diff options
101 files changed, 4084 insertions, 432 deletions
@@ -944,8 +944,9 @@ INPUTS-$(CONFIG_SPL_FRAMEWORK) += u-boot.img endif endif INPUTS-$(CONFIG_TPL) += tpl/u-boot-tpl.bin -INPUTS-$(CONFIG_OF_SEPARATE) += u-boot.dtb -INPUTS-$(CONFIG_BINMAN_STANDALONE_FDT) += u-boot.dtb + +# Allow omitting the .dtb output if it is not normally used +INPUTS-$(CONFIG_OF_SEPARATE) += $(if $(CONFIG_OF_OMIT_DTB),dts/dt.dtb,u-boot.dtb) ifeq ($(CONFIG_SPL_FRAMEWORK),y) INPUTS-$(CONFIG_OF_SEPARATE) += u-boot-dtb.img endif @@ -1054,6 +1055,10 @@ quiet_cmd_cfgcheck = CFGCHK $2 cmd_cfgcheck = $(srctree)/scripts/check-config.sh $2 \ $(srctree)/scripts/config_whitelist.txt $(srctree) +quiet_cmd_ofcheck = OFCHK $2 +cmd_ofcheck = $(srctree)/scripts/check-of.sh $2 \ + $(srctree)/scripts/of_allowlist.txt + # Concat the value of all the CONFIGs (result is 'y' or 'yy', etc. ) got = $(foreach cfg,$(1),$($(cfg))) @@ -1128,6 +1133,9 @@ endif @# know about unless they are in Kconfig. All the existing CONFIG @# options are whitelisted, so new ones should not be added. $(call cmd,cfgcheck,u-boot.cfg) + @# Check that this build does not override OF_HAS_PRIOR_STAGE by + @# disabling OF_BOARD. + $(call cmd,ofcheck,$(KCONFIG_CONFIG)) PHONY += dtbs dtbs: dts/dt.dtb @@ -1181,7 +1189,7 @@ u-boot.bin: u-boot-fit-dtb.bin FORCE u-boot-dtb.bin: u-boot-nodtb.bin dts/dt.dtb FORCE $(call if_changed,cat) -else ifeq ($(CONFIG_OF_SEPARATE),y) +else ifeq ($(CONFIG_OF_SEPARATE).$(CONFIG_OF_OMIT_DTB),y.) u-boot-dtb.bin: u-boot-nodtb.bin dts/dt.dtb FORCE $(call if_changed,cat) @@ -1415,7 +1423,7 @@ u-boot-lzma.img: u-boot.bin.lzma FORCE u-boot-dtb.img u-boot.img u-boot.kwb u-boot.pbl u-boot-ivt.img: \ $(if $(CONFIG_SPL_LOAD_FIT),u-boot-nodtb.bin \ - $(if $(CONFIG_OF_SEPARATE)$(CONFIG_OF_EMBED)$(CONFIG_SANDBOX)$(CONFIG_BINMAN_STANDALONE_FDT),dts/dt.dtb) \ + $(if $(CONFIG_OF_SEPARATE)$(CONFIG_OF_EMBED)$(CONFIG_SANDBOX),dts/dt.dtb) \ ,$(UBOOT_BIN)) FORCE $(call if_changed,mkimage) $(BOARD_SIZE_CHECK) @@ -646,35 +646,6 @@ The following options need to be configured: which adds regex support to some commands, as for example "env grep" and "setexpr". -- Device tree: - CONFIG_OF_CONTROL - If this variable is defined, U-Boot will use a device tree - to configure its devices, instead of relying on statically - compiled #defines in the board file. This option is - experimental and only available on a few boards. The device - tree is available in the global data as gd->fdt_blob. - - U-Boot needs to get its device tree from somewhere. This can - be done using one of the three options below: - - CONFIG_OF_SEPARATE - If this variable is defined, U-Boot will build a device tree - binary. It will be called u-boot.dtb. Architecture-specific - code will locate it at run-time. Generally this works by: - - cat u-boot.bin u-boot.dtb >image.bin - - and in fact, U-Boot does this for you, creating a file called - u-boot-dtb.bin which is useful in the common case. You can - still use the individual files if you need something more - exotic. - - CONFIG_OF_BOARD - If this variable is defined, U-Boot will use the device tree - provided by the board at runtime instead of embedding one with - the image. Only boards defining board_fdt_blob_setup() support - this option (see include/fdtdec.h file). - - Watchdog: CONFIG_WATCHDOG If this variable is defined, it enables watchdog diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index eed27af..85c964b 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -635,6 +635,7 @@ config ARCH_BCMSTB select GPIO_EXTRA_HEADER select OF_CONTROL imply CMD_DM + imply OF_HAS_PRIOR_STAGE help This enables support for Broadcom ARM-based set-top box chipsets, including the 7445 family of chips. @@ -707,12 +708,12 @@ config ARCH_HIGHBANK select DM select DM_SERIAL select OF_CONTROL - select OF_BOARD select CLK select CLK_CCF select AHCI select DM_ETH select PHYS_64BIT + imply OF_HAS_PRIOR_STAGE config ARCH_INTEGRATOR bool "ARM Ltd. Integrator family" @@ -935,13 +936,13 @@ config ARCH_APPLE select IOMMU select LINUX_KERNEL_IMAGE_HEADER select OF_CONTROL - select OF_BOARD select PINCTRL select POSITION_INDEPENDENT select USB imply CMD_DM imply CMD_GPT imply DISTRO_DEFAULTS + imply OF_HAS_PRIOR_STAGE config ARCH_OWL bool "Actions Semi OWL SoCs" @@ -966,6 +967,7 @@ config ARCH_QEMU imply DM_RNG imply DM_RTC imply RTC_PL031 + imply OF_HAS_PRIOR_STAGE config ARCH_RMOBILE bool "Renesas ARM SoCs" @@ -1243,7 +1245,6 @@ config TARGET_VEXPRESS64_JUNO select PL01X_SERIAL select DM select OF_CONTROL - select OF_BOARD select CLK select DM_SERIAL select ARM_PSCI_FW @@ -1251,6 +1252,7 @@ config TARGET_VEXPRESS64_JUNO select DM_ETH select BLK select USB + imply OF_HAS_PRIOR_STAGE config TARGET_TOTAL_COMPUTE bool "Support Total Compute Platform" @@ -1907,6 +1909,7 @@ config ARCH_OCTEONTX select OF_LIVE select BOARD_LATE_INIT select SYS_CACHE_SHIFT_7 + imply OF_HAS_PRIOR_STAGE config ARCH_OCTEONTX2 bool "Support OcteonTX2 SoCs" @@ -1918,6 +1921,7 @@ config ARCH_OCTEONTX2 select OF_LIVE select BOARD_LATE_INIT select SYS_CACHE_SHIFT_7 + imply OF_HAS_PRIOR_STAGE config TARGET_THUNDERX_88XX bool "Support ThunderX 88xx" @@ -1954,6 +1958,8 @@ config TARGET_XENGUEST_ARM64 select LINUX_KERNEL_IMAGE_HEADER select XEN_SERIAL select SSCANF + imply OF_HAS_PRIOR_STAGE + endchoice config SUPPORT_PASSING_ATAGS diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 7f622fe..453e2fd 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -360,7 +360,8 @@ dtb-$(CONFIG_ARCH_ZYNQMP) += \ dtb-$(CONFIG_ARCH_VERSAL) += \ versal-mini.dtb \ versal-mini-emmc0.dtb \ - versal-mini-emmc1.dtb + versal-mini-emmc1.dtb \ + xilinx-versal-virt.dtb dtb-$(CONFIG_ARCH_ZYNQMP_R5) += \ zynqmp-r5.dtb dtb-$(CONFIG_AM33XX) += \ @@ -870,6 +871,8 @@ dtb-$(CONFIG_MX7) += imx7d-sdb.dtb \ dtb-$(CONFIG_ARCH_MX7ULP) += imx7ulp-com.dtb \ imx7ulp-evk.dtb +dtb-$(CONFIG_ARCH_HIGHBANK) += highbank.dtb + dtb-$(CONFIG_ARCH_IMX8) += \ fsl-imx8qm-apalis.dtb \ fsl-imx8qm-mek.dtb \ @@ -1077,7 +1080,8 @@ dtb-$(CONFIG_ARCH_BCM283X) += \ bcm2837-rpi-3-a-plus.dtb \ bcm2837-rpi-3-b.dtb \ bcm2837-rpi-3-b-plus.dtb \ - bcm2837-rpi-cm3-io3.dtb + bcm2837-rpi-cm3-io3.dtb \ + bcm2711-rpi-4-b.dtb dtb-$(CONFIG_ARCH_BCM63158) += \ bcm963158.dtb @@ -1090,6 +1094,8 @@ dtb-$(CONFIG_ARCH_BCM6858) += \ dtb-$(CONFIG_TARGET_BCMNS3) += ns3-board.dtb +dtb-$(CONFIG_ARCH_BCMSTB) += bcm7xxx.dtb + dtb-$(CONFIG_ASPEED_AST2500) += ast2500-evb.dtb dtb-$(CONFIG_ASPEED_AST2600) += ast2600-evb.dtb @@ -1139,6 +1145,11 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \ mt8516-pumpkin.dtb \ mt8518-ap1-emmc.dtb +dtb-$(CONFIG_XEN) += xenguest-arm64.dtb + +dtb-$(CONFIG_ARCH_OCTEONTX) += octeontx.dtb +dtb-$(CONFIG_ARCH_OCTEONTX2) += octeontx.dtb + dtb-$(CONFIG_TARGET_GE_BX50V3) += \ imx6q-bx50v3.dtb \ imx6q-b850v3.dtb \ @@ -1148,7 +1159,10 @@ dtb-$(CONFIG_TARGET_GE_BX50V3) += \ dtb-$(CONFIG_TARGET_GE_B1X5V2) += imx6dl-b1x5v2.dtb dtb-$(CONFIG_TARGET_MX53PPD) += imx53-ppd.dtb +# TODO(Linus Walleij <linus.walleij@linaro.org>): Should us a single vexpress +# Kconfig option to build all of these. See examples above. dtb-$(CONFIG_TARGET_VEXPRESS_CA9X4) += vexpress-v2p-ca9.dtb +dtb-$(CONFIG_TARGET_VEXPRESS64_JUNO) += juno-r2.dtb dtb-$(CONFIG_TARGET_TOTAL_COMPUTE) += total_compute.dtb @@ -1162,6 +1176,8 @@ dtb-$(CONFIG_TARGET_IMX8MM_CL_IOT_GATE_OPTEE) += imx8mm-cl-iot-gate-optee.dtb dtb-$(CONFIG_TARGET_EA_LPC3250DEVKITV2) += lpc3250-ea3250.dtb +dtb-$(CONFIG_ARCH_QEMU) += qemu-arm.dtb qemu-arm64.dtb + targets += $(dtb-y) # Add any required device tree compiler flags here diff --git a/arch/arm/dts/bcm2711-rpi-4-b.dts b/arch/arm/dts/bcm2711-rpi-4-b.dts new file mode 100644 index 0000000..72ce80f --- /dev/null +++ b/arch/arm/dts/bcm2711-rpi-4-b.dts @@ -0,0 +1,262 @@ +// SPDX-License-Identifier: GPL-2.0 +/dts-v1/; +#include "bcm2711.dtsi" +#include "bcm2711-rpi.dtsi" +#include "bcm283x-rpi-usb-peripheral.dtsi" + +/ { + compatible = "raspberrypi,4-model-b", "brcm,bcm2711"; + model = "Raspberry Pi 4 Model B"; + + chosen { + /* 8250 auxiliary UART instead of pl011 */ + stdout-path = "serial1:115200n8"; + }; + + leds { + led-act { + gpios = <&gpio 42 GPIO_ACTIVE_HIGH>; + }; + + led-pwr { + label = "PWR"; + gpios = <&expgpio 2 GPIO_ACTIVE_LOW>; + default-state = "keep"; + linux,default-trigger = "default-on"; + }; + }; + + wifi_pwrseq: wifi-pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>; + }; + + sd_io_1v8_reg: sd_io_1v8_reg { + compatible = "regulator-gpio"; + regulator-name = "vdd-sd-io"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + regulator-settling-time-us = <5000>; + gpios = <&expgpio 4 GPIO_ACTIVE_HIGH>; + states = <1800000 0x1>, + <3300000 0x0>; + status = "okay"; + }; + + sd_vcc_reg: sd_vcc_reg { + compatible = "regulator-fixed"; + regulator-name = "vcc-sd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + enable-active-high; + gpio = <&expgpio 6 GPIO_ACTIVE_HIGH>; + }; +}; + +&ddc0 { + status = "okay"; +}; + +&ddc1 { + status = "okay"; +}; + +&expgpio { + gpio-line-names = "BT_ON", + "WL_ON", + "PWR_LED_OFF", + "GLOBAL_RESET", + "VDD_SD_IO_SEL", + "CAM_GPIO", + "SD_PWR_ON", + ""; +}; + +&gpio { + /* + * Parts taken from rpi_SCH_4b_4p0_reduced.pdf and + * the official GPU firmware DT blob. + * + * Legend: + * "FOO" = GPIO line named "FOO" on the schematic + * "FOO_N" = GPIO line named "FOO" on schematic, active low + */ + gpio-line-names = "ID_SDA", + "ID_SCL", + "SDA1", + "SCL1", + "GPIO_GCLK", + "GPIO5", + "GPIO6", + "SPI_CE1_N", + "SPI_CE0_N", + "SPI_MISO", + "SPI_MOSI", + "SPI_SCLK", + "GPIO12", + "GPIO13", + /* Serial port */ + "TXD1", + "RXD1", + "GPIO16", + "GPIO17", + "GPIO18", + "GPIO19", + "GPIO20", + "GPIO21", + "GPIO22", + "GPIO23", + "GPIO24", + "GPIO25", + "GPIO26", + "GPIO27", + "RGMII_MDIO", + "RGMIO_MDC", + /* Used by BT module */ + "CTS0", + "RTS0", + "TXD0", + "RXD0", + /* Used by Wifi */ + "SD1_CLK", + "SD1_CMD", + "SD1_DATA0", + "SD1_DATA1", + "SD1_DATA2", + "SD1_DATA3", + /* Shared with SPI flash */ + "PWM0_MISO", + "PWM1_MOSI", + "STATUS_LED_G_CLK", + "SPIFLASH_CE_N", + "SDA0", + "SCL0", + "RGMII_RXCLK", + "RGMII_RXCTL", + "RGMII_RXD0", + "RGMII_RXD1", + "RGMII_RXD2", + "RGMII_RXD3", + "RGMII_TXCLK", + "RGMII_TXCTL", + "RGMII_TXD0", + "RGMII_TXD1", + "RGMII_TXD2", + "RGMII_TXD3"; +}; + +&hdmi0 { + status = "okay"; +}; + +&hdmi1 { + status = "okay"; +}; + +&pixelvalve0 { + status = "okay"; +}; + +&pixelvalve1 { + status = "okay"; +}; + +&pixelvalve2 { + status = "okay"; +}; + +&pixelvalve4 { + status = "okay"; +}; + +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pwm1_0_gpio40 &pwm1_1_gpio41>; + status = "okay"; +}; + +/* SDHCI is used to control the SDIO for wireless */ +&sdhci { + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_gpio34>; + bus-width = <4>; + non-removable; + mmc-pwrseq = <&wifi_pwrseq>; + status = "okay"; + + brcmf: wifi@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + }; +}; + +/* EMMC2 is used to drive the SD card */ +&emmc2 { + vqmmc-supply = <&sd_io_1v8_reg>; + vmmc-supply = <&sd_vcc_reg>; + broken-cd; + status = "okay"; +}; + +&genet { + phy-handle = <&phy1>; + phy-mode = "rgmii-rxid"; + status = "okay"; +}; + +&genet_mdio { + phy1: ethernet-phy@1 { + /* No PHY interrupt */ + reg = <0x1>; + }; +}; + +&pcie0 { + pci@0,0 { + device_type = "pci"; + #address-cells = <3>; + #size-cells = <2>; + ranges; + + reg = <0 0 0 0 0>; + + usb@0,0 { + reg = <0 0 0 0 0>; + resets = <&reset RASPBERRYPI_FIRMWARE_RESET_ID_USB>; + }; + }; +}; + +/* uart0 communicates with the BT module */ +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32>; + uart-has-rtscts; + status = "okay"; + + bluetooth { + compatible = "brcm,bcm43438-bt"; + max-speed = <2000000>; + shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>; + }; +}; + +/* uart1 is mapped to the pin header */ +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_gpio14>; + status = "okay"; +}; + +&vc4 { + status = "okay"; +}; + +&vec { + status = "disabled"; +}; diff --git a/arch/arm/dts/bcm2711-rpi.dtsi b/arch/arm/dts/bcm2711-rpi.dtsi new file mode 100644 index 0000000..ca266c5 --- /dev/null +++ b/arch/arm/dts/bcm2711-rpi.dtsi @@ -0,0 +1,74 @@ +// SPDX-License-Identifier: GPL-2.0 +#include "bcm2835-rpi.dtsi" + +#include <dt-bindings/reset/raspberrypi,firmware-reset.h> + +/ { + /* Will be filled by the bootloader */ + memory@0 { + device_type = "memory"; + reg = <0 0 0>; + }; + + aliases { + emmc2bus = &emmc2bus; + ethernet0 = &genet; + pcie0 = &pcie0; + blconfig = &blconfig; + }; +}; + +&firmware { + firmware_clocks: clocks { + compatible = "raspberrypi,firmware-clocks"; + #clock-cells = <1>; + }; + + expgpio: gpio { + compatible = "raspberrypi,firmware-gpio"; + gpio-controller; + #gpio-cells = <2>; + status = "okay"; + }; + + reset: reset { + compatible = "raspberrypi,firmware-reset"; + #reset-cells = <1>; + }; +}; + +&hdmi0 { + clocks = <&firmware_clocks 13>, <&firmware_clocks 14>, <&dvp 0>, <&clk_27MHz>; + clock-names = "hdmi", "bvb", "audio", "cec"; + wifi-2.4ghz-coexistence; +}; + +&hdmi1 { + clocks = <&firmware_clocks 13>, <&firmware_clocks 14>, <&dvp 1>, <&clk_27MHz>; + clock-names = "hdmi", "bvb", "audio", "cec"; + wifi-2.4ghz-coexistence; +}; + +&hvs { + clocks = <&firmware_clocks 4>; +}; + +&rmem { + /* + * RPi4's co-processor will copy the board's bootloader configuration + * into memory for the OS to consume. It'll also update this node with + * its placement information. + */ + blconfig: nvram@0 { + compatible = "raspberrypi,bootloader-config", "nvmem-rmem"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x0 0x0 0x0>; + no-map; + status = "disabled"; + }; +}; + +&vchiq { + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; +}; diff --git a/arch/arm/dts/bcm2711.dtsi b/arch/arm/dts/bcm2711.dtsi new file mode 100644 index 0000000..3b60297 --- /dev/null +++ b/arch/arm/dts/bcm2711.dtsi @@ -0,0 +1,1100 @@ +// SPDX-License-Identifier: GPL-2.0 +#include "bcm283x.dtsi" + +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/soc/bcm2835-pm.h> + +/ { + compatible = "brcm,bcm2711"; + + #address-cells = <2>; + #size-cells = <1>; + + interrupt-parent = <&gicv2>; + + vc4: gpu { + compatible = "brcm,bcm2711-vc5"; + status = "disabled"; + }; + + clk_27MHz: clk-27M { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <27000000>; + clock-output-names = "27MHz-clock"; + }; + + clk_108MHz: clk-108M { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <108000000>; + clock-output-names = "108MHz-clock"; + }; + + soc { + /* + * Defined ranges: + * Common BCM283x peripherals + * BCM2711-specific peripherals + * ARM-local peripherals + */ + ranges = <0x7e000000 0x0 0xfe000000 0x01800000>, + <0x7c000000 0x0 0xfc000000 0x02000000>, + <0x40000000 0x0 0xff800000 0x00800000>; + /* Emulate a contiguous 30-bit address range for DMA */ + dma-ranges = <0xc0000000 0x0 0x00000000 0x40000000>; + + /* + * This node is the provider for the enable-method for + * bringing up secondary cores. + */ + local_intc: local_intc@40000000 { + compatible = "brcm,bcm2836-l1-intc"; + reg = <0x40000000 0x100>; + }; + + gicv2: interrupt-controller@40041000 { + interrupt-controller; + #interrupt-cells = <3>; + compatible = "arm,gic-400"; + reg = <0x40041000 0x1000>, + <0x40042000 0x2000>, + <0x40044000 0x2000>, + <0x40046000 0x2000>; + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | + IRQ_TYPE_LEVEL_HIGH)>; + }; + + avs_monitor: avs-monitor@7d5d2000 { + compatible = "brcm,bcm2711-avs-monitor", + "syscon", "simple-mfd"; + reg = <0x7d5d2000 0xf00>; + + thermal: thermal { + compatible = "brcm,bcm2711-thermal"; + #thermal-sensor-cells = <0>; + }; + }; + + dma: dma@7e007000 { + compatible = "brcm,bcm2835-dma"; + reg = <0x7e007000 0xb00>; + interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>, + /* DMA lite 7 - 10 */ + <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "dma0", + "dma1", + "dma2", + "dma3", + "dma4", + "dma5", + "dma6", + "dma7", + "dma8", + "dma9", + "dma10"; + #dma-cells = <1>; + brcm,dma-channel-mask = <0x07f5>; + }; + + pm: watchdog@7e100000 { + compatible = "brcm,bcm2835-pm", "brcm,bcm2835-pm-wdt"; + #power-domain-cells = <1>; + #reset-cells = <1>; + reg = <0x7e100000 0x114>, + <0x7e00a000 0x24>, + <0x7ec11000 0x20>; + clocks = <&clocks BCM2835_CLOCK_V3D>, + <&clocks BCM2835_CLOCK_PERI_IMAGE>, + <&clocks BCM2835_CLOCK_H264>, + <&clocks BCM2835_CLOCK_ISP>; + clock-names = "v3d", "peri_image", "h264", "isp"; + system-power-controller; + }; + + rng@7e104000 { + compatible = "brcm,bcm2711-rng200"; + reg = <0x7e104000 0x28>; + }; + + uart2: serial@7e201400 