->emif_pwr_mgmt_ctrl); + writel(0xA0, &emif_reg[nr]->emif_pwr_mgmt_ctrl_shdw); writel(0x1, &emif_reg[nr]->emif_iodft_tlgc); writel(regs->zq_config, &emif_reg[nr]->emif_zq_config); @@ -96,6 +96,7 @@ void config_sdram_emif4d5(const struct emif_regs *regs, int nr) writel(regs->ref_ctrl, &emif_reg[nr]->emif_sdram_ref_ctrl); writel(regs->sdram_config, &emif_reg[nr]->emif_sdram_config); + writel(regs->sdram_config, &cstat->secure_emif_sdram_config); if (emif_sdram_type() == EMIF_SDRAM_TYPE_LPDDR2) { configure_mr(nr, 0); diff --git a/arch/arm/cpu/armv7/am33xx/emif4.c b/arch/arm/cpu/armv7/am33xx/emif4.c index d28fceb..3e39752 100644 --- a/arch/arm/cpu/armv7/am33xx/emif4.c +++ b/arch/arm/cpu/armv7/am33xx/emif4.c @@ -113,7 +113,7 @@ void config_ddr(unsigned int pll, const struct ctrl_ioregs *ioregs, writel(readl(&cm_device->cm_dll_ctrl) & ~0x1, &cm_device->cm_dll_ctrl); while ((readl(&cm_device->cm_dll_ctrl) && CM_DLL_READYST) == 0) ; - writel(0x0, &ddrctrl->ddrioctrl); + writel(0x80000000, &ddrctrl->ddrioctrl); config_io_ctrl(ioregs); diff --git a/arch/arm/cpu/at91-common/spl.c b/arch/arm/cpu/at91-common/spl.c index 37c0cc4..7f4debb 100644 --- a/arch/arm/cpu/at91-common/spl.c +++ b/arch/arm/cpu/at91-common/spl.c @@ -52,6 +52,10 @@ u32 spl_boot_device(void) { #ifdef CONFIG_SYS_USE_MMC return BOOT_DEVICE_MMC1; +#elif CONFIG_SYS_USE_NANDFLASH + return BOOT_DEVICE_NAND; +#elif CONFIG_SYS_USE_SERIALFLASH + return BOOT_DEVICE_SPI; #endif return BOOT_DEVICE_NONE; } diff --git a/arch/arm/include/asm/arch-at91/gpio.h b/arch/arm/include/asm/arch-at91/gpio.h index ff6142b..7121388 100644 --- a/arch/arm/include/asm/arch-at91/gpio.h +++ b/arch/arm/include/asm/arch-at91/gpio.h @@ -214,7 +214,7 @@ static inline unsigned pin_to_mask(unsigned pin) /* The following macros are need for backward compatibility */ #define at91_set_GPIO_periph(x, y) \ - at91_set_gpio_periph((x - PIN_BASE) / 32,(x % 32), y) + at91_set_pio_periph((x - PIN_BASE) / 32,(x % 32), y) #define at91_set_A_periph(x, y) \ at91_set_a_periph((x - PIN_BASE) / 32,(x % 32), y) #define at91_set_B_periph(x, y) \ diff --git a/arch/arm/include/asm/arch-at91/spl.h b/arch/arm/include/asm/arch-at91/spl.h index 68c5349..d8a87da 100644 --- a/arch/arm/include/asm/arch-at91/spl.h +++ b/arch/arm/include/asm/arch-at91/spl.h @@ -14,6 +14,10 @@ enum { BOOT_DEVICE_MMC1, BOOT_DEVICE_MMC2, BOOT_DEVICE_MMC2_2, +#elif CONFIG_SYS_USE_NANDFLASH + BOOT_DEVICE_NAND, +#elif CONFIG_SYS_USE_SERIALFLASH + BOOT_DEVICE_SPI, #endif }; diff --git a/arch/arm/include/asm/arch-tegra/pmc.h b/arch/arm/include/asm/arch-tegra/pmc.h index 4c3264b..1dd3154 100644 --- a/arch/arm/include/asm/arch-tegra/pmc.h +++ b/arch/arm/include/asm/arch-tegra/pmc.h @@ -298,14 +298,25 @@ struct pmc_ctlr { #define PMC_XOFS_SHIFT 1 #define PMC_XOFS_MASK (0x3F << PMC_XOFS_SHIFT) +#if defined(CONFIG_TEGRA114) #define TIMER_MULT_SHIFT 0 #define TIMER_MULT_MASK (3 << TIMER_MULT_SHIFT) #define TIMER_MULT_CPU_SHIFT 2 #define TIMER_MULT_CPU_MASK (3 << TIMER_MULT_CPU_SHIFT) +#elif defined(CONFIG_TEGRA124) +#define TIMER_MULT_SHIFT 0 +#define TIMER_MULT_MASK (7 << TIMER_MULT_SHIFT) +#define TIMER_MULT_CPU_SHIFT 3 +#define TIMER_MULT_CPU_MASK (7 << TIMER_MULT_CPU_SHIFT) +#endif + #define MULT_1 0 #define MULT_2 1 #define MULT_4 2 #define MULT_8 3 +#if defined(CONFIG_TEGRA124) +#define MULT_16 4 +#endif #define AMAP_WRITE_SHIFT 20 #define AMAP_WRITE_ON (1 << AMAP_WRITE_SHIFT) diff --git a/arch/arm/include/asm/arch-tegra/tegra.h b/arch/arm/include/asm/arch-tegra/tegra.h index 5fe19ae..d63af0e 100644 --- a/arch/arm/include/asm/arch-tegra/tegra.h +++ b/arch/arm/include/asm/arch-tegra/tegra.h @@ -34,7 +34,12 @@ #define NV_PA_PMC_BASE (NV_PA_APB_MISC_BASE + 0xE400) #define NV_PA_EMC_BASE (NV_PA_APB_MISC_BASE + 0xF400) #define NV_PA_FUSE_BASE (NV_PA_APB_MISC_BASE + 0xF800) +#if defined(CONFIG_TEGRA20) || defined(CONFIG_TEGRA30) || \ + defined(CONFIG_TEGRA114) #define NV_PA_CSITE_BASE 0x70040000 +#else +#define NV_PA_CSITE_BASE 0x70800000 +#endif #define TEGRA_USB_ADDR_MASK 0xFFFFC000 #define NV_PA_SDRC_CS0 NV_PA_SDRAM_BASE diff --git a/arch/arm/include/asm/arch-tegra114/tegra.h b/arch/arm/include/asm/arch-tegra114/tegra.h index 5d426b5..705ca57 100644 --- a/arch/arm/include/asm/arch-tegra114/tegra.h +++ b/arch/arm/include/asm/arch-tegra114/tegra.h @@ -17,6 +17,8 @@ #ifndef _TEGRA114_H_ #define _TEGRA114_H_ +#define CONFIG_TEGRA114 + #define NV_PA_SDRAM_BASE 0x80000000 /* 0x80000000 for real T114 */ #define NV_PA_TSC_BASE 0x700F0000 /* System Counter TSC regs */ diff --git a/arch/arm/include/asm/arch-tegra124/tegra.h b/arch/arm/include/asm/arch-tegra124/tegra.h index db3d837..86ebd19 100644 --- a/arch/arm/include/asm/arch-tegra124/tegra.h +++ b/arch/arm/include/asm/arch-tegra124/tegra.h @@ -8,6 +8,8 @@ #ifndef _TEGRA124_H_ #define _TEGRA124_H_ +#define CONFIG_TEGRA124 + #define NV_PA_SDRAM_BASE 0x80000000 #define NV_PA_TSC_BASE 0x700F0000 /* System Counter TSC regs */ #define NV_PA_MC_BASE 0x70019000 /* Mem Ctlr regs (MCB, etc.) */ diff --git a/arch/arm/include/asm/arch-tegra20/tegra.h b/arch/arm/include/asm/arch-tegra20/tegra.h index 18856ac..6a4b40e 100644 --- a/arch/arm/include/asm/arch-tegra20/tegra.h +++ b/arch/arm/include/asm/arch-tegra20/tegra.h @@ -8,6 +8,8 @@ #ifndef _TEGRA20_H_ #define _TEGRA20_H_ +#define CONFIG_TEGRA20 + #define NV_PA_SDRAM_BASE 0x00000000 #include <asm/arch-tegra/tegra.h> diff --git a/arch/arm/include/asm/arch-tegra30/tegra.h b/arch/arm/include/asm/arch-tegra30/tegra.h index c02c5d8..4ad8b1c 100644 --- a/arch/arm/include/asm/arch-tegra30/tegra.h +++ b/arch/arm/include/asm/arch-tegra30/tegra.h @@ -17,6 +17,8 @@ #ifndef _TEGRA30_H_ #define _TEGRA30_H_ +#define CONFIG_TEGRA30 + #define NV_PA_SDRAM_BASE 0x80000000 /* 0x80000000 for real T30 */ #include <asm/arch-tegra/tegra.h> diff --git a/board/BuR/common/common.c b/board/BuR/common/common.c index 6d187ea..4c926ce 100644 --- a/board/BuR/common/common.c +++ b/board/BuR/common/common.c @@ -141,12 +141,12 @@ static struct cpsw_slave_data cpsw_slaves[] = { { .slave_reg_ofs = 0x208, .sliver_reg_ofs = 0xd80, - .phy_id = 0, + .phy_addr = 1, }, { .slave_reg_ofs = 0x308, .sliver_reg_ofs = 0xdc0, - .phy_id = 1, + .phy_addr = 2, }, }; diff --git a/board/atmel/at91sam9263ek/at91sam9263ek.c b/board/atmel/at91sam9263ek/at91sam9263ek.c index 7784cd7..db29879 100644 --- a/board/atmel/at91sam9263ek/at91sam9263ek.c +++ b/board/atmel/at91sam9263ek/at91sam9263ek.c @@ -24,6 +24,7 @@ #include <net.h> #endif #include <netdev.h> +#include <atmel_mci.h> DECLARE_GLOBAL_DATA_PTR; @@ -214,6 +215,15 @@ void lcd_show_board_info(void) #endif /* CONFIG_LCD_INFO */ #endif +#ifdef CONFIG_GENERIC_ATMEL_MCI +int board_mmc_init(bd_t *bd) +{ + at91_mci_hw_init(); + + return atmel_mci_init((void *)ATMEL_BASE_MCI1); +} +#endif + int board_early_init_f(void) { struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; diff --git a/board/atmel/sama5d3_xplained/Makefile b/board/atmel/sama5d3_xplained/Makefile new file mode 100644 index 0000000..ec82b06 --- /dev/null +++ b/board/atmel/sama5d3_xplained/Makefile @@ -0,0 +1,15 @@ +# +# (C) Copyright 2003-2008 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# (C) Copyright 2008 +# Stelian Pop <stelian@popies.net> +# Lead Tech Design <www.leadtechdesign.com> +# +# (C) Copyright 2014 +# Bo Shen <voice.shen@atmel.com> +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += sama5d3_xplained.o diff --git a/board/atmel/sama5d3_xplained/sama5d3_xplained.c b/board/atmel/sama5d3_xplained/sama5d3_xplained.c new file mode 100644 index 0000000..39f2dc6 --- /dev/null +++ b/board/atmel/sama5d3_xplained/sama5d3_xplained.c @@ -0,0 +1,130 @@ +/* + * Copyright (C) 2014 Atmel Corporation + * Bo Shen <voice.shen@atmel.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <mmc.h> +#include <asm/io.h> +#include <asm/arch/sama5d3_smc.h> +#include <asm/arch/at91_common.h> +#include <asm/arch/at91_pmc.h> +#include <asm/arch/at91_rstc.h> +#include <asm/arch/gpio.h> +#include <asm/arch/clk.h> +#include <atmel_mci.h> +#include <net.h> +#include <netdev.h> + +DECLARE_GLOBAL_DATA_PTR; + +#ifdef CONFIG_NAND_ATMEL +void sama5d3_xplained_nand_hw_init(void) +{ + struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC; + + at91_periph_clk_enable(ATMEL_ID_SMC); + + /* Configure SMC CS3 for NAND/SmartMedia */ + writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(1) | + AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(1), + &smc->cs[3].setup); + writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(5) | + AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(5), + &smc->cs[3].pulse); + writel(AT91_SMC_CYCLE_NWE(8) | AT91_SMC_CYCLE_NRD(8), + &smc->cs[3].cycle); + writel(AT91_SMC_TIMINGS_TCLR(3) | AT91_SMC_TIMINGS_TADL(10) | + AT91_SMC_TIMINGS_TAR(3) | AT91_SMC_TIMINGS_TRR(4) | + AT91_SMC_TIMINGS_TWB(5) | AT91_SMC_TIMINGS_RBNSEL(3)| + AT91_SMC_TIMINGS_NFSEL(1), &smc->cs[3].timings); + writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | + AT91_SMC_MODE_EXNW_DISABLE | +#ifdef CONFIG_SYS_NAND_DBW_16 + AT91_SMC_MODE_DBW_16 | +#else /* CONFIG_SYS_NAND_DBW_8 */ + AT91_SMC_MODE_DBW_8 | +#endif + AT91_SMC_MODE_TDF_CYCLE(3), + &smc->cs[3].mode); +} +#endif + +#ifdef CONFIG_CMD_USB +static void sama5d3_xplained_usb_hw_init(void) +{ + at91_set_pio_output(AT91_PIO_PORTE, 3, 0); + at91_set_pio_output(AT91_PIO_PORTE, 4, 0); +} +#endif + +#ifdef CONFIG_GENERIC_ATMEL_MCI +static void sama5d3_xplained_mci0_hw_init(void) +{ + at91_mci_hw_init(); + + at91_set_pio_output(AT91_PIO_PORTE, 2, 0); /* MCI0 Power */ +} +#endif + +int board_early_init_f(void) +{ + at91_periph_clk_enable(ATMEL_ID_PIOA); + at91_periph_clk_enable(ATMEL_ID_PIOB); + at91_periph_clk_enable(ATMEL_ID_PIOC); + at91_periph_clk_enable(ATMEL_ID_PIOD); + at91_periph_clk_enable(ATMEL_ID_PIOE); + + at91_seriald_hw_init(); + + return 0; +} + +int board_init(void) +{ + /* adress of boot parameters */ + gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; + +#ifdef CONFIG_NAND_ATMEL + sama5d3_xplained_nand_hw_init(); +#endif +#ifdef CONFIG_CMD_USB + sama5d3_xplained_usb_hw_init(); +#endif +#ifdef CONFIG_GENERIC_ATMEL_MCI + sama5d3_xplained_mci0_hw_init(); +#endif +#ifdef CONFIG_MACB + at91_gmac_hw_init(); + at91_macb_hw_init(); +#endif + return 0; +} + +int dram_init(void) +{ + gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE, + CONFIG_SYS_SDRAM_SIZE); + + return 0; +} + +int board_eth_init(bd_t *bis) +{ +#ifdef CONFIG_MACB + macb_eth_initialize(0, (void *)ATMEL_BASE_GMAC, 0x00); + macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC, 0x00); +#endif + return 0; +} + +#ifdef CONFIG_GENERIC_ATMEL_MCI +int board_mmc_init(bd_t *bis) +{ + atmel_mci_init((void *)ATMEL_BASE_MCI0); + + return 0; +} +#endif diff --git a/board/atmel/sama5d3xek/sama5d3xek.c b/board/atmel/sama5d3xek/sama5d3xek.c index eff94a4..c835c12 100644 --- a/board/atmel/sama5d3xek/sama5d3xek.c +++ b/board/atmel/sama5d3xek/sama5d3xek.c @@ -307,6 +307,10 @@ void spl_board_init(void) { #ifdef CONFIG_SYS_USE_MMC sama5d3xek_mci_hw_init(); +#elif CONFIG_SYS_USE_NANDFLASH + sama5d3xek_nand_hw_init(); +#elif CONFIG_SYS_USE_SERIALFLASH + at91_spi0_hw_init(1 << 0); #endif } diff --git a/board/compulab/cm_t335/cm_t335.c b/board/compulab/cm_t335/cm_t335.c index 01019e8..9583149 100644 --- a/board/compulab/cm_t335/cm_t335.c +++ b/board/compulab/cm_t335/cm_t335.c @@ -47,7 +47,7 @@ static void cpsw_control(int enabled) static struct cpsw_slave_data cpsw_slave = { .slave_reg_ofs = 0x208, .sliver_reg_ofs = 0xd80, - .phy_id = 0, + .phy_addr = 0, .phy_if = PHY_INTERFACE_MODE_RGMII, }; diff --git a/board/isee/igep0033/board.c b/board/isee/igep0033/board.c index 089a835..9f8fcf2 100644 --- a/board/isee/igep0033/board.c +++ b/board/isee/igep0033/board.c @@ -116,7 +116,7 @@ static struct cpsw_slave_data cpsw_slaves[] = { { .slave_reg_ofs = 0x208, .sliver_reg_ofs = 0xd80, - .phy_id = 0, + .phy_addr = 0, .phy_if = PHY_INTERFACE_MODE_RMII, }, }; diff --git a/board/phytec/pcm051/board.c b/board/phytec/pcm051/board.c index 7e5e07f..1071662 100644 --- a/board/phytec/pcm051/board.c +++ b/board/phytec/pcm051/board.c @@ -176,13 +176,13 @@ static struct cpsw_slave_data cpsw_slaves[] = { { .slave_reg_ofs = 0x208, .sliver_reg_ofs = 0xd80, - .phy_id = 0, + .phy_addr = 0, .phy_if = PHY_INTERFACE_MODE_RGMII, }, { .slave_reg_ofs = 0x308, .sliver_reg_ofs = 0xdc0, - .phy_id = 1, + .phy_addr = 1, .phy_if = PHY_INTERFACE_MODE_RGMII, }, }; diff --git a/board/siemens/dxr2/board.c b/board/siemens/dxr2/board.c index 6c316fa..2172379 100644 --- a/board/siemens/dxr2/board.c +++ b/board/siemens/dxr2/board.c @@ -198,7 +198,7 @@ static struct cpsw_slave_data cpsw_slaves[] = { { .slave_reg_ofs = 0x208, .sliver_reg_ofs = 0xd80, - .phy_id = 0, + .phy_addr = 0, .phy_if = PHY_INTERFACE_MODE_MII, }, }; @@ -232,6 +232,13 @@ int board_eth_init(bd_t *bis) factoryset_setenv(); + /* Reset SMSC LAN9303 switch for default configuration */ + gpio_request(GPIO_LAN9303_NRST, "nRST"); + gpio_direction_output(GPIO_LAN9303_NRST, 0); + /* assert active low reset for 200us */ + udelay(200); + gpio_set_value(GPIO_LAN9303_NRST, 1); + /* Set rgmii mode and enable rmii clock to be sourced from chip */ writel((RMII_MODE_ENABLE | RMII_CHIPCKL_ENABLE), &cdev->miisel); diff --git a/board/siemens/dxr2/mux.c b/board/siemens/dxr2/mux.c index 5c22999..f2314b5 100644 --- a/board/siemens/dxr2/mux.c +++ b/board/siemens/dxr2/mux.c @@ -221,6 +221,8 @@ static struct module_pin_mux gpios_pin_mux[] = { {OFFSET(ain0), MODE(7) | RXACTIVE | PULLUDDIS}, {OFFSET(vrefp), MODE(7) | RXACTIVE | PULLUDDIS}, {OFFSET(vrefn), MODE(7) | RXACTIVE | PULLUDDIS}, + /* nRST for SMSC LAN9303 switch - GPIO2_24 */ + {OFFSET(lcd_pclk), MODE(7) }, /* LAN9303 nRST */ {-1}, }; diff --git a/board/siemens/pxm2/board.c b/board/siemens/pxm2/board.c index ef3d6cc..98083d5 100644 --- a/board/siemens/pxm2/board.c +++ b/board/siemens/pxm2/board.c @@ -181,13 +181,13 @@ static struct cpsw_slave_data cpsw_slaves[] = { { .slave_reg_ofs = 0x208, .sliver_reg_ofs = 0xd80, - .phy_id = 0, + .phy_addr = 0, .phy_if = PHY_INTERFACE_MODE_RMII, }, { .slave_reg_ofs = 0x308, .sliver_reg_ofs = 0xdc0, - .phy_id = 1, + .phy_addr = 1, .phy_if = PHY_INTERFACE_MODE_RMII, }, }; diff --git a/board/siemens/rut/board.c b/board/siemens/rut/board.c index 25ab54d..e0ada3f 100644 --- a/board/siemens/rut/board.c +++ b/board/siemens/rut/board.c @@ -143,13 +143,13 @@ static struct cpsw_slave_data cpsw_slaves[] = { { .slave_reg_ofs = 0x208, .sliver_reg_ofs = 0xd80, - .phy_id = 1, + .phy_addr = 1, .phy_if = PHY_INTERFACE_MODE_RMII, }, { .slave_reg_ofs = 0x308, .sliver_reg_ofs = 0xdc0, - .phy_id = 0, + .phy_addr = 0, .phy_if = PHY_INTERFACE_MODE_RMII, }, }; diff --git a/board/silica/pengwyn/board.c b/board/silica/pengwyn/board.c index a553129..ee88b6f 100644 --- a/board/silica/pengwyn/board.c +++ b/board/silica/pengwyn/board.c @@ -141,13 +141,13 @@ static struct cpsw_slave_data cpsw_slaves[] = { { .slave_reg_ofs = 0x208, .sliver_reg_ofs = 0xd80, - .phy_id = 0, + .phy_addr = 0, .phy_if = PHY_INTERFACE_MODE_MII, }, { .slave_reg_ofs = 0x308, .sliver_reg_ofs = 0xdc0, - .phy_id = 1, + .phy_addr = 1, .phy_if = PHY_INTERFACE_MODE_MII, }, }; diff --git a/board/ti/am335x/board.c b/board/ti/am335x/board.c index 5721768..7609a18 100644 --- a/board/ti/am335x/board.c +++ b/board/ti/am335x/board.c @@ -544,12 +544,12 @@ static struct cpsw_slave_data cpsw_slaves[] = { { .slave_reg_ofs = 0x208, .sliver_reg_ofs = 0xd80, - .phy_id = 0, + .phy_addr = 0, }, { .slave_reg_ofs = 0x308, .sliver_reg_ofs = 0xdc0, - .phy_id = 1, + .phy_addr = 1, }, }; @@ -602,6 +602,21 @@ int board_eth_init(bd_t *bis) } #ifdef CONFIG_DRIVER_TI_CPSW + + mac_lo = readl(&cdev->macid1l); + mac_hi = readl(&cdev->macid1h); + mac_addr[0] = mac_hi & 0xFF; + mac_addr[1] = (mac_hi & 0xFF00) >> 8; + mac_addr[2] = (mac_hi & 0xFF0000) >> 16; + mac_addr[3] = (mac_hi & 0xFF000000) >> 24; + mac_addr[4] = mac_lo & 0xFF; + mac_addr[5] = (mac_lo & 0xFF00) >> 8; + + if (!getenv("eth1addr")) { + if (is_valid_ether_addr(mac_addr)) + eth_setenv_enetaddr("eth1addr", mac_addr); + } + if (read_eeprom(&header) < 0) puts("Could not get board ID.\n"); diff --git a/board/ti/am43xx/board.c b/board/ti/am43xx/board.c index 95fd137..d744977 100644 --- a/board/ti/am43xx/board.c +++ b/board/ti/am43xx/board.c @@ -19,9 +19,13 @@ #include <asm/arch/gpio.h> #include <asm/emif.h> #include "board.h" +#include <miiphy.h> +#include <cpsw.h> DECLARE_GLOBAL_DATA_PTR; +static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE; + /* * Read header information from EEPROM into global structure. */ @@ -200,7 +204,7 @@ const struct emif_regs ddr3_emif_regs_400Mhz = { .read_idle_ctrl = 0x00050000, .zq_config = 0x50074BE4, .temp_alert_config = 0x0, - .emif_ddr_phy_ctlr_1 = 0x0E084008, + .emif_ddr_phy_ctlr_1 = 0x0E004008, .emif_ddr_ext_phy_ctrl_1 = 0x08020080, .emif_ddr_ext_phy_ctrl_2 = 0x00400040, .emif_ddr_ext_phy_ctrl_3 = 0x00400040, @@ -402,3 +406,97 @@ int board_late_init(void) return 0; } #endif + +#ifdef CONFIG_DRIVER_TI_CPSW + +static void cpsw_control(int enabled) +{ + /* Additional controls can be added here */ + return; +} + +static struct cpsw_slave_data cpsw_slaves[] = { + { + .slave_reg_ofs = 0x208, + .sliver_reg_ofs = 0xd80, + .phy_addr = 16, + }, + { + .slave_reg_ofs = 0x308, + .sliver_reg_ofs = 0xdc0, + .phy_addr = 1, + }, +}; + +static struct cpsw_platform_data cpsw_data = { + .mdio_base = CPSW_MDIO_BASE, + .cpsw_base = CPSW_BASE, + .mdio_div = 0xff, + .channels = 8, + .cpdma_reg_ofs = 0x800, + .slaves = 1, + .slave_data = cpsw_slaves, + .ale_reg_ofs = 0xd00, + .ale_entries = 1024, + .host_port_reg_ofs = 0x108, + .hw_stats_reg_ofs = 0x900, + .bd_ram_ofs = 0x2000, + .mac_control = (1 << 5), + .control = cpsw_control, + .host_port_num = 0, + .version = CPSW_CTRL_VERSION_2, +}; + +int board_eth_init(bd_t *bis) +{ + int rv; + uint8_t mac_addr[6]; + uint32_t mac_hi, mac_lo; + + /* try reading mac address from efuse */ + mac_lo = readl(&cdev->macid0l); + mac_hi = readl(&cdev->macid0h); + mac_addr[0] = mac_hi & 0xFF; + mac_addr[1] = (mac_hi & 0xFF00) >> 8; + mac_addr[2] = (mac_hi & 0xFF0000) >> 16; + mac_addr[3] = (mac_hi & 0xFF000000) >> 24; + mac_addr[4] = mac_lo & 0xFF; + mac_addr[5] = (mac_lo & 0xFF00) >> 8; + + if (!getenv("ethaddr")) { + puts("<ethaddr> not set. Validating first E-fuse MAC\n"); + if (is_valid_ether_addr(mac_addr)) + eth_setenv_enetaddr("ethaddr", mac_addr); + } + + mac_lo = readl(&cdev->macid1l); + mac_hi = readl(&cdev->macid1h); + mac_addr[0] = mac_hi & 0xFF; + mac_addr[1] = (mac_hi & 0xFF00) >> 8; + mac_addr[2] = (mac_hi & 0xFF0000) >> 16; + mac_addr[3] = (mac_hi & 0xFF000000) >> 24; + mac_addr[4] = mac_lo & 0xFF; + mac_addr[5] = (mac_lo & 0xFF00) >> 8; + + if (!getenv("eth1addr")) { + if (is_valid_ether_addr(mac_addr)) + eth_setenv_enetaddr("eth1addr", mac_addr); + } + + if (board_is_eposevm()) { + writel(RMII_MODE_ENABLE | RMII_CHIPCKL_ENABLE, &cdev->miisel); + cpsw_slaves[0].phy_if = PHY_INTERFACE_MODE_RMII; + cpsw_slaves[0].phy_addr = 16; + } else { + writel(RGMII_MODE_ENABLE, &cdev->miisel); + cpsw_slaves[0].phy_if = PHY_INTERFACE_MODE_RGMII; + cpsw_slaves[0].phy_addr = 0; + } + + rv = cpsw_register(&cpsw_data); + if (rv < 0) + printf("Error %d registering CPSW switch\n", rv); + + return rv; +} +#endif diff --git a/board/ti/am43xx/mux.c b/board/ti/am43xx/mux.c index c330a81..77c53d2 100644 --- a/board/ti/am43xx/mux.c +++ b/board/ti/am43xx/mux.c @@ -11,6 +11,41 @@ #include <asm/arch/mux.h> #include "board.h" +static struct module_pin_mux rmii1_pin_mux[] = { + {OFFSET(mii1_txen), MODE(1)}, /* RMII1_TXEN */ + {OFFSET(mii1_txd1), MODE(1)}, /* RMII1_TD1 */ + {OFFSET(mii1_txd0), MODE(1)}, /* RMII1_TD0 */ + {OFFSET(mii1_rxd1), MODE(1) | RXACTIVE}, /* RMII1_RD1 */ + {OFFSET(mii1_rxd0), MODE(1) | RXACTIVE}, /* RMII1_RD0 */ + {OFFSET(mii1_rxdv), MODE(1) | RXACTIVE}, /* RMII1_RXDV */ + {OFFSET(mii1_crs), MODE(1) | RXACTIVE}, /* RMII1_CRS_DV */ + {OFFSET(mii1_rxerr), MODE(1) | RXACTIVE}, /* RMII1_RXERR */ + {OFFSET(rmii1_refclk), MODE(0) | RXACTIVE}, /* RMII1_refclk */ + {-1}, +}; + +static struct module_pin_mux rgmii1_pin_mux[] = { + {OFFSET(mii1_txen), MODE(2)}, /* RGMII1_TCTL */ + {OFFSET(mii1_rxdv), MODE(2) | RXACTIVE}, /* RGMII1_RCTL */ + {OFFSET(mii1_txd3), MODE(2)}, /* RGMII1_TD3 */ + {OFFSET(mii1_txd2), MODE(2)}, /* RGMII1_TD2 */ + {OFFSET(mii1_txd1), MODE(2)}, /* RGMII1_TD1 */ + {OFFSET(mii1_txd0), MODE(2)}, /* RGMII1_TD0 */ + {OFFSET(mii1_txclk), MODE(2)}, /* RGMII1_TCLK */ + {OFFSET(mii1_rxclk), MODE(2) | RXACTIVE}, /* RGMII1_RCLK */ + {OFFSET(mii1_rxd3), MODE(2) | RXACTIVE}, /* RGMII1_RD3 */ + {OFFSET(mii1_rxd2), MODE(2) | RXACTIVE}, /* RGMII1_RD2 */ + {OFFSET(mii1_rxd1), MODE(2) | RXACTIVE}, /* RGMII1_RD1 */ + {OFFSET(mii1_rxd0), MODE(2) | RXACTIVE}, /* RGMII1_RD0 */ + {-1}, +}; + +static struct module_pin_mux mdio_pin_mux[] = { + {OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN},/* MDIO_DATA */ + {OFFSET(mdio_clk), MODE(0) | PULLUP_EN}, /* MDIO_CLK */ + {-1}, +}; + static struct module_pin_mux uart0_pin_mux[] = { {OFFSET(uart0_rxd), (MODE(0) | PULLUP_EN | RXACTIVE | SLEWCTRL)}, {OFFSET(uart0_txd), (MODE(0) | PULLUDDIS | PULLUP_EN | SLEWCTRL)}, @@ -57,10 +92,15 @@ void enable_board_pin_mux(void) { configure_module_pin_mux(mmc0_pin_mux); configure_module_pin_mux(i2c0_pin_mux); + configure_module_pin_mux(mdio_pin_mux); - if (board_is_gpevm()) + if (board_is_gpevm()) { configure_module_pin_mux(gpio5_7_pin_mux); - configure_module_pin_mux(qspi_pin_mux); + configure_module_pin_mux(rgmii1_pin_mux); + } else if (board_is_eposevm()) { + configure_module_pin_mux(rmii1_pin_mux); + configure_module_pin_mux(qspi_pin_mux); + } } void enable_i2c0_pin_mux(void) diff --git a/board/ti/dra7xx/evm.c b/board/ti/dra7xx/evm.c index bed8285..c6c4fd1 100644 --- a/board/ti/dra7xx/evm.c +++ b/board/ti/dra7xx/evm.c @@ -149,12 +149,12 @@ static struct cpsw_slave_data cpsw_slaves[] = { { .slave_reg_ofs = 0x208, .sliver_reg_ofs = 0xd80, - .phy_id = 0, + .phy_addr = 2, }, { .slave_reg_ofs = 0x308, .sliver_reg_ofs = 0xdc0, - .phy_id = 1, + .phy_addr = 3, }, }; @@ -216,6 +216,21 @@ int board_eth_init(bd_t *bis) if (is_valid_ether_addr(mac_addr)) eth_setenv_enetaddr("ethaddr", mac_addr); } + + mac_lo = readl((*ctrl)->control_core_mac_id_1_lo); + mac_hi = readl((*ctrl)->control_core_mac_id_1_hi); + mac_addr[0] = (mac_hi & 0xFF0000) >> 16; + mac_addr[1] = (mac_hi & 0xFF00) >> 8; + mac_addr[2] = mac_hi & 0xFF; + mac_addr[3] = (mac_lo & 0xFF0000) >> 16; + mac_addr[4] = (mac_lo & 0xFF00) >> 8; + mac_addr[5] = mac_lo & 0xFF; + + if (!getenv("eth1addr")) { + if (is_valid_ether_addr(mac_addr)) + eth_setenv_enetaddr("eth1addr", mac_addr); + } + ctrl_val = readl((*ctrl)->control_core_control_io1) & (~0x33); ctrl_val |= 0x22; writel(ctrl_val, (*ctrl)->control_core_control_io1); diff --git a/board/ti/ti814x/evm.c b/board/ti/ti814x/evm.c index 140ad71..54b3dfb 100644 --- a/board/ti/ti814x/evm.c +++ b/board/ti/ti814x/evm.c @@ -132,12 +132,12 @@ static struct cpsw_slave_data cpsw_slaves[] = { { .slave_reg_ofs = 0x50, .sliver_reg_ofs = 0x700, - .phy_id = 1, + .phy_addr = 1, }, { .slave_reg_ofs = 0x90, .sliver_reg_ofs = 0x740, - .phy_id = 0, + .phy_addr = 0, }, }; @@ -278,6 +278,8 @@ Active arm armv7 am33xx ti am335x Active arm armv7 am33xx ti am43xx am43xx_evm am43xx_evm:SERIAL1,CONS_INDEX=1 Lokesh Vutla <lokeshvutla@ti.com> Active arm armv7 am33xx ti ti814x ti814x_evm - Matt Porter <matt.porter@linaro.org> Active arm armv7 am33xx ti ti816x ti816x_evm - - +Active arm armv7 at91 atmel sama5d3_xplained sama5d3_xplained_mmc sama5d3_xplained:SAMA5D3,SYS_USE_MMC Bo Shen <voice.shen@atmel.com> +Active arm armv7 at91 atmel sama5d3_xplained sama5d3_xplained_nandflash sama5d3_xplained:SAMA5D3,SYS_USE_NANDFLASH Bo Shen <voice.shen@atmel.com> Active arm armv7 at91 atmel sama5d3xek sama5d3xek_mmc sama5d3xek:SAMA5D3,SYS_USE_MMC Bo Shen <voice.shen@atmel.com> Active arm armv7 at91 atmel sama5d3xek sama5d3xek_nandflash sama5d3xek:SAMA5D3,SYS_USE_NANDFLASH Bo Shen <voice.shen@atmel.com> Active arm armv7 at91 atmel sama5d3xek sama5d3xek_spiflash sama5d3xek:SAMA5D3,SYS_USE_SERIALFLASH Bo Shen <voice.shen@atmel.com> diff --git a/drivers/mtd/nand/atmel_nand.c b/drivers/mtd/nand/atmel_nand.c index 05ddfbb..e1fc48f 100644 --- a/drivers/mtd/nand/atmel_nand.c +++ b/drivers/mtd/nand/atmel_nand.c @@ -31,6 +31,10 @@ #ifdef CONFIG_ATMEL_NAND_HW_PMECC +#ifdef CONFIG_SPL_BUILD +#undef CONFIG_SYS_NAND_ONFI_DETECTION +#endif + struct atmel_nand_host { struct pmecc_regs __iomem *pmecc; struct pmecc_errloc_regs __iomem *pmerrloc; @@ -1169,6 +1173,209 @@ static int at91_nand_ready(struct mtd_info *mtd) } #endif +#ifdef CONFIG_SPL_BUILD +/* The following code is for SPL */ +static nand_info_t mtd; +static struct nand_chip nand_chip; + +static int nand_command(int block, int page, uint32_t offs, u8 cmd) +{ + struct nand_chip *this = mtd.priv; + int page_addr = page + block * CONFIG_SYS_NAND_PAGE_COUNT; + void (*hwctrl)(struct mtd_info *mtd, int cmd, + unsigned int ctrl) = this->cmd_ctrl; + + while (this->dev_ready(&mtd)) + ; + + if (cmd == NAND_CMD_READOOB) { + offs += CONFIG_SYS_NAND_PAGE_SIZE; + cmd = NAND_CMD_READ0; + } + + hwctrl(&mtd, cmd, NAND_CTRL_CLE | NAND_CTRL_CHANGE); + + if (this->options & NAND_BUSWIDTH_16) + offs >>= 1; + + hwctrl(&mtd, offs & 0xff, NAND_CTRL_ALE | NAND_CTRL_CHANGE); + hwctrl(&mtd, (offs >> 8) & 0xff, NAND_CTRL_ALE); + hwctrl(&mtd, (page_addr & 0xff), NAND_CTRL_ALE); + hwctrl(&mtd, ((page_addr >> 8) & 0xff), NAND_CTRL_ALE); +#ifdef CONFIG_SYS_NAND_5_ADDR_CYCLE + hwctrl(&mtd, (page_addr >> 16) & 0x0f, NAND_CTRL_ALE); +#endif + hwctrl(&mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE); + + hwctrl(&mtd, NAND_CMD_READSTART, NAND_CTRL_CLE | NAND_CTRL_CHANGE); + hwctrl(&mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE); + + while (this->dev_ready(&mtd)) + ; + + return 0; +} + +static int nand_is_bad_block(int block) +{ + struct nand_chip *this = mtd.priv; + + nand_command(block, 0, CONFIG_SYS_NAND_BAD_BLOCK_POS, NAND_CMD_READOOB); + + if (this->options & NAND_BUSWIDTH_16) { + if (readw(this->IO_ADDR_R) != 0xffff) + return 1; + } else { + if (readb(this->IO_ADDR_R) != 0xff) + return 1; + } + + return 0; +} + +#ifdef CONFIG_SPL_NAND_ECC +static int nand_ecc_pos[] = CONFIG_SYS_NAND_ECCPOS; +#define ECCSTEPS (CONFIG_SYS_NAND_PAGE_SIZE / \ + CONFIG_SYS_NAND_ECCSIZE) +#define ECCTOTAL (ECCSTEPS * CONFIG_SYS_NAND_ECCBYTES) + +static int nand_read_page(int block, int page, void *dst) +{ + struct nand_chip *this = mtd.priv; + u_char ecc_calc[ECCTOTAL]; + u_char ecc_code[ECCTOTAL]; + u_char