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x7e201400 0x200>; + interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clocks BCM2835_CLOCK_UART>, + <&clocks BCM2835_CLOCK_VPU>; + clock-names = "uartclk", "apb_pclk"; + arm,primecell-periphid = <0x00241011>; + status = "disabled"; + }; + + uart3: serial@7e201600 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x7e201600 0x200>; + interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clocks BCM2835_CLOCK_UART>, + <&clocks BCM2835_CLOCK_VPU>; + clock-names = "uartclk", "apb_pclk"; + arm,primecell-periphid = <0x00241011>; + status = "disabled"; + }; + + uart4: serial@7e201800 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x7e201800 0x200>; + interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clocks BCM2835_CLOCK_UART>, + <&clocks BCM2835_CLOCK_VPU>; + clock-names = "uartclk", "apb_pclk"; + arm,primecell-periphid = <0x00241011>; + status = "disabled"; + }; + + uart5: serial@7e201a00 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x7e201a00 0x200>; + interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clocks BCM2835_CLOCK_UART>, + <&clocks BCM2835_CLOCK_VPU>; + clock-names = "uartclk", "apb_pclk"; + arm,primecell-periphid = <0x00241011>; + status = "disabled"; + }; + + spi3: spi@7e204600 { + compatible = "brcm,bcm2835-spi"; + reg = <0x7e204600 0x0200>; + interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clocks BCM2835_CLOCK_VPU>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + spi4: spi@7e204800 { + compatible = "brcm,bcm2835-spi"; + reg = <0x7e204800 0x0200>; + interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clocks BCM2835_CLOCK_VPU>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + spi5: spi@7e204a00 { + compatible = "brcm,bcm2835-spi"; + reg = <0x7e204a00 0x0200>; + interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clocks BCM2835_CLOCK_VPU>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + spi6: spi@7e204c00 { + compatible = "brcm,bcm2835-spi"; + reg = <0x7e204c00 0x0200>; + interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clocks BCM2835_CLOCK_VPU>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c3: i2c@7e205600 { + compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; + reg = <0x7e205600 0x200>; + interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clocks BCM2835_CLOCK_VPU>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c4: i2c@7e205800 { + compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; + reg = <0x7e205800 0x200>; + interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clocks BCM2835_CLOCK_VPU>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c5: i2c@7e205a00 { + compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; + reg = <0x7e205a00 0x200>; + interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clocks BCM2835_CLOCK_VPU>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c6: i2c@7e205c00 { + compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; + reg = <0x7e205c00 0x200>; + interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clocks BCM2835_CLOCK_VPU>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + pixelvalve0: pixelvalve@7e206000 { + compatible = "brcm,bcm2711-pixelvalve0"; + reg = <0x7e206000 0x100>; + interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + pixelvalve1: pixelvalve@7e207000 { + compatible = "brcm,bcm2711-pixelvalve1"; + reg = <0x7e207000 0x100>; + interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + pixelvalve2: pixelvalve@7e20a000 { + compatible = "brcm,bcm2711-pixelvalve2"; + reg = <0x7e20a000 0x100>; + interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + pwm1: pwm@7e20c800 { + compatible = "brcm,bcm2835-pwm"; + reg = <0x7e20c800 0x28>; + clocks = <&clocks BCM2835_CLOCK_PWM>; + assigned-clocks = <&clocks BCM2835_CLOCK_PWM>; + assigned-clock-rates = <10000000>; + #pwm-cells = <2>; + status = "disabled"; + }; + + pixelvalve4: pixelvalve@7e216000 { + compatible = "brcm,bcm2711-pixelvalve4"; + reg = <0x7e216000 0x100>; + interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + hvs: hvs@7e400000 { + compatible = "brcm,bcm2711-hvs"; + interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; + }; + + pixelvalve3: pixelvalve@7ec12000 { + compatible = "brcm,bcm2711-pixelvalve3"; + reg = <0x7ec12000 0x100>; + interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + vec: vec@7ec13000 { + compatible = "brcm,bcm2711-vec"; + reg = <0x7ec13000 0x1000>; + clocks = <&clocks BCM2835_CLOCK_VEC>; + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + dvp: clock@7ef00000 { + compatible = "brcm,brcm2711-dvp"; + reg = <0x7ef00000 0x10>; + clocks = <&clk_108MHz>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + aon_intr: interrupt-controller@7ef00100 { + compatible = "brcm,bcm2711-l2-intc", "brcm,l2-intc"; + reg = <0x7ef00100 0x30>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <1>; + }; + + hdmi0: hdmi@7ef00700 { + compatible = "brcm,bcm2711-hdmi0"; + reg = <0x7ef00700 0x300>, + <0x7ef00300 0x200>, + <0x7ef00f00 0x80>, + <0x7ef00f80 0x80>, + <0x7ef01b00 0x200>, + <0x7ef01f00 0x400>, + <0x7ef00200 0x80>, + <0x7ef04300 0x100>, + <0x7ef20000 0x100>; + reg-names = "hdmi", + "dvp", + "phy", + "rm", + "packet", + "metadata", + "csc", + "cec", + "hd"; + clock-names = "hdmi", "bvb", "audio", "cec"; + resets = <&dvp 0>; + interrupt-parent = <&aon_intr>; + interrupts = <0>, <1>, <2>, + <3>, <4>, <5>; + interrupt-names = "cec-tx", "cec-rx", "cec-low", + "wakeup", "hpd-connected", "hpd-removed"; + ddc = <&ddc0>; + dmas = <&dma 10>; + dma-names = "audio-rx"; + status = "disabled"; + }; + + ddc0: i2c@7ef04500 { + compatible = "brcm,bcm2711-hdmi-i2c"; + reg = <0x7ef04500 0x100>, <0x7ef00b00 0x300>; + reg-names = "bsc", "auto-i2c"; + clock-frequency = <97500>; + status = "disabled"; + }; + + hdmi1: hdmi@7ef05700 { + compatible = "brcm,bcm2711-hdmi1"; + reg = <0x7ef05700 0x300>, + <0x7ef05300 0x200>, + <0x7ef05f00 0x80>, + <0x7ef05f80 0x80>, + <0x7ef06b00 0x200>, + <0x7ef06f00 0x400>, + <0x7ef00280 0x80>, + <0x7ef09300 0x100>, + <0x7ef20000 0x100>; + reg-names = "hdmi", + "dvp", + "phy", + "rm", + "packet", + "metadata", + "csc", + "cec", + "hd"; + ddc = <&ddc1>; + clock-names = "hdmi", "bvb", "audio", "cec"; + resets = <&dvp 1>; + interrupt-parent = <&aon_intr>; + interrupts = <8>, <7>, <6>, + <9>, <10>, <11>; + interrupt-names = "cec-tx", "cec-rx", "cec-low", + "wakeup", "hpd-connected", "hpd-removed"; + dmas = <&dma 17>; + dma-names = "audio-rx"; + status = "disabled"; + }; + + ddc1: i2c@7ef09500 { + compatible = "brcm,bcm2711-hdmi-i2c"; + reg = <0x7ef09500 0x100>, <0x7ef05b00 0x300>; + reg-names = "bsc", "auto-i2c"; + clock-frequency = <97500>; + status = "disabled"; + }; + }; + + /* + * emmc2 has different DMA constraints based on SoC revisions. It was + * moved into its own bus, so as for RPi4's firmware to update them. + * The firmware will find whether the emmc2bus alias is defined, and if + * so, it'll edit the dma-ranges property below accordingly. + */ + emmc2bus: emmc2bus { + compatible = "simple-bus"; + #address-cells = <2>; + #size-cells = <1>; + + ranges = <0x0 0x7e000000 0x0 0xfe000000 0x01800000>; + dma-ranges = <0x0 0xc0000000 0x0 0x00000000 0x40000000>; + + emmc2: mmc@7e340000 { + compatible = "brcm,bcm2711-emmc2"; + reg = <0x0 0x7e340000 0x100>; + interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clocks BCM2711_CLOCK_EMMC2>; + status = "disabled"; + }; + }; + + arm-pmu { + compatible = "arm,cortex-a72-pmu", "arm,armv8-pmuv3"; + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>; + interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | + IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | + IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | + IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | + IRQ_TYPE_LEVEL_LOW)>; + /* This only applies to the ARMv7 stub */ + arm,cpu-registers-not-fw-configured; + }; + + cpus: cpus { + #address-cells = <1>; + #size-cells = <0>; + enable-method = "brcm,bcm2836-smp"; // for ARM 32-bit + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a72"; + reg = <0>; + enable-method = "spin-table"; + cpu-release-addr = <0x0 0x000000d8>; + }; + + cpu1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a72"; + reg = <1>; + enable-method = "spin-table"; + cpu-release-addr = <0x0 0x000000e0>; + }; + + cpu2: cpu@2 { + device_type = "cpu"; + compatible = "arm,cortex-a72"; + reg = <2>; + enable-method = "spin-table"; + cpu-release-addr = <0x0 0x000000e8>; + }; + + cpu3: cpu@3 { + device_type = "cpu"; + compatible = "arm,cortex-a72"; + reg = <3>; + enable-method = "spin-table"; + cpu-release-addr = <0x0 0x000000f0>; + }; + }; + + scb { + compatible = "simple-bus"; + #address-cells = <2>; + #size-cells = <1>; + + ranges = <0x0 0x7c000000 0x0 0xfc000000 0x03800000>, + <0x6 0x00000000 0x6 0x00000000 0x40000000>; + + pcie0: pcie@7d500000 { + compatible = "brcm,bcm2711-pcie"; + reg = <0x0 0x7d500000 0x9310>; + device_type = "pci"; + #address-cells = <3>; + #interrupt-cells = <1>; + #size-cells = <2>; + interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "pcie", "msi"; + interrupt-map-mask = <0x0 0x0 0x0 0x7>; + interrupt-map = <0 0 0 1 &gicv2 GIC_SPI 143 + IRQ_TYPE_LEVEL_HIGH>; + msi-controller; + msi-parent = <&pcie0>; + + ranges = <0x02000000 0x0 0xf8000000 0x6 0x00000000 + 0x0 0x04000000>; + /* + * The wrapper around the PCIe block has a bug + * preventing it from accessing beyond the first 3GB of + * memory. + */ + dma-ranges = <0x02000000 0x0 0x00000000 0x0 0x00000000 + 0x0 0xc0000000>; + brcm,enable-ssc; + }; + + genet: ethernet@7d580000 { + compatible = "brcm,bcm2711-genet-v5"; + reg = <0x0 0x7d580000 0x10000>; + #address-cells = <0x1>; + #size-cells = <0x1>; + interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + + genet_mdio: mdio@e14 { + compatible = "brcm,genet-mdio-v5"; + reg = <0xe14 0x8>; + reg-names = "mdio"; + #address-cells = <0x1>; + #size-cells = <0x0>; + }; + }; + }; +}; + +&clk_osc { + clock-frequency = <54000000>; +}; + +&clocks { + compatible = "brcm,bcm2711-cprman"; +}; + +&cpu_thermal { + coefficients = <(-487) 410040>; + thermal-sensors = <&thermal>; +}; + +&dsi0 { + interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; +}; + +&dsi1 { + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; + compatible = "brcm,bcm2711-dsi1"; +}; + +&gpio { + compatible = "brcm,bcm2711-gpio"; + interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>; + + gpclk0_gpio49: gpclk0_gpio49 { + pin-gpclk { + pins = "gpio49"; + function = "alt1"; + bias-disable; + }; + }; + gpclk1_gpio50: gpclk1_gpio50 { + pin-gpclk { + pins = "gpio50"; + function = "alt1"; + bias-disable; + }; + }; + gpclk2_gpio51: gpclk2_gpio51 { + pin-gpclk { + pins = "gpio51"; + function = "alt1"; + bias-disable; + }; + }; + + i2c0_gpio46: i2c0_gpio46 { + pin-sda { + function = "alt0"; + pins = "gpio46"; + bias-pull-up; + }; + pin-scl { + function = "alt0"; + pins = "gpio47"; + bias-disable; + }; + }; + i2c1_gpio46: i2c1_gpio46 { + pin-sda { + function = "alt1"; + pins = "gpio46"; + bias-pull-up; + }; + pin-scl { + function = "alt1"; + pins = "gpio47"; + bias-disable; + }; + }; + i2c3_gpio2: i2c3_gpio2 { + pin-sda { + function = "alt5"; + pins = "gpio2"; + bias-pull-up; + }; + pin-scl { + function = "alt5"; + pins = "gpio3"; + bias-disable; + }; + }; + i2c3_gpio4: i2c3_gpio4 { + pin-sda { + function = "alt5"; + pins = "gpio4"; + bias-pull-up; + }; + pin-scl { + function = "alt5"; + pins = "gpio5"; + bias-disable; + }; + }; + i2c4_gpio6: i2c4_gpio6 { + pin-sda { + function = "alt5"; + pins = "gpio6"; + bias-pull-up; + }; + pin-scl { + function = "alt5"; + pins = "gpio7"; + bias-disable; + }; + }; + i2c4_gpio8: i2c4_gpio8 { + pin-sda { + function = "alt5"; + pins = "gpio8"; + bias-pull-up; + }; + pin-scl { + function = "alt5"; + pins = "gpio9"; + bias-disable; + }; + }; + i2c5_gpio10: i2c5_gpio10 { + pin-sda { + function = "alt5"; + pins = "gpio10"; + bias-pull-up; + }; + pin-scl { + function = "alt5"; + pins = "gpio11"; + bias-disable; + }; + }; + i2c5_gpio12: i2c5_gpio12 { + pin-sda { + function = "alt5"; + pins = "gpio12"; + bias-pull-up; + }; + pin-scl { + function = "alt5"; + pins = "gpio13"; + bias-disable; + }; + }; + i2c6_gpio0: i2c6_gpio0 { + pin-sda { + function = "alt5"; + pins = "gpio0"; + bias-pull-up; + }; + pin-scl { + function = "alt5"; + pins = "gpio1"; + bias-disable; + }; + }; + i2c6_gpio22: i2c6_gpio22 { + pin-sda { + function = "alt5"; + pins = "gpio22"; + bias-pull-up; + }; + pin-scl { + function = "alt5"; + pins = "gpio23"; + bias-disable; + }; + }; + i2c_slave_gpio8: i2c_slave_gpio8 { + pins-i2c-slave { + pins = "gpio8", + "gpio9", + "gpio10", + "gpio11"; + function = "alt3"; + }; + }; + + jtag_gpio48: jtag_gpio48 { + pins-jtag { + pins = "gpio48", + "gpio49", + "gpio50", + "gpio51", + "gpio52", + "gpio53"; + function = "alt4"; + }; + }; + + mii_gpio28: mii_gpio28 { + pins-mii { + pins = "gpio28", + "gpio29", + "gpio30", + "gpio31"; + function = "alt4"; + }; + }; + mii_gpio36: mii_gpio36 { + pins-mii { + pins = "gpio36", + "gpio37", + "gpio38", + "gpio39"; + function = "alt5"; + }; + }; + + pcm_gpio50: pcm_gpio50 { + pins-pcm { + pins = "gpio50", + "gpio51", + "gpio52", + "gpio53"; + function = "alt2"; + }; + }; + + pwm0_0_gpio12: pwm0_0_gpio12 { + pin-pwm { + pins = "gpio12"; + function = "alt0"; + bias-disable; + }; + }; + pwm0_0_gpio18: pwm0_0_gpio18 { + pin-pwm { + pins = "gpio18"; + function = "alt5"; + bias-disable; + }; + }; + pwm1_0_gpio40: pwm1_0_gpio40 { + pin-pwm { + pins = "gpio40"; + function = "alt0"; + bias-disable; + }; + }; + pwm0_1_gpio13: pwm0_1_gpio13 { + pin-pwm { + pins = "gpio13"; + function = "alt0"; + bias-disable; + }; + }; + pwm0_1_gpio19: pwm0_1_gpio19 { + pin-pwm { + pins = "gpio19"; + function = "alt5"; + bias-disable; + }; + }; + pwm1_1_gpio41: pwm1_1_gpio41 { + pin-pwm { + pins = "gpio41"; + function = "alt0"; + bias-disable; + }; + }; + pwm0_1_gpio45: pwm0_1_gpio45 { + pin-pwm { + pins = "gpio45"; + function = "alt0"; + bias-disable; + }; + }; + pwm0_0_gpio52: pwm0_0_gpio52 { + pin-pwm { + pins = "gpio52"; + function = "alt1"; + bias-disable; + }; + }; + pwm0_1_gpio53: pwm0_1_gpio53 { + pin-pwm { + pins = "gpio53"; + function = "alt1"; + bias-disable; + }; + }; + + rgmii_gpio35: rgmii_gpio35 { + pin-start-stop { + pins = "gpio35"; + function = "alt4"; + }; + pin-rx-ok { + pins = "gpio36"; + function = "alt4"; + }; + }; + rgmii_irq_gpio34: rgmii_irq_gpio34 { + pin-irq { + pins = "gpio34"; + function = "alt5"; + }; + }; + rgmii_irq_gpio39: rgmii_irq_gpio39 { + pin-irq { + pins = "gpio39"; + function = "alt4"; + }; + }; + rgmii_mdio_gpio28: rgmii_mdio_gpio28 { + pins-mdio { + pins = "gpio28", + "gpio29"; + function = "alt5"; + }; + }; + rgmii_mdio_gpio37: rgmii_mdio_gpio37 { + pins-mdio { + pins = "gpio37", + "gpio38"; + function = "alt4"; + }; + }; + + spi0_gpio46: spi0_gpio46 { + pins-spi { + pins = "gpio46", + "gpio47", + "gpio48", + "gpio49"; + function = "alt2"; + }; + }; + spi2_gpio46: spi2_gpio46 { + pins-spi { + pins = "gpio46", + "gpio47", + "gpio48", + "gpio49", + "gpio50"; + function = "alt5"; + }; + }; + spi3_gpio0: spi3_gpio0 { + pins-spi { + pins = "gpio0", + "gpio1", + "gpio2", + "gpio3"; + function = "alt3"; + }; + }; + spi4_gpio4: spi4_gpio4 { + pins-spi { + pins = "gpio4", + "gpio5", + "gpio6", + "gpio7"; + function = "alt3"; + }; + }; + spi5_gpio12: spi5_gpio12 { + pins-spi { + pins = "gpio12", + "gpio13", + "gpio14", + "gpio15"; + function = "alt3"; + }; + }; + spi6_gpio18: spi6_gpio18 { + pins-spi { + pins = "gpio18", + "gpio19", + "gpio20", + "gpio21"; + function = "alt3"; + }; + }; + + uart2_gpio0: uart2_gpio0 { + pin-tx { + pins = "gpio0"; + function = "alt4"; + bias-disable; + }; + pin-rx { + pins = "gpio1"; + function = "alt4"; + bias-pull-up; + }; + }; + uart2_ctsrts_gpio2: uart2_ctsrts_gpio2 { + pin-cts { + pins = "gpio2"; + function = "alt4"; + bias-pull-up; + }; + pin-rts { + pins = "gpio3"; + function = "alt4"; + bias-disable; + }; + }; + uart3_gpio4: uart3_gpio4 { + pin-tx { + pins = "gpio4"; + function = "alt4"; + bias-disable; + }; + pin-rx { + pins = "gpio5"; + function = "alt4"; + bias-pull-up; + }; + }; + uart3_ctsrts_gpio6: uart3_ctsrts_gpio6 { + pin-cts { + pins = "gpio6"; + function = "alt4"; + bias-pull-up; + }; + pin-rts { + pins = "gpio7"; + function = "alt4"; + bias-disable; + }; + }; + uart4_gpio8: uart4_gpio8 { + pin-tx { + pins = "gpio8"; + function = "alt4"; + bias-disable; + }; + pin-rx { + pins = "gpio9"; + function = "alt4"; + bias-pull-up; + }; + }; + uart4_ctsrts_gpio10: uart4_ctsrts_gpio10 { + pin-cts { + pins = "gpio10"; + function = "alt4"; + bias-pull-up; + }; + pin-rts { + pins = "gpio11"; + function = "alt4"; + bias-disable; + }; + }; + uart5_gpio12: uart5_gpio12 { + pin-tx { + pins = "gpio12"; + function = "alt4"; + bias-disable; + }; + pin-rx { + pins = "gpio13"; + function = "alt4"; + bias-pull-up; + }; + }; + uart5_ctsrts_gpio14: uart5_ctsrts_gpio14 { + pin-cts { + pins = "gpio14"; + function = "alt4"; + bias-pull-up; + }; + pin-rts { + pins = "gpio15"; + function = "alt4"; + bias-disable; + }; + }; +}; + +&rmem { + #address-cells = <2>; +}; + +&cma { + /* + * arm64 reserves the CMA by default somewhere in ZONE_DMA32, + * that's not good enough for the BCM2711 as some devices can + * only address the lower 1G of memory (ZONE_DMA). + */ + alloc-ranges = <0x0 0x00000000 0x40000000>; +}; + +&i2c0 { + compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; + interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; +}; + +&i2c1 { + compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; + interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; +}; + +&mailbox { + interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; +}; + +&sdhci { + interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>; +}; + +&sdhost { + interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; +}; + +&spi { + interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; +}; + +&spi1 { + interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; +}; + +&spi2 { + interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; +}; + +&system_timer { + interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>; +}; + +&txp { + interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; +}; + +&uart0 { + interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; +}; + +&uart1 { + interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; +}; + +&usb { + interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; +}; + +&vec { + compatible = "brcm,bcm2711-vec"; + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; +}; diff --git a/arch/arm/dts/bcm2835-common.dtsi b/arch/arm/dts/bcm2835-common.dtsi new file mode 100644 index 0000000..c25e797 --- /dev/null +++ b/arch/arm/dts/bcm2835-common.dtsi @@ -0,0 +1,207 @@ +// SPDX-License-Identifier: GPL-2.0 + +/* This include file covers the common peripherals and configuration between + * bcm2835, bcm2836 and bcm2837 implementations. + */ + +/ { + interrupt-parent = <&intc>; + + soc { + dma: dma@7e007000 { + compatible = "brcm,bcm2835-dma"; + reg = <0x7e007000 0xf00>; + interrupts = <1 16>, + <1 17>, + <1 18>, + <1 19>, + <1 20>, + <1 21>, + <1 22>, + <1 23>, + <1 24>, + <1 25>, + <1 26>, + /* dma channel 11-14 share one irq */ + <1 27>, + <1 27>, + <1 27>, + <1 27>, + /* unused shared irq for all channels */ + <1 28>; + interrupt-names = "dma0", + "dma1", + "dma2", + "dma3", + "dma4", + "dma5", + "dma6", + "dma7", + "dma8", + "dma9", + "dma10", + "dma11", + "dma12", + "dma13", + "dma14", + "dma-shared-all"; + #dma-cells = <1>; + brcm,dma-channel-mask = <0x7f35>; + }; + + intc: interrupt-controller@7e00b200 { + compatible = "brcm,bcm2835-armctrl-ic"; + reg = <0x7e00b200 0x200>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + pm: watchdog@7e100000 { + compatible = "brcm,bcm2835-pm", "brcm,bcm2835-pm-wdt"; + #power-domain-cells = <1>; + #reset-cells = <1>; + reg = <0x7e100000 0x114>, + <0x7e00a000 0x24>; + clocks = <&clocks BCM2835_CLOCK_V3D>, + <&clocks BCM2835_CLOCK_PERI_IMAGE>, + <&clocks BCM2835_CLOCK_H264>, + <&clocks BCM2835_CLOCK_ISP>; + clock-names = "v3d", "peri_image", "h264", "isp"; + system-power-controller; + }; + + rng@7e104000 { + compatible = "brcm,bcm2835-rng"; + reg = <0x7e104000 0x10>; + interrupts = <2 29>; + }; + + pixelvalve@7e206000 { + compatible = "brcm,bcm2835-pixelvalve0"; + reg = <0x7e206000 0x100>; + interrupts = <2 13>; /* pwa0 */ + }; + + pixelvalve@7e207000 { + compatible = "brcm,bcm2835-pixelvalve1"; + reg = <0x7e207000 0x100>; + interrupts = <2 14>; /* pwa1 */ + }; + + thermal: thermal@7e212000 { + compatible = "brcm,bcm2835-thermal"; + reg = <0x7e212000 0x8>; + clocks = <&clocks BCM2835_CLOCK_TSENS>; + #thermal-sensor-cells = <0>; + status = "disabled"; + }; + + i2c2: i2c@7e805000 { + compatible = "brcm,bcm2835-i2c"; + reg = <0x7e805000 0x1000>; + interrupts = <2 21>; + clocks = <&clocks BCM2835_CLOCK_VPU>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + }; + + vec: vec@7e806000 { + compatible = "brcm,bcm2835-vec"; + reg = <0x7e806000 0x1000>; + clocks = <&clocks BCM2835_CLOCK_VEC>; + interrupts = <2 27>; + status = "disabled"; + }; + + pixelvalve@7e807000 { + compatible = "brcm,bcm2835-pixelvalve2"; + reg = <0x7e807000 0x100>; + interrupts = <2 10>; /* pixelvalve */ + }; + + hdmi: hdmi@7e902000 { + compatible = "brcm,bcm2835-hdmi"; + reg = <0x7e902000 0x600>, + <0x7e808000 0x100>; + interrupts = <2 8>, <2 9>; + ddc = <&i2c2>; + clocks = <&clocks BCM2835_PLLH_PIX>, + <&clocks BCM2835_CLOCK_HSM>; + clock-names = "pixel", "hdmi"; + dmas = <&dma 17>; + dma-names = "audio-rx"; + status = "disabled"; + }; + + v3d: v3d@7ec00000 { + compatible = "brcm,bcm2835-v3d"; + reg = <0x7ec00000 0x1000>; + interrupts = <1 10>; + }; + + vc4: gpu { + compatible = "brcm,bcm2835-vc4"; + }; + }; +}; + +&cpu_thermal { + thermal-sensors = <&thermal>; +}; + +&gpio { + i2c_slave_gpio18: i2c_slave_gpio18 { + brcm,pins = <18 19 20 21>; + brcm,function = <BCM2835_FSEL_ALT3>; + }; + + jtag_gpio4: jtag_gpio4 { + brcm,pins = <4 5 6 12 13>; + brcm,function = <BCM2835_FSEL_ALT5>; + }; + + pwm0_gpio12: pwm0_gpio12 { + brcm,pins = <12>; + brcm,function = <BCM2835_FSEL_ALT0>; + }; + pwm0_gpio18: pwm0_gpio18 { + brcm,pins = <18>; + brcm,function = <BCM2835_FSEL_ALT5>; + }; + pwm0_gpio40: pwm0_gpio40 { + brcm,pins = <40>; + brcm,function = <BCM2835_FSEL_ALT0>; + }; + pwm1_gpio13: pwm1_gpio13 { + brcm,pins = <13>; + brcm,function = <BCM2835_FSEL_ALT0>; + }; + pwm1_gpio19: pwm1_gpio19 { + brcm,pins = <19>; + brcm,function = <BCM2835_FSEL_ALT5>; + }; + pwm1_gpio41: pwm1_gpio41 { + brcm,pins = <41>; + brcm,function = <BCM2835_FSEL_ALT0>; + }; + pwm1_gpio45: pwm1_gpio45 { + brcm,pins = <45>; + brcm,function = <BCM2835_FSEL_ALT0>; + }; +}; + +&i2s { + dmas = <&dma 2>, <&dma 3>; + dma-names = "tx", "rx"; +}; + +&sdhost { + dmas = <&dma 13>; + dma-names = "rx-tx"; +}; + +&spi { + dmas = <&dma 6>, <&dma 7>; + dma-names = "tx", "rx"; +}; diff --git a/arch/arm/dts/bcm2835-rpi-a-plus.dts b/arch/arm/dts/bcm2835-rpi-a-plus.dts index db8a601..40b9405 100644 --- a/arch/arm/dts/bcm2835-rpi-a-plus.dts +++ b/arch/arm/dts/bcm2835-rpi-a-plus.dts @@ -8,12 +8,17 @@ compatible = "raspberrypi,model-a-plus", "brcm,bcm2835"; model = "Raspberry Pi Model A+"; + memory@0 { + device_type = "memory"; + reg = <0 0x10000000>; + }; + leds { - act { + led-act { gpios = <&gpio 47 GPIO_ACTIVE_HIGH>; }; - pwr { + led-pwr { label = "PWR"; gpios = <&gpio 35 GPIO_ACTIVE_HIGH>; default-state = "keep"; @@ -99,6 +104,8 @@ &hdmi { hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; + power-domains = <&power RPI_POWER_DOMAIN_HDMI>; + status = "okay"; }; &pwm { @@ -107,6 +114,13 @@ status = "okay"; }; +&sdhost { + pinctrl-names = "default"; + pinctrl-0 = <&sdhost_gpio48>; + bus-width = <4>; + status = "okay"; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_gpio14>; diff --git a/arch/arm/dts/bcm2835-rpi-a.dts b/arch/arm/dts/bcm2835-rpi-a.dts index 067d1f0..11edb58 100644 --- a/arch/arm/dts/bcm2835-rpi-a.dts +++ b/arch/arm/dts/bcm2835-rpi-a.dts @@ -8,8 +8,13 @@ compatible = "raspberrypi,model-a", "brcm,bcm2835"; model = "Raspberry Pi Model A"; + memory@0 { + device_type = "memory"; + reg = <0 0x10000000>; + }; + leds { - act { + led-act { gpios = <&gpio 16 GPIO_ACTIVE_LOW>; }; }; @@ -94,6 +99,8 @@ &hdmi { hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>; + power-domains = <&power RPI_POWER_DOMAIN_HDMI>; + status = "okay"; }; &pwm { @@ -102,6 +109,13 @@ status = "okay"; }; +&sdhost { + pinctrl-names = "default"; + pinctrl-0 = <&sdhost_gpio48>; + bus-width = <4>; + status = "okay"; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_gpio14>; diff --git a/arch/arm/dts/bcm2835-rpi-b-plus.dts b/arch/arm/dts/bcm2835-rpi-b-plus.dts index 1e40d67..1b435c6 