oob_data[CONFIG_SYS_NAND_OOBSIZE]; + int eccsize = CONFIG_SYS_NAND_ECCSIZE; + int eccbytes = CONFIG_SYS_NAND_ECCBYTES; + int eccsteps = ECCSTEPS; + int i; + uint8_t *p = dst; + nand_command(block, page, 0, NAND_CMD_READ0); + + for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) { + if (this->ecc.mode != NAND_ECC_SOFT) + this->ecc.hwctl(&mtd, NAND_ECC_READ); + this->read_buf(&mtd, p, eccsize); + this->ecc.calculate(&mtd, p, &ecc_calc[i]); + } + this->read_buf(&mtd, oob_data, CONFIG_SYS_NAND_OOBSIZE); + + for (i = 0; i < ECCTOTAL; i++) + ecc_code[i] = oob_data[nand_ecc_pos[i]]; + + eccsteps = ECCSTEPS; + p = dst; + + for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) + this->ecc.correct(&mtd, p, &ecc_code[i], &ecc_calc[i]); + + return 0; +} +#else +static int nand_read_page(int block, int page, void *dst) +{ + struct nand_chip *this = mtd.priv; + + nand_command(block, page, 0, NAND_CMD_READ0); + atmel_nand_pmecc_read_page(&mtd, this, dst, 0, page); + + return 0; +} +#endif /* CONFIG_SPL_NAND_ECC */ + +int nand_spl_load_image(uint32_t offs, unsigned int size, void *dst) +{ + unsigned int block, lastblock; + unsigned int page; + + block = offs / CONFIG_SYS_NAND_BLOCK_SIZE; + lastblock = (offs + size - 1) / CONFIG_SYS_NAND_BLOCK_SIZE; + page = (offs % CONFIG_SYS_NAND_BLOCK_SIZE) / CONFIG_SYS_NAND_PAGE_SIZE; + + while (block <= lastblock) { + if (!nand_is_bad_block(block)) { + while (page < CONFIG_SYS_NAND_PAGE_COUNT) { + nand_read_page(block, page, dst); + dst += CONFIG_SYS_NAND_PAGE_SIZE; + page++; + } + + page = 0; + } else { + lastblock++; + } + + block++; + } + + return 0; +} + +int at91_nand_wait_ready(struct mtd_info *mtd) +{ + struct nand_chip *this = mtd->priv; + + udelay(this->chip_delay); + + return 0; +} + +int board_nand_init(struct nand_chip *nand) +{ + int ret = 0; + + nand->ecc.mode = NAND_ECC_SOFT; +#ifdef CONFIG_SYS_NAND_DBW_16 + nand->options = NAND_BUSWIDTH_16; + nand->read_buf = nand_read_buf16; +#else + nand->read_buf = nand_read_buf; +#endif + nand->cmd_ctrl = at91_nand_hwcontrol; +#ifdef CONFIG_SYS_NAND_READY_PIN + nand->dev_ready = at91_nand_ready; +#else + nand->dev_ready = at91_nand_wait_ready; +#endif + nand->chip_delay = 20; + +#ifdef CONFIG_ATMEL_NAND_HWECC +#ifdef CONFIG_ATMEL_NAND_HW_PMECC + ret = atmel_pmecc_nand_init_params(nand, &mtd); +#endif +#endif + + return ret; +} + +void nand_init(void) +{ + mtd.writesize = CONFIG_SYS_NAND_PAGE_SIZE; + mtd.oobsize = CONFIG_SYS_NAND_OOBSIZE; + mtd.priv = &nand_chip; + nand_chip.IO_ADDR_R = (void __iomem *)CONFIG_SYS_NAND_BASE; + nand_chip.IO_ADDR_W = (void __iomem *)CONFIG_SYS_NAND_BASE; + board_nand_init(&nand_chip); + +#ifdef CONFIG_SPL_NAND_ECC + if (nand_chip.ecc.mode == NAND_ECC_SOFT) { + nand_chip.ecc.calculate = nand_calculate_ecc; + nand_chip.ecc.correct = nand_correct_data; + } +#endif + + if (nand_chip.select_chip) + nand_chip.select_chip(&mtd, 0); +} + +void nand_deselect(void) +{ + if (nand_chip.select_chip) + nand_chip.select_chip(&mtd, -1); +} + +#else + #ifndef CONFIG_SYS_NAND_BASE_LIST #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } #endif @@ -1227,3 +1434,4 @@ void board_nand_init(void) dev_err(host->dev, "atmel_nand: Fail to initialize #%d chip", i); } +#endif /* CONFIG_SPL_BUILD */ diff --git a/drivers/net/cpsw.c b/drivers/net/cpsw.c index 50167aa..dd6c26a 100644 --- a/drivers/net/cpsw.c +++ b/drivers/net/cpsw.c @@ -656,7 +656,7 @@ static void cpsw_slave_init(struct cpsw_slave *slave, struct cpsw_priv *priv) cpsw_ale_add_mcast(priv, NetBcastAddr, 1 << slave_port); - priv->phy_mask |= 1 << slave->data->phy_id; + priv->phy_mask |= 1 << slave->data->phy_addr; } static struct cpdma_desc *cpdma_desc_alloc(struct cpsw_priv *priv) @@ -948,7 +948,7 @@ static int cpsw_phy_init(struct eth_device *dev, struct cpsw_slave *slave) SUPPORTED_1000baseT_Full); phydev = phy_connect(priv->bus, - CONFIG_PHY_ADDR, + slave->data->phy_addr, dev, slave->data->phy_if); diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h index a5736b7..2020e7f 100644 --- a/include/configs/am335x_evm.h +++ b/include/configs/am335x_evm.h @@ -398,7 +398,6 @@ /* Network. */ #define CONFIG_PHY_GIGE #define CONFIG_PHYLIB -#define CONFIG_PHY_ADDR 0 #define CONFIG_PHY_SMSC /* NAND support */ diff --git a/include/configs/am335x_igep0033.h b/include/configs/am335x_igep0033.h index c00d54f..c17327f 100644 --- a/include/configs/am335x_igep0033.h +++ b/include/configs/am335x_igep0033.h @@ -181,7 +181,6 @@ #define CONFIG_NET_RETRY_COUNT 10 #define CONFIG_NET_MULTI #define CONFIG_PHYLIB -#define CONFIG_PHY_ADDR 0 #define CONFIG_PHY_SMSC /* NAND support */ diff --git a/include/configs/am43xx_evm.h b/include/configs/am43xx_evm.h index c773a18..614857d 100644 --- a/include/configs/am43xx_evm.h +++ b/include/configs/am43xx_evm.h @@ -205,4 +205,30 @@ "run usbboot;" #endif + +/* CPSW Ethernet */ +#define CONFIG_CMD_NET +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_PING +#define CONFIG_CMD_MII +#define CONFIG_DRIVER_TI_CPSW +#define CONFIG_MII +#define CONFIG_BOOTP_DEFAULT +#define CONFIG_BOOTP_DNS +#define CONFIG_BOOTP_DNS2 +#define CONFIG_BOOTP_SEND_HOSTNAME +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_SUBNETMASK +#define CONFIG_NET_RETRY_COUNT 10 +#define CONFIG_NET_MULTI +#define CONFIG_PHY_GIGE +#define CONFIG_PHYLIB + +#define CONFIG_SPL_ENV_SUPPORT +#define CONFIG_SPL_NET_VCI_STRING "AM43xx U-Boot SPL" + +#define CONFIG_SPL_ETH_SUPPORT +#define CONFIG_SPL_NET_SUPPORT +#define CONFIG_SYS_RX_ETH_BUFFER 64 + #endif /* __CONFIG_AM43XX_EVM_H */ diff --git a/include/configs/at91sam9263ek.h b/include/configs/at91sam9263ek.h index b9aa036..48c12ea 100644 --- a/include/configs/at91sam9263ek.h +++ b/include/configs/at91sam9263ek.h @@ -103,6 +103,7 @@ #define CONFIG_CMD_PING 1 #define CONFIG_CMD_DHCP 1 #define CONFIG_CMD_NAND 1 +#define CONFIG_CMD_MMC #define CONFIG_CMD_USB 1 /* SDRAM */ @@ -123,6 +124,18 @@ #define DATAFLASH_TCSS (0x1a << 16) #define DATAFLASH_TCHS (0x1 << 24) +/* MMC */ +#ifdef CONFIG_CMD_MMC +#define CONFIG_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_GENERIC_ATMEL_MCI +#endif + +/* FAT */ +#ifdef CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION +#endif + /* NOR flash, if populated */ #ifdef CONFIG_SYS_USE_NORFLASH #define CONFIG_SYS_FLASH_CFI 1 diff --git a/include/configs/bur_am335x_common.h b/include/configs/bur_am335x_common.h index 1f57bd2..7bbe596 100644 --- a/include/configs/bur_am335x_common.h +++ b/include/configs/bur_am335x_common.h @@ -51,7 +51,6 @@ #define CONFIG_MII /* Required in net/eth.c */ #define CONFIG_SPL_ETH_SUPPORT #define CONFIG_PHYLIB -#define CONFIG_PHY_ADDR 1 #define CONFIG_PHY_NATSEMI #define