100644 --- a/arch/arm/dts/bcm2835-rpi-b-plus.dts +++ b/arch/arm/dts/bcm2835-rpi-b-plus.dts @@ -9,12 +9,17 @@ compatible = "raspberrypi,model-b-plus", "brcm,bcm2835"; model = "Raspberry Pi Model B+"; + memory@0 { + device_type = "memory"; + reg = <0 0x20000000>; + }; + leds { - act { + led-act { gpios = <&gpio 47 GPIO_ACTIVE_HIGH>; }; - pwr { + led-pwr { label = "PWR"; gpios = <&gpio 35 GPIO_ACTIVE_HIGH>; default-state = "keep"; @@ -101,6 +106,8 @@ &hdmi { hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; + power-domains = <&power RPI_POWER_DOMAIN_HDMI>; + status = "okay"; }; &pwm { @@ -109,6 +116,13 @@ status = "okay"; }; +&sdhost { + pinctrl-names = "default"; + pinctrl-0 = <&sdhost_gpio48>; + bus-width = <4>; + status = "okay"; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_gpio14>; diff --git a/arch/arm/dts/bcm2835-rpi-b-rev2.dts b/arch/arm/dts/bcm2835-rpi-b-rev2.dts index 28e7513..a23c25c 100644 --- a/arch/arm/dts/bcm2835-rpi-b-rev2.dts +++ b/arch/arm/dts/bcm2835-rpi-b-rev2.dts @@ -9,8 +9,13 @@ compatible = "raspberrypi,model-b-rev2", "brcm,bcm2835"; model = "Raspberry Pi Model B rev2"; + memory@0 { + device_type = "memory"; + reg = <0 0x10000000>; + }; + leds { - act { + led-act { gpios = <&gpio 16 GPIO_ACTIVE_LOW>; }; }; @@ -94,6 +99,8 @@ &hdmi { hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>; + power-domains = <&power RPI_POWER_DOMAIN_HDMI>; + status = "okay"; }; &pwm { @@ -102,6 +109,13 @@ status = "okay"; }; +&sdhost { + pinctrl-names = "default"; + pinctrl-0 = <&sdhost_gpio48>; + bus-width = <4>; + status = "okay"; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_gpio14>; diff --git a/arch/arm/dts/bcm2835-rpi-b.dts b/arch/arm/dts/bcm2835-rpi-b.dts index 31ff602..1b63d6b 100644 --- a/arch/arm/dts/bcm2835-rpi-b.dts +++ b/arch/arm/dts/bcm2835-rpi-b.dts @@ -9,8 +9,13 @@ compatible = "raspberrypi,model-b", "brcm,bcm2835"; model = "Raspberry Pi Model B"; + memory@0 { + device_type = "memory"; + reg = <0 0x10000000>; + }; + leds { - act { + led-act { gpios = <&gpio 16 GPIO_ACTIVE_LOW>; }; }; @@ -89,6 +94,8 @@ &hdmi { hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>; + power-domains = <&power RPI_POWER_DOMAIN_HDMI>; + status = "okay"; }; &pwm { @@ -97,6 +104,13 @@ status = "okay"; }; +&sdhost { + pinctrl-names = "default"; + pinctrl-0 = <&sdhost_gpio48>; + bus-width = <4>; + status = "okay"; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_gpio14>; diff --git a/arch/arm/dts/bcm2835-rpi-cm1-io1.dts b/arch/arm/dts/bcm2835-rpi-cm1-io1.dts index 4764a25..a75c882 100644 --- a/arch/arm/dts/bcm2835-rpi-cm1-io1.dts +++ b/arch/arm/dts/bcm2835-rpi-cm1-io1.dts @@ -79,6 +79,15 @@ &hdmi { hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; + power-domains = <&power RPI_POWER_DOMAIN_HDMI>; + status = "okay"; +}; + +&sdhost { + pinctrl-names = "default"; + pinctrl-0 = <&sdhost_gpio48>; + bus-width = <4>; + status = "okay"; }; &uart0 { diff --git a/arch/arm/dts/bcm2835-rpi-cm1.dtsi b/arch/arm/dts/bcm2835-rpi-cm1.dtsi index ef22c2d..e4e6b6a 100644 --- a/arch/arm/dts/bcm2835-rpi-cm1.dtsi +++ b/arch/arm/dts/bcm2835-rpi-cm1.dtsi @@ -5,11 +5,16 @@ / { leds { - act { + led-act { gpios = <&gpio 47 GPIO_ACTIVE_LOW>; }; }; + memory@0 { + device_type = "memory"; + reg = <0 0x20000000>; + }; + reg_3v3: fixed-regulator { compatible = "regulator-fixed"; regulator-name = "3V3"; diff --git a/arch/arm/dts/bcm2835-rpi-common.dtsi b/arch/arm/dts/bcm2835-rpi-common.dtsi new file mode 100644 index 0000000..8a55b6c --- /dev/null +++ b/arch/arm/dts/bcm2835-rpi-common.dtsi @@ -0,0 +1,12 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * This include file covers the common peripherals and configuration between + * bcm2835, bcm2836 and bcm2837 implementations that interact with RPi's + * firmware interface. + */ + +#include <dt-bindings/power/raspberrypi-power.h> + +&v3d { + power-domains = <&power RPI_POWER_DOMAIN_V3D>; +}; diff --git a/arch/arm/dts/bcm2835-rpi-zero-w.dts b/arch/arm/dts/bcm2835-rpi-zero-w.dts index ba0167d..33b2b77 100644 --- a/arch/arm/dts/bcm2835-rpi-zero-w.dts +++ b/arch/arm/dts/bcm2835-rpi-zero-w.dts @@ -12,14 +12,19 @@ compatible = "raspberrypi,model-zero-w", "brcm,bcm2835"; model = "Raspberry Pi Zero W"; + memory@0 { + device_type = "memory"; + reg = <0 0x20000000>; + }; + chosen { /* 8250 auxiliary UART instead of pl011 */ stdout-path = "serial1:115200n8"; }; leds { - act { - gpios = <&gpio 47 GPIO_ACTIVE_HIGH>; + led-act { + gpios = <&gpio 47 GPIO_ACTIVE_LOW>; }; }; @@ -100,12 +105,16 @@ &hdmi { hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; + power-domains = <&power RPI_POWER_DOMAIN_HDMI>; + status = "okay"; }; &sdhci { #address-cells = <1>; #size-cells = <0>; + pinctrl-names = "default"; pinctrl-0 = <&emmc_gpio34 &gpclk2_gpio43>; + bus-width = <4>; mmc-pwrseq = <&wifi_pwrseq>; non-removable; status = "okay"; @@ -116,6 +125,13 @@ }; }; +&sdhost { + pinctrl-names = "default"; + pinctrl-0 = <&sdhost_gpio48>; + bus-width = <4>; + status = "okay"; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_gpio32 &uart0_ctsrts_gpio30>; diff --git a/arch/arm/dts/bcm2835-rpi-zero.dts b/arch/arm/dts/bcm2835-rpi-zero.dts index 3b35a8a..6f9b3a9 100644 --- a/arch/arm/dts/bcm2835-rpi-zero.dts +++ b/arch/arm/dts/bcm2835-rpi-zero.dts @@ -12,8 +12,13 @@ compatible = "raspberrypi,model-zero", "brcm,bcm2835"; model = "Raspberry Pi Zero"; + memory@0 { + device_type = "memory"; + reg = <0 0x20000000>; + }; + leds { - act { + led-act { gpios = <&gpio 47 GPIO_ACTIVE_HIGH>; }; }; @@ -96,6 +101,15 @@ &hdmi { hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; + power-domains = <&power RPI_POWER_DOMAIN_HDMI>; + status = "okay"; +}; + +&sdhost { + pinctrl-names = "default"; + pinctrl-0 = <&sdhost_gpio48>; + bus-width = <4>; + status = "okay"; }; &uart0 { diff --git a/arch/arm/dts/bcm2835-rpi.dtsi b/arch/arm/dts/bcm2835-rpi.dtsi index 715d50c..87ddcad 100644 --- a/arch/arm/dts/bcm2835-rpi.dtsi +++ b/arch/arm/dts/bcm2835-rpi.dtsi @@ -1,15 +1,10 @@ #include <dt-bindings/power/raspberrypi-power.h> / { - memory@0 { - device_type = "memory"; - reg = <0 0x10000000>; - }; - leds { compatible = "gpio-leds"; - act { + led-act { label = "ACT"; default-state = "keep"; linux,default-trigger = "heartbeat"; @@ -18,8 +13,12 @@ soc { firmware: firmware { - compatible = "raspberrypi,bcm2835-firmware", "simple-bus"; + compatible = "raspberrypi,bcm2835-firmware", "simple-mfd"; + #address-cells = <1>; + #size-cells = <1>; + mboxes = <&mailbox>; + dma-ranges; }; power: power { @@ -64,32 +63,10 @@ clock-frequency = <100000>; }; -&i2c2 { - status = "okay"; -}; - -&sdhci { - pinctrl-names = "default"; - pinctrl-0 = <&emmc_gpio48>; - bus-width = <4>; -}; - -&sdhost { - pinctrl-names = "default"; - pinctrl-0 = <&sdhost_gpio48>; - status = "okay"; - bus-width = <4>; -}; - &usb { power-domains = <&power RPI_POWER_DOMAIN_USB>; }; -&hdmi { - power-domains = <&power RPI_POWER_DOMAIN_HDMI>; - status = "okay"; -}; - &vec { power-domains = <&power RPI_POWER_DOMAIN_VEC>; status = "okay"; diff --git a/arch/arm/dts/bcm2835.dtsi b/arch/arm/dts/bcm2835.dtsi index a5c3824..0549686 100644 --- a/arch/arm/dts/bcm2835.dtsi +++ b/arch/arm/dts/bcm2835.dtsi @@ -1,5 +1,7 @@ // SPDX-License-Identifier: GPL-2.0 #include "bcm283x.dtsi" +#include "bcm2835-common.dtsi" +#include "bcm2835-rpi-common.dtsi" / { compatible = "brcm,bcm2835"; diff --git a/arch/arm/dts/bcm2836-rpi-2-b.dts b/arch/arm/dts/bcm2836-rpi-2-b.dts index 7b4e651..d8af8ee 100644 --- a/arch/arm/dts/bcm2836-rpi-2-b.dts +++ b/arch/arm/dts/bcm2836-rpi-2-b.dts @@ -10,15 +10,16 @@ model = "Raspberry Pi 2 Model B"; memory@0 { + device_type = "memory"; reg = <0 0x40000000>; }; leds { - act { + led-act { gpios = <&gpio 47 GPIO_ACTIVE_HIGH>; }; - pwr { + led-pwr { label = "PWR"; gpios = <&gpio 35 GPIO_ACTIVE_HIGH>; default-state = "keep"; @@ -105,6 +106,8 @@ &hdmi { hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; + power-domains = <&power RPI_POWER_DOMAIN_HDMI>; + status = "okay"; }; &pwm { @@ -113,6 +116,13 @@ status = "okay"; }; +&sdhost { + pinctrl-names = "default"; + pinctrl-0 = <&sdhost_gpio48>; + bus-width = <4>; + status = "okay"; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_gpio14>; diff --git a/arch/arm/dts/bcm2836.dtsi b/arch/arm/dts/bcm2836.dtsi index c933e84..b390006 100644 --- a/arch/arm/dts/bcm2836.dtsi +++ b/arch/arm/dts/bcm2836.dtsi @@ -1,5 +1,7 @@ // SPDX-License-Identifier: GPL-2.0 #include "bcm283x.dtsi" +#include "bcm2835-common.dtsi" +#include "bcm2835-rpi-common.dtsi" / { compatible = "brcm,bcm2836"; diff --git a/arch/arm/dts/bcm2837-rpi-3-a-plus.dts b/arch/arm/dts/bcm2837-rpi-3-a-plus.dts index 7f4437a..77099a7 100644 --- a/arch/arm/dts/bcm2837-rpi-3-a-plus.dts +++ b/arch/arm/dts/bcm2837-rpi-3-a-plus.dts @@ -14,17 +14,20 @@ }; memory@0 { + device_type = "memory"; reg = <0 0x20000000>; }; leds { - act { + led-act { gpios = <&gpio 29 GPIO_ACTIVE_HIGH>; }; - pwr { + led-pwr { label = "PWR"; gpios = <&expgpio 2 GPIO_ACTIVE_LOW>; + default-state = "keep"; + linux,default-trigger = "default-on"; }; }; }; @@ -117,6 +120,8 @@ &hdmi { hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>; + power-domains = <&power RPI_POWER_DOMAIN_HDMI>; + status = "okay"; }; &pwm { diff --git a/arch/arm/dts/bcm2837-rpi-3-b-plus.dts b/arch/arm/dts/bcm2837-rpi-3-b-plus.dts index c6fa34c..6101026 100644 --- a/arch/arm/dts/bcm2837-rpi-3-b-plus.dts +++ b/arch/arm/dts/bcm2837-rpi-3-b-plus.dts @@ -15,17 +15,20 @@ }; memory@0 { + device_type = "memory"; reg = <0 0x40000000>; }; leds { - act { + led-act { gpios = <&gpio 29 GPIO_ACTIVE_HIGH>; }; - pwr { + led-pwr { label = "PWR"; gpios = <&expgpio 2 GPIO_ACTIVE_LOW>; + default-state = "keep"; + linux,default-trigger = "default-on"; }; }; @@ -124,6 +127,8 @@ &hdmi { hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>; + power-domains = <&power RPI_POWER_DOMAIN_HDMI>; + status = "okay"; }; &pwm { diff --git a/arch/arm/dts/bcm2837-rpi-3-b.dts b/arch/arm/dts/bcm2837-rpi-3-b.dts index ce71f57..dd4a486 100644 --- a/arch/arm/dts/bcm2837-rpi-3-b.dts +++ b/arch/arm/dts/bcm2837-rpi-3-b.dts @@ -15,11 +15,12 @@ }; memory@0 { + device_type = "memory"; reg = <0 0x40000000>; }; leds { - act { + led-act { gpios = <&expgpio 2 GPIO_ACTIVE_HIGH>; }; }; @@ -125,6 +126,8 @@ &hdmi { hpd-gpios = <&expgpio 4 GPIO_ACTIVE_LOW>; + power-domains = <&power RPI_POWER_DOMAIN_HDMI>; + status = "okay"; }; /* uart0 communicates with the BT module */ diff --git a/arch/arm/dts/bcm2837-rpi-cm3-io3.dts b/arch/arm/dts/bcm2837-rpi-cm3-io3.dts index 6c8233a..588d941 100644 --- a/arch/arm/dts/bcm2837-rpi-cm3-io3.dts +++ b/arch/arm/dts/bcm2837-rpi-cm3-io3.dts @@ -78,6 +78,15 @@ &hdmi { hpd-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>; + power-domains = <&power RPI_POWER_DOMAIN_HDMI>; + status = "okay"; +}; + +&sdhost { + pinctrl-names = "default"; + pinctrl-0 = <&sdhost_gpio48>; + bus-width = <4>; + status = "okay"; }; &uart0 { diff --git a/arch/arm/dts/bcm2837-rpi-cm3.dtsi b/arch/arm/dts/bcm2837-rpi-cm3.dtsi index 81399b2..828a205 100644 --- a/arch/arm/dts/bcm2837-rpi-cm3.dtsi +++ b/arch/arm/dts/bcm2837-rpi-cm3.dtsi @@ -5,9 +5,18 @@ / { memory@0 { + device_type = "memory"; reg = <0 0x40000000>; }; + leds { + /* + * Since there is no upstream GPIO driver yet, + * remove the incomplete node. + */ + /delete-node/ led-act; + }; + reg_3v3: fixed-regulator { compatible = "regulator-fixed"; regulator-name = "3V3"; diff --git a/arch/arm/dts/bcm2837.dtsi b/arch/arm/dts/bcm2837.dtsi index beb6c50..0199ec9 100644 --- a/arch/arm/dts/bcm2837.dtsi +++ b/arch/arm/dts/bcm2837.dtsi @@ -1,4 +1,6 @@ #include "bcm283x.dtsi" +#include "bcm2835-common.dtsi" +#include "bcm2835-rpi-common.dtsi" / { compatible = "brcm,bcm2837"; diff --git a/arch/arm/dts/bcm283x-rpi-usb-peripheral.dtsi b/arch/arm/dts/bcm283x-rpi-usb-peripheral.dtsi new file mode 100644 index 0000000..0ff0e9e --- /dev/null +++ b/arch/arm/dts/bcm283x-rpi-usb-peripheral.dtsi @@ -0,0 +1,7 @@ +// SPDX-License-Identifier: GPL-2.0 +&usb { + dr_mode = "peripheral"; + g-rx-fifo-size = <256>; + g-np-tx-fifo-size = <32>; + g-tx-fifo-size = <256 256 512 512 512 768 768>; +}; diff --git a/arch/arm/dts/bcm283x.dtsi b/arch/arm/dts/bcm283x.dtsi index 9777644..a3e06b6 100644 --- a/arch/arm/dts/bcm283x.dtsi +++ b/arch/arm/dts/bcm283x.dtsi @@ -18,7 +18,6 @@ / { compatible = "brcm,bcm2835"; model = "BCM2835"; - interrupt-parent = <&intc>; #address-cells = <1>; #size-cells = <1>; @@ -31,16 +30,27 @@ stdout-path = "serial0:115200n8"; }; + rmem: reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + cma: linux,cma { + compatible = "shared-dma-pool"; + size = <0x4000000>; /* 64MB */ + reusable; + linux,cma-default; + }; + }; + thermal-zones { cpu_thermal: cpu-thermal { polling-delay-passive = <0>; polling-delay = <1000>; - thermal-sensors = <&thermal>; - trips { cpu-crit { - temperature = <80000>; + temperature = <90000>; hysteresis = <0>; type = "critical"; }; @@ -56,7 +66,7 @@ #address-cells = <1>; #size-cells = <1>; - timer@7e003000 { + system_timer: timer@7e003000 { compatible = "brcm,bcm2835-system-timer"; reg = <0x7e003000 0x1000>; interrupts = <1 0>, <1 1>, <1 2>, <1 3>; @@ -67,74 +77,12 @@ clock-frequency = <1000000>; }; - txp@7e004000 { + txp: txp@7e004000 { compatible = "brcm,bcm2835-txp"; reg = <0x7e004000 0x20>; interrupts = <1 11>; }; - dma: dma@7e007000 { - compatible = "brcm,bcm2835-dma"; - reg = <0x7e007000 0xf00>; - interrupts = <1 16>, - <1 17>, - <1 18>, - <1 19>, - <1 20>, - <1 21>, - <1 22>, - <1 23>, - <1 24>, - <1 25>, - <1 26>, - /* dma channel 11-14 share one irq */ - <1 27>, - <1 27>, - <1 27>, - <1 27>, - /* unused shared irq for all channels */ - <1 28>; - interrupt-names = "dma0", - "dma1", - "dma2", - "dma3", - "dma4", - "dma5", - "dma6", - "dma7", - "dma8", - "dma9", - "dma10", - "dma11", - "dma12", - "dma13", - "dma14", - "dma-shared-all"; - #dma-cells = <1>; - brcm,dma-channel-mask = <0x7f35>; - }; - - intc: interrupt-controller@7e00b200 { - compatible = "brcm,bcm2835-armctrl-ic"; - reg = <0x7e00b200 0x200>; - interrupt-controller; - #interrupt-cells = <2>; - }; - - pm: watchdog@7e100000 { - compatible = "brcm,bcm2835-pm", "brcm,bcm2835-pm-wdt"; - #power-domain-cells = <1>; - #reset-cells = <1>; - reg = <0x7e100000 0x114>, - <0x7e00a000 0x24>; - clocks = <&clocks BCM2835_CLOCK_V3D>, - <&clocks BCM2835_CLOCK_PERI_IMAGE>, - <&clocks BCM2835_CLOCK_H264>, - <&clocks BCM2835_CLOCK_ISP>; - clock-names = "v3d", "peri_image", "h264", "isp"; - system-power-controller; - }; - clocks: cprman@7e101000 { compatible = "brcm,bcm2835-cprman"; #clock-cells = <1>; @@ -149,12 +97,6 @@ <&dsi1 0>, <&dsi1 1>, <&dsi1 2>; }; - rng@7e104000 { - compatible = "brcm,bcm2835-rng"; - reg = <0x7e104000 0x10>; - interrupts = <2 29>; - }; - mailbox: mailbox@7e00b880 { compatible = "brcm,bcm2835-mbox"; reg = <0x7e00b880 0x40>; @@ -184,8 +126,7 @@ interrupt-controller; #interrupt-cells = <2>; - /* Defines pin muxing groups according to - * BCM2835-ARM-Peripherals.pdf page 102. + /* Defines common pin muxing groups * * While each pin can have its mux selected * for various functions individually, some @@ -263,15 +204,7 @@ brcm,pins = <44 45>; brcm,function = <BCM2835_FSEL_ALT2>; }; - i2c_slave_gpio18: i2c_slave_gpio18 { - brcm,pins = <18 19 20 21>; - brcm,function = <BCM2835_FSEL_ALT3>; - }; - jtag_gpio4: jtag_gpio4 { - brcm,pins = <4 5 6 12 13>; - brcm,function = <BCM2835_FSEL_ALT5>; - }; jtag_gpio22: jtag_gpio22 { brcm,pins = <22 23 24 25 26 27>; brcm,function = <BCM2835_FSEL_ALT4>; @@ -286,35 +219,6 @@ brcm,function = <BCM2835_FSEL_ALT2>; }; - pwm0_gpio12: pwm0_gpio12 { - brcm,pins = <12>; - brcm,function = <BCM2835_FSEL_ALT0>; - }; - pwm0_gpio18: pwm0_gpio18 { - brcm,pins = <18>; - brcm,function = <BCM2835_FSEL_ALT5>; - }; - pwm0_gpio40: pwm0_gpio40 { - brcm,pins = <40>; - brcm,function = <BCM2835_FSEL_ALT0>; - }; - pwm1_gpio13: pwm1_gpio13 { - brcm,pins = <13>; - brcm,function = <BCM2835_FSEL_ALT0>; - }; - pwm1_gpio19: pwm1_gpio19 { - brcm,pins = <19>; - brcm,function = <BCM2835_FSEL_ALT5>; - }; - pwm1_gpio41: pwm1_gpio41 { - brcm,pins = <41>; - brcm,function = <BCM2835_FSEL_ALT0>; - }; - pwm1_gpio45: pwm1_gpio45 { - brcm,pins = <45>; - brcm,function = <BCM2835_FSEL_ALT0>; - }; - sdhost_gpio48: sdhost_gpio48 { brcm,pins = <48 49 50 51 52 53>; brcm,function = <BCM2835_FSEL_ALT0>; @@ -396,8 +300,8 @@ }; uart0: serial@7e201000 { - compatible = "brcm,bcm2835-pl011", "arm,pl011", "arm,primecell"; - reg = <0x7e201000 0x1000>; + compatible = "arm,pl011", "arm,primecell"; + reg = <0x7e201000 0x200>; interrupts = <2 25>; clocks = <&clocks