CONFIG_SPL_NET_SUPPORT #define CONFIG_SPL_ENV_SUPPORT /* used for a fetching MAC-Address */ diff --git a/include/configs/cm_t335.h b/include/configs/cm_t335.h index 56e9a8e..26b615b 100644 --- a/include/configs/cm_t335.h +++ b/include/configs/cm_t335.h @@ -114,7 +114,6 @@ /* Network. */ #define CONFIG_PHY_GIGE #define CONFIG_PHYLIB -#define CONFIG_PHY_ADDR 0 #define CONFIG_PHY_ATHEROS /* NAND support */ diff --git a/include/configs/dra7xx_evm.h b/include/configs/dra7xx_evm.h index c67cf60..291c538 100644 --- a/include/configs/dra7xx_evm.h +++ b/include/configs/dra7xx_evm.h @@ -62,7 +62,6 @@ #define CONFIG_MII /* Required in net/eth.c */ #define CONFIG_PHY_GIGE /* per-board part of CPSW */ #define CONFIG_PHYLIB -#define CONFIG_PHY_ADDR 2 /* SPI */ #undef CONFIG_OMAP3_SPI diff --git a/include/configs/dxr2.h b/include/configs/dxr2.h index 1e42f5c..75f7812 100644 --- a/include/configs/dxr2.h +++ b/include/configs/dxr2.h @@ -26,6 +26,7 @@ #define BOARD_DFU_BUTTON_GPIO 27 #define BOARD_DFU_BUTTON_LED 64 +#define GPIO_LAN9303_NRST 88 /* GPIO2_24 = gpio88 */ #undef CONFIG_DOS_PARTITION #undef CONFIG_CMD_FAT @@ -49,7 +50,6 @@ #undef CONFIG_MII #undef CONFIG_PHY_GIGE -#define CONFIG_PHY_ADDR 0 #define CONFIG_PHY_SMSC #define CONFIG_FACTORYSET diff --git a/include/configs/omap3_igep00x0.h b/include/configs/omap3_igep00x0.h index 12d8141..d56d5b0 100644 --- a/include/configs/omap3_igep00x0.h +++ b/include/configs/omap3_igep00x0.h @@ -37,6 +37,11 @@ #define CONFIG_SHOW_BOOT_PROGRESS #endif +/* GPIO banks */ +#define CONFIG_OMAP3_GPIO_3 /* GPIO64 .. 95 is in GPIO bank 3 */ +#define CONFIG_OMAP3_GPIO_5 /* GPIO128..159 is in GPIO bank 5 */ +#define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO bank 6 */ + /* USB */ #define CONFIG_MUSB_UDC 1 #define CONFIG_USB_OMAP3 1 diff --git a/include/configs/pcm051.h b/include/configs/pcm051.h index 6f41ee7..9af3efd 100644 --- a/include/configs/pcm051.h +++ b/include/configs/pcm051.h @@ -297,7 +297,6 @@ #define CONFIG_NET_MULTI #define CONFIG_PHY_GIGE #define CONFIG_PHYLIB -#define CONFIG_PHY_ADDR 0 #define CONFIG_PHY_SMSC #endif /* ! __CONFIG_PCM051_H */ diff --git a/include/configs/pengwyn.h b/include/configs/pengwyn.h index 5a55556..fc25966 100644 --- a/include/configs/pengwyn.h +++ b/include/configs/pengwyn.h @@ -196,7 +196,6 @@ /* Network */ #define CONFIG_CMD_MII #define CONFIG_PHYLIB -#define CONFIG_PHY_ADDR 1 #define CONFIG_PHY_RESET 1 #define CONFIG_PHY_NATSEMI diff --git a/include/configs/pxm2.h b/include/configs/pxm2.h index 7722f7b..6276d43 100644 --- a/include/configs/pxm2.h +++ b/include/configs/pxm2.h @@ -44,7 +44,6 @@ #undef CONFIG_SPL_NET_VCI_STRING #undef CONFIG_SPL_ETH_SUPPORT -#define CONFIG_PHY_ADDR 0 #define CONFIG_PHY_ATHEROS #define CONFIG_FACTORYSET diff --git a/include/configs/rut.h b/include/configs/rut.h index d4519f9..6bddede 100644 --- a/include/configs/rut.h +++ b/include/configs/rut.h @@ -41,7 +41,6 @@ #undef CONFIG_SPL_NET_VCI_STRING #undef CONFIG_SPL_ETH_SUPPORT -#define CONFIG_PHY_ADDR 1 #define CONFIG_PHY_NATSEMI #define CONFIG_FACTORYSET diff --git a/include/configs/sama5d3_xplained.h b/include/configs/sama5d3_xplained.h new file mode 100644 index 0000000..91cc7d8 --- /dev/null +++ b/include/configs/sama5d3_xplained.h @@ -0,0 +1,203 @@ +/* + * Configuration settings for the SAMA5D3 Xplained board. + * + * Copyright (C) 2014 Atmel Corporation + * Bo Shen <voice.shen@atmel.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#include <asm/hardware.h> + +#define CONFIG_SYS_TEXT_BASE 0x26f00000 + +/* ARM asynchronous clock */ +#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 +#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */ +#define CONFIG_SYS_HZ 1000 + +#define CONFIG_AT91FAMILY +#define CONFIG_ARCH_CPU_INIT +#define CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_DISPLAY_CPUINFO + +#define CONFIG_CMD_BOOTZ +#define CONFIG_OF_LIBFDT /* Device Tree support */ + +/* general purpose I/O */ +#define CONFIG_AT91_GPIO + +/* serial console */ +#define CONFIG_ATMEL_USART +#define CONFIG_USART_BASE ATMEL_BASE_DBGU +#define CONFIG_USART_ID ATMEL_ID_DBGU + +/* + * This needs to be defined for the OHCI code to work but it is defined as + * ATMEL_ID_UHPHS in the CPU specific header files. + */ +#define ATMEL_ID_UHP ATMEL_ID_UHPHS + +/* + * Specify the clock enable bit in the PMC_SCER register. + */ +#define ATMEL_PMC_UHP AT91SAM926x_PMC_UHP + +#define CONFIG_BOOTDELAY 3 + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + +/* No NOR flash */ +#define CONFIG_SYS_NO_FLASH + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_IMI +#undef CONFIG_CMD_LOADS +#define CONFIG_CMD_PING +#define CONFIG_CMD_DHCP + +/* SDRAM */ +#define CONFIG_NR_DRAM_BANKS 1 +#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_DDRCS +#define CONFIG_SYS_SDRAM_SIZE 0x10000000 + +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE) + +/* NAND flash */ +#define CONFIG_CMD_NAND + +#ifdef CONFIG_CMD_NAND +#define CONFIG_NAND_ATMEL +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 +/* our ALE is AD21 */ +#define CONFIG_SYS_NAND_MASK_ALE (1 << 21) +/* our CLE is AD22 */ +#define CONFIG_SYS_NAND_MASK_CLE (1 << 22) +#define CONFIG_SYS_NAND_ONFI_DETECTION +/* PMECC & PMERRLOC */ +#define CONFIG_ATMEL_NAND_HWECC +#define CONFIG_ATMEL_NAND_HW_PMECC +#define CONFIG_PMECC_CAP 4 +#define CONFIG_PMECC_SECTOR_SIZE 512 +#define CONFIG_CMD_NAND_TRIMFFS +#define CONFIG_CMD_MTDPARTS + +#define CONFIG_MTD_DEVICE +#define CONFIG_MTD_PARTITIONS +#define CONFIG_RBTREE +#define CONFIG_LZO +#define CONFIG_CMD_UBI +#define CONFIG_CMD_UBIFS +#endif + +/* Ethernet Hardware */ +#define CONFIG_MACB +#define CONFIG_RMII +#define CONFIG_NET_MULTI +#define CONFIG_NET_RETRY_COUNT 20 +#define CONFIG_MACB_SEARCH_PHY +#define CONFIG_RGMII +#define CONFIG_CMD_MII +#define CONFIG_PHYLIB + +/* MMC */ +#define CONFIG_CMD_MMC + +#ifdef CONFIG_CMD_MMC +#define CONFIG_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_GENERIC_ATMEL_MCI +#define CONFIG_ATMEL_MCI_8BIT +#endif + +/* USB */ +#define CONFIG_CMD_USB + +#ifdef CONFIG_CMD_USB +#define CONFIG_USB_ATMEL +#define CONFIG_USB_ATMEL_CLK_SEL_UPLL +#define CONFIG_USB_OHCI_NEW +#define CONFIG_SYS_USB_OHCI_CPU_INIT +#define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_BASE_OHCI +#define CONFIG_SYS_USB_OHCI_SLOT_NAME "SAMA5D3 Xplained" +#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 +#define CONFIG_DOS_PARTITION +#define CONFIG_USB_STORAGE +#endif + +#if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC) +#define CONFIG_CMD_FAT +#define CONFIG_FAT_WRITE +#define CONFIG_CMD_EXT4 +#define CONFIG_CMD_EXT4_WRITE +#endif + +#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */ + +#if CONFIG_SYS_USE_NANDFLASH +/* bootstrap + u-boot + env in nandflash */ +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_OFFSET 0xc0000 +#define CONFIG_ENV_OFFSET_REDUND 0x100000 +#define CONFIG_ENV_SIZE 0x20000 +#define CONFIG_BOOTCOMMAND "nand read 0x21000000 0x180000 0x80000;" \ + "nand read 0x22000000 0x200000 0x600000;" \ + "bootz 0x22000000 - 0x21000000" +#elif CONFIG_SYS_USE_MMC +/* bootstrap + u-boot + env in sd card */ +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_ENV_OFFSET 0x2000 +#define CONFIG_ENV_SIZE 0x1000 +#define CONFIG_BOOTCOMMAND "fatload mmc 0:1 0x21000000 at91-sama5d3_xplained.dtb; " \ + "fatload mmc 0:1 0x22000000 zImage; " \ + "bootz 0x22000000 - 0x21000000" +#define CONFIG_SYS_MMC_ENV_DEV 0 +#else +#define CONFIG_ENV_IS_NOWHERE +#endif + +#ifdef CONFIG_SYS_USE_MMC +#define CONFIG_BOOTARGS \ + "console=ttyS0,115200 earlyprintk " \ + "root=/dev/mmcblk0p2 rw rootwait" +#else +#define CONFIG_BOOTARGS \ + "console=ttyS0,115200 earlyprintk " \ + "mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro," \ + "256K(env),256k(evn_redundent),256k(spare)," \ + "512k(dtb),6M(kernel)ro,-(rootfs) " \ + "rootfstype=ubifs ubi.mtd=7 root=ubi0:rootfs" +#endif + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_SYS_PROMPT "U-Boot> " +#define CONFIG_SYS_CBSIZE 256 +#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_LONGHELP +#define CONFIG_CMDLINE_EDITING +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_HUSH_PARSER + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) + +#endif diff --git a/include/configs/sama5d3xek.h b/include/configs/sama5d3xek.h index c34feb5..516be85 100644 --- a/include/configs/sama5d3xek.h +++ b/include/configs/sama5d3xek.h @@ -258,6 +258,8 @@ #define CONFIG_SPL_SERIAL_SUPPORT #define CONFIG_SPL_BOARD_INIT +#define CONFIG_SYS_MONITOR_LEN (512 << 10) + #ifdef CONFIG_SYS_USE_MMC #define CONFIG_SPL_LDSCRIPT arch/arm/cpu/at91-common/u-boot-spl.lds #define CONFIG_SPL_MMC_SUPPORT @@ -267,6 +269,27 @@ #define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img" #define CONFIG_SPL_FAT_SUPPORT #define CONFIG_SPL_LIBDISK_SUPPORT + +#elif CONFIG_SYS_USE_NANDFLASH +#define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_DRIVERS +#define CONFIG_SPL_NAND_BASE +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000 +#define CONFIG_SYS_NAND_5_ADDR_CYCLE +#define CONFIG_SYS_NAND_PAGE_SIZE 0x800 +#define CONFIG_SYS_NAND_PAGE_COUNT 64 +#define CONFIG_SYS_NAND_OOBSIZE 64 +#define CONFIG_SYS_NAND_BLOCK_SIZE 0x20000 +#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0x0 + +#elif CONFIG_SYS_USE_SERIALFLASH +#define CONFIG_SPL_SPI_SUPPORT +#define CONFIG_SPL_SPI_FLASH_SUPPORT +#define CONFIG_SPL_SPI_LOAD +#define CONFIG_SPL_SPI_BUS 0 +#define CONFIG_SPL_SPI_CS 0 +#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x8400 + #endif #endif diff --git a/include/configs/tegra-common-post.h b/include/configs/tegra-common-post.h index e1a3bbc..76dad4e 100644 --- a/include/configs/tegra-common-post.h +++ b/include/configs/tegra-common-post.h @@ -66,27 +66,63 @@ #define BOOT_TARGETS_DHCP "" #endif +#if defined(CONFIG_CMD_DHCP) && defined(CONFIG_CMD_PXE) +#define BOOTCMDS_PXE \ + "bootcmd_pxe=" \ + BOOTCMD_INIT_USB \ + "dhcp; " \ + "if pxe get; then " \ + "pxe boot; " \ + "fi\0" +#define BOOT_TARGETS_PXE "pxe" +#else +#define BOOTCMDS_PXE "" +#define BOOT_TARGETS_PXE "" +#endif + #define BOOTCMDS_COMMON \ "rootpart=1\0" \ \ + "do_script_boot=" \ + "load ${devtype} ${devnum}:${rootpart} " \ + "${scriptaddr} ${prefix}${script}; " \ + "source ${scriptaddr}\0" \ + \ "script_boot=" \ - "if load ${devtype} ${devnum}:${rootpart} " \ - "${scriptaddr} ${prefix}${script}; then " \ - "echo ${script} found! Executing ...;" \ - "source ${scriptaddr};" \ - "fi;\0" \ + "for script in ${boot_scripts}; do " \ + "if test -e ${devtype} ${devnum}:${rootpart} " \ + "${prefix}${script}; then " \ + "echo Found U-Boot script " \ + "${prefix}${script}; " \ + "run do_script_boot; " \ + "echo SCRIPT FAILED: continuing...; " \ + "fi; " \ + "done\0" \ + \ + "do_sysboot_boot=" \ + "sysboot ${devtype} ${devnum}:${rootpart} any " \ + "${scriptaddr} ${prefix}extlinux.conf\0" \ + \ + "sysboot_boot=" \ + "if test -e ${devtype} ${devnum}:${rootpart} " \ + "${prefix}extlinux.conf; then " \ + "echo Found extlinux config " \ + "${prefix}extlinux.conf; " \ + "run do_sysboot_boot; " \ + "echo SCRIPT FAILED: continuing...; " \ + "fi\0" \ \ "scan_boot=" \ "echo Scanning ${devtype} ${devnum}...; " \ "for prefix in ${boot_prefixes}; do " \ - "for script in ${boot_scripts}; do " \ - "run script_boot; " \ - "done; " \ - "done;\0" \ + "run sysboot_boot; " \ + "run script_boot; " \ + "done\0" \ \ "boot_targets=" \ BOOT_TARGETS_MMC " " \ BOOT_TARGETS_USB " " \ + BOOT_TARGETS_PXE " " \ BOOT_TARGETS_DHCP " " \ "\0" \ \ @@ -96,7 +132,8 @@ \ BOOTCMDS_MMC \ BOOTCMDS_USB \ - BOOTCMDS_DHCP + BOOTCMDS_DHCP \ + BOOTCMDS_PXE #define CONFIG_BOOTCOMMAND \ "set usb_need_init; " \ diff --git a/include/configs/tegra-common.h b/include/configs/tegra-common.h index 9247aefdb..ae786cf 100644 --- a/include/configs/tegra-common.h +++ b/include/configs/tegra-common.h @@ -29,7 +29,6 @@ #define CONFIG_DISPLAY_BOARDINFO #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ -#define CONFIG_OF_LIBFDT /* enable passing of devicetree */ /* Environment */ #define CONFIG_ENV_VARS_UBOOT_CONFIG @@ -69,33 +68,20 @@ #undef CONFIG_CMD_NET /* network support */ /* turn on command-line edit/hist/auto */ -#define CONFIG_CMDLINE_EDITING #define CONFIG_COMMAND_HISTORY -#define CONFIG_AUTO_COMPLETE /* turn on commonly used storage-related commands */ - -#define CONFIG_DOS_PARTITION -#define CONFIG_EFI_PARTITION #define CONFIG_PARTITION_UUIDS -#define CONFIG_FS_EXT4 -#define CONFIG_FS_FAT -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_FAT -#define CONFIG_CMD_FS_GENERIC #define CONFIG_CMD_PART #define CONFIG_SYS_NO_FLASH #define CONFIG_CONSOLE_MUX #define CONFIG_SYS_CONSOLE_IS_IN_ENV -#define CONFIG_BOOTDELAY 2 /* -1 to disable auto boot */ /* * Miscellaneous configurable options */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ #define CONFIG_SYS_PROMPT V_PROMPT /* * Increasing the size of the IO buffer as default nfsargs size is more @@ -133,8 +119,6 @@ #define CONFIG_TEGRA_GPIO #define CONFIG_CMD_GPIO #define CONFIG_CMD_ENTERRCM -#define CONFIG_CMD_BOOTZ -#define CONFIG_SUPPORT_RAW_INITRD /* Defines for SPL */ #define CONFIG_SPL @@ -161,4 +145,8 @@ #define CONFIG_BOUNCE_BUFFER #define CONFIG_CRC32_VERIFY +#ifndef CONFIG_SPL_BUILD +#include <config_distro_defaults.h> +#endif + #endif /* _TEGRA_COMMON_H_ */ diff --git a/include/configs/tegra114-common.h b/include/configs/tegra114-common.h index a4e8a5f..555c237 100644 --- a/include/configs/tegra114-common.h +++ b/include/configs/tegra114-common.h @@ -26,11 +26,6 @@ */ #define V_NS16550_CLK 408000000 /* 408MHz (pllp_out0) */ -/* - * High Level Configuration Options - */ -#define CONFIG_TEGRA114 /* in a NVidia Tegra114 core */ - /* Environment information, boards can override if required */ #define CONFIG_LOADADDR 0x80408000 /* def. location for kernel */ @@ -51,6 +46,9 @@ * scriptaddr can be pretty much anywhere that doesn't conflict with something * else. Put it above BOOTMAPSZ to eliminate conflicts. * + * pxefile_addr_r can be pretty much anywhere that doesn't conflict with + * something else. Put it above BOOTMAPSZ to eliminate conflicts. + * * kernel_addr_r must be within the first 128M of RAM in order for the * kernel's CONFIG_AUTO_ZRELADDR option to work. Since the kernel will * decompress itself to 0x8000 after the start of RAM, kernel_addr_r @@ -68,6 +66,7 @@ */ #define MEM_LAYOUT_ENV_SETTINGS \ "scriptaddr=0x90000000\0" \ + "pxefile_addr_r=0x90100000\0" \ "kernel_addr_r=0x81000000\0" \ "fdt_addr_r=0x82000000\0" \ "ramdisk_addr_r=0x82100000\0" @@ -83,5 +82,6 @@ /* For USB EHCI controller */ #define CONFIG_EHCI_IS_TDI #define CONFIG_USB_EHCI_TXFIFO_THRESH 0x10 +#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 1 #endif /* _TEGRA114_COMMON_H_ */ diff --git a/include/configs/tegra124-common.h b/include/configs/tegra124-common.h index 0a4541b..61e5026 100644 --- a/include/configs/tegra124-common.h +++ b/include/configs/tegra124-common.h @@ -18,11 +18,6 @@ */ #define V_NS16550_CLK 408000000 /* 408MHz (pllp_out0) */ -/* - * High Level Configuration Options - */ -#define CONFIG_TEGRA124 /* is an NVIDIA Tegra124 core */ - /* Environment information, boards can override if required */ #define CONFIG_LOADADDR 0x80408000 /* def. location for kernel */ @@ -79,5 +74,6 @@ /* For USB EHCI controller */ #define CONFIG_EHCI_IS_TDI #define CONFIG_USB_EHCI_TXFIFO_THRESH 0x10 +#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 1 #endif /* _TEGRA124_COMMON_H_ */ diff --git a/include/configs/tegra20-common.h b/include/configs/tegra20-common.h index b009a31..21bf977 100644 --- a/include/configs/tegra20-common.h +++ b/include/configs/tegra20-common.h @@ -24,11 +24,6 @@ */ #define V_NS16550_CLK 216000000 /* 216MHz (pllp_out0) */ -/* - * High Level Configuration Options - */ -#define CONFIG_TEGRA20 /* in a NVidia Tegra20 core */ - /* Environment information, boards can override if required */ #define CONFIG_LOADADDR 0x00408000 /* def. location for kernel */ @@ -49,6 +44,9 @@ * scriptaddr can be pretty much anywhere that doesn't conflict with something * else. Put it above BOOTMAPSZ to eliminate conflicts. * + * pxefile_addr_r can be pretty much anywhere that doesn't conflict with + * something else. Put it above BOOTMAPSZ to eliminate conflicts. + * * kernel_addr_r must be within the first 128M of RAM in order for the * kernel's CONFIG_AUTO_ZRELADDR option to work. Since the kernel will * decompress itself to 0x8000 after the start of RAM, kernel_addr_r @@ -66,6 +64,7 @@ */ #define MEM_LAYOUT_ENV_SETTINGS \ "scriptaddr=0x10000000\0" \ + "pxefile_addr_r=0x10100000\0" \ "kernel_addr_r=0x01000000\0" \ "fdt_addr_r=0x02000000\0" \ "ramdisk_addr_r=0x02100000\0" @@ -96,6 +95,7 @@ */ #define CONFIG_USB_EHCI_TXFIFO_THRESH 10 #define CONFIG_EHCI_IS_TDI +#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 1 /* Total I2C ports on Tegra20 */ #define TEGRA_I2C_NUM_CONTROLLERS 4 diff --git a/include/configs/tegra30-common.h b/include/configs/tegra30-common.h index b5550d7..443c842 100644 --- a/include/configs/tegra30-common.h +++ b/include/configs/tegra30-common.h @@ -23,11 +23,6 @@ */ #define V_NS16550_CLK 408000000 /* 408MHz (pllp_out0) */ -/* - * High Level Configuration Options - */ -#define CONFIG_TEGRA30 /* in a NVidia Tegra30 core */ - /* Environment information, boards can override if required */ #define CONFIG_LOADADDR 0x80408000 /* def. location for kernel */ @@ -48,6 +43,9 @@ * scriptaddr can be pretty much anywhere that doesn't conflict with something * else. Put it above BOOTMAPSZ to eliminate conflicts. * + * pxefile_addr_r can be pretty much anywhere that doesn't conflict with + * something else. Put it above BOOTMAPSZ to eliminate conflicts. + * * kernel_addr_r must be within the first 128M of RAM in order for the * kernel's CONFIG_AUTO_ZRELADDR option to work. Since the kernel will * decompress itself to 0x8000 after the start of RAM, kernel_addr_r @@ -65,6 +63,7 @@ */ #define MEM_LAYOUT_ENV_SETTINGS \ "scriptaddr=0x90000000\0" \ + "pxefile_addr_r=0x90100000\0" \ "kernel_addr_r=0x81000000\0" \ "fdt_addr_r=0x82000000\0" \ "ramdisk_addr_r=0x82100000\0" @@ -80,5 +79,6 @@ /* For USB EHCI controller */ #define CONFIG_EHCI_IS_TDI #define CONFIG_USB_EHCI_TXFIFO_THRESH 0x10 +#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 1 #endif /* _TEGRA30_COMMON_H_ */ diff --git a/include/configs/ti814x_evm.h b/include/configs/ti814x_evm.h index ba16b1c..b51400c 100644 --- a/include/configs/ti814x_evm.h +++ b/include/configs/ti814x_evm.h @@ -233,7 +233,6 @@ #define CONFIG_NET_MULTI #define CONFIG_PHY_GIGE #define CONFIG_PHYLIB -#define CONFIG_PHY_ADDR 1 #define CONFIG_PHY_ET1011C #define CONFIG_PHY_ET1011C_TX_CLK_FIX diff --git a/include/configs/ti_am335x_common.h b/include/configs/ti_am335x_common.h index 7e9ca01..50c3203 100644 --- a/include/configs/ti_am335x_common.h +++ b/include/configs/ti_am335x_common.h @@ -30,6 +30,7 @@ /* Network defines. */ #define CONFIG_CMD_NET /* 'bootp' and 'tftp' */ #define CONFIG_CMD_DHCP +#define CONFIG_CMD_MII #define CONFIG_BOOTP_DNS /* Configurable parts of CMD_DHCP */ #define CONFIG_BOOTP_DNS2 #define CONFIG_BOOTP_SEND_HOSTNAME diff --git a/include/cpsw.h b/include/cpsw.h index 743cb96..a73843d 100644 --- a/include/cpsw.h +++ b/include/cpsw.h @@ -19,7 +19,7 @@ struct cpsw_slave_data { u32 slave_reg_ofs; u32 sliver_reg_ofs; - int phy_id; + int phy_addr; int phy_if; }; diff --git a/include/nand.h b/include/nand.h index 84116f4..fc735d1 100644 --- a/include/nand.h +++ b/include/nand.h @@ -21,10 +21,16 @@ * at the same time, so do it here. When all drivers are * converted, this will go away. */ +#ifdef CONFIG_SPL_BUILD +#if defined(CONFIG_NAND_FSL_ELBC) || defined(CONFIG_NAND_FSL_IFC) +#define CONFIG_SYS_NAND_SELF_INIT +#endif +#else #if defined(CONFIG_NAND_FSL_ELBC) || defined(CONFIG_NAND_ATMEL)\ || defined(CONFIG_NAND_FSL_IFC) #define CONFIG_SYS_NAND_SELF_INIT #endif +#endif extern void nand_init(void); |