BCM2835_CLOCK_UART>, <&clocks BCM2835_CLOCK_VPU>; @@ -410,8 +314,6 @@ reg = <0x7e202000 0x100>; interrupts = <2 24>; clocks = <&clocks BCM2835_CLOCK_VPU>; - dmas = <&dma 13>; - dma-names = "rx-tx"; status = "disabled"; }; @@ -419,16 +321,12 @@ compatible = "brcm,bcm2835-i2s"; reg = <0x7e203000 0x24>; clocks = <&clocks BCM2835_CLOCK_PCM>; - - dmas = <&dma 2>, - <&dma 3>; - dma-names = "tx", "rx"; status = "disabled"; }; spi: spi@7e204000 { compatible = "brcm,bcm2835-spi"; - reg = <0x7e204000 0x1000>; + reg = <0x7e204000 0x200>; interrupts = <2 22>; clocks = <&clocks BCM2835_CLOCK_VPU>; #address-cells = <1>; @@ -438,7 +336,7 @@ i2c0: i2c@7e205000 { compatible = "brcm,bcm2835-i2c"; - reg = <0x7e205000 0x1000>; + reg = <0x7e205000 0x200>; interrupts = <2 21>; clocks = <&clocks BCM2835_CLOCK_VPU>; #address-cells = <1>; @@ -446,18 +344,6 @@ status = "disabled"; }; - pixelvalve@7e206000 { - compatible = "brcm,bcm2835-pixelvalve0"; - reg = <0x7e206000 0x100>; - interrupts = <2 13>; /* pwa0 */ - }; - - pixelvalve@7e207000 { - compatible = "brcm,bcm2835-pixelvalve1"; - reg = <0x7e207000 0x100>; - interrupts = <2 14>; /* pwa1 */ - }; - dpi: dpi@7e208000 { compatible = "brcm,bcm2835-dpi"; reg = <0x7e208000 0x8c>; @@ -486,13 +372,6 @@ "dsi0_ddr2", "dsi0_ddr"; - }; - - thermal: thermal@7e212000 { - compatible = "brcm,bcm2835-thermal"; - reg = <0x7e212000 0x8>; - clocks = <&clocks BCM2835_CLOCK_TSENS>; - #thermal-sensor-cells = <0>; status = "disabled"; }; @@ -541,7 +420,7 @@ status = "disabled"; }; - sdhci: sdhci@7e300000 { + sdhci: mmc@7e300000 { compatible = "brcm,bcm2835-sdhci"; reg = <0x7e300000 0x100>; interrupts = <2 30>; @@ -585,44 +464,6 @@ status = "disabled"; }; - i2c2: i2c@7e805000 { - compatible = "brcm,bcm2835-i2c"; - reg = <0x7e805000 0x1000>; - interrupts = <2 21>; - clocks = <&clocks BCM2835_CLOCK_VPU>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - vec: vec@7e806000 { - compatible = "brcm,bcm2835-vec"; - reg = <0x7e806000 0x1000>; - clocks = <&clocks BCM2835_CLOCK_VEC>; - interrupts = <2 27>; - status = "disabled"; - }; - - pixelvalve@7e807000 { - compatible = "brcm,bcm2835-pixelvalve2"; - reg = <0x7e807000 0x100>; - interrupts = <2 10>; /* pixelvalve */ - }; - - hdmi: hdmi@7e902000 { - compatible = "brcm,bcm2835-hdmi"; - reg = <0x7e902000 0x600>, - <0x7e808000 0x100>; - interrupts = <2 8>, <2 9>; - ddc = <&i2c2>; - clocks = <&clocks BCM2835_PLLH_PIX>, - <&clocks BCM2835_CLOCK_HSM>; - clock-names = "pixel", "hdmi"; - dmas = <&dma 17>; - dma-names = "audio-rx"; - status = "disabled"; - }; - usb: usb@7e980000 { compatible = "brcm,bcm2835-usb"; reg = <0x7e980000 0x10000>; @@ -634,36 +475,19 @@ phys = <&usbphy>; phy-names = "usb2-phy"; }; - - v3d: v3d@7ec00000 { - compatible = "brcm,bcm2835-v3d"; - reg = <0x7ec00000 0x1000>; - interrupts = <1 10>; - power-domains = <&pm BCM2835_POWER_DOMAIN_GRAFX_V3D>; - }; - - vc4: gpu { - compatible = "brcm,bcm2835-vc4"; - }; }; clocks { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <0>; - /* The oscillator is the root of the clock tree. */ - clk_osc: clock@3 { + clk_osc: clk-osc { compatible = "fixed-clock"; - reg = <3>; #clock-cells = <0>; clock-output-names = "osc"; clock-frequency = <19200000>; }; - clk_usb: clock@4 { + clk_usb: clk-usb { compatible = "fixed-clock"; - reg = <4>; #clock-cells = <0>; clock-output-names = "otg"; clock-frequency = <480000000>; diff --git a/arch/arm/dts/bcm7xxx.dts b/arch/arm/dts/bcm7xxx.dts new file mode 100644 index 0000000..786ce3f --- /dev/null +++ b/arch/arm/dts/bcm7xxx.dts @@ -0,0 +1,15 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Empty devicetre file for bcm7260 board + * + * This is required to make the board build with CONFIG OF_SEPARATE + * In-tree document explains how to obtain a real devicetree using 'bolt' but + * I did not attempt this. + * + * Copyright 2021 Google LLC + */ + +/dts-v1/; + +/ { +}; diff --git a/arch/arm/dts/highbank.dts b/arch/arm/dts/highbank.dts new file mode 100644 index 0000000..1480bad --- /dev/null +++ b/arch/arm/dts/highbank.dts @@ -0,0 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Empty devicetree for highbank/midway + */ + +/dts-v1/; + +/ { +}; diff --git a/arch/arm/dts/juno-base.dtsi b/arch/arm/dts/juno-base.dtsi new file mode 100644 index 0000000..6288e10 --- /dev/null +++ b/arch/arm/dts/juno-base.dtsi @@ -0,0 +1,831 @@ +// SPDX-License-Identifier: GPL-2.0 +#include "juno-clocks.dtsi" +#include "juno-motherboard.dtsi" + +/ { + /* + * Devices shared by all Juno boards + */ + + memtimer: timer@2a810000 { + compatible = "arm,armv7-timer-mem"; + reg = <0x0 0x2a810000 0x0 0x10000>; + clock-frequency = <50000000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x0 0x2a820000 0x20000>; + status = "disabled"; + frame@2a830000 { + frame-number = <1>; + interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x10000 0x10000>; + }; + }; + + mailbox: mhu@2b1f0000 { + compatible = "arm,mhu", "arm,primecell"; + reg = <0x0 0x2b1f0000 0x0 0x1000>; + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; + #mbox-cells = <1>; + clocks = <&soc_refclk100mhz>; + clock-names = "apb_pclk"; + }; + + smmu_gpu: iommu@2b400000 { + compatible = "arm,mmu-400", "arm,smmu-v1"; + reg = <0x0 0x2b400000 0x0 0x10000>; + interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + #global-interrupts = <1>; + power-domains = <&scpi_devpd 1>; + dma-coherent; + status = "disabled"; + }; + + smmu_pcie: iommu@2b500000 { + compatible = "arm,mmu-401", "arm,smmu-v1"; + reg = <0x0 0x2b500000 0x0 0x10000>; + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + #global-interrupts = <1>; + dma-coherent; + status = "disabled"; + }; + + smmu_etr: iommu@2b600000 { + compatible = "arm,mmu-401", "arm,smmu-v1"; + reg = <0x0 0x2b600000 0x0 0x10000>; + interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + #global-interrupts = <1>; + dma-coherent; + power-domains = <&scpi_devpd 0>; + }; + + gic: interrupt-controller@2c010000 { + compatible = "arm,gic-400", "arm,cortex-a15-gic"; + reg = <0x0 0x2c010000 0 0x1000>, + <0x0 0x2c02f000 0 0x2000>, + <0x0 0x2c04f000 0 0x2000>, + <0x0 0x2c06f000 0 0x2000>; + #address-cells = <1>; + #interrupt-cells = <3>; + #size-cells = <1>; + interrupt-controller; + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_HIGH)>; + ranges = <0 0 0x2c1c0000 0x40000>; + + v2m_0: v2m@0 { + compatible = "arm,gic-v2m-frame"; + msi-controller; + reg = <0 0x10000>; + }; + + v2m@10000 { + compatible = "arm,gic-v2m-frame"; + msi-controller; + reg = <0x10000 0x10000>; + }; + + v2m@20000 { + compatible = "arm,gic-v2m-frame"; + msi-controller; + reg = <0x20000 0x10000>; + }; + + v2m@30000 { + compatible = "arm,gic-v2m-frame"; + msi-controller; + reg = <0x30000 0x10000>; + }; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>; + }; + + /* + * Juno TRMs specify the size for these coresight components as 64K. + * The actual size is just 4K though 64K is reserved. Access to the + * unmapped reserved region results in a DECERR response. + */ + etf@20010000 { /* etf0 */ + compatible = "arm,coresight-tmc", "arm,primecell"; + reg = <0 0x20010000 0 0x1000>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + + in-ports { + port { + etf0_in_port: endpoint { + remote-endpoint = <&main_funnel_out_port>; + }; + }; + }; + + out-ports { + port { + etf0_out_port: endpoint { + }; + }; + }; + }; + + tpiu@20030000 { + compatible = "arm,coresight-tpiu", "arm,primecell"; + reg = <0 0x20030000 0 0x1000>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + in-ports { + port { + tpiu_in_port: endpoint { + remote-endpoint = <&replicator_out_port0>; + }; + }; + }; + }; + + /* main funnel on Juno r0, cssys0 funnel on Juno r1/r2 as per TRM*/ + main_funnel: funnel@20040000 { + compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; + reg = <0 0x20040000 0 0x1000>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + + out-ports { + port { + main_funnel_out_port: endpoint { + remote-endpoint = <&etf0_in_port>; + }; + }; + }; + + main_funnel_in_ports: in-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + main_funnel_in_port0: endpoint { + remote-endpoint = <&cluster0_funnel_out_port>; + }; + }; + + port@1 { + reg = <1>; + main_funnel_in_port1: endpoint { + remote-endpoint = <&cluster1_funnel_out_port>; + }; + }; + }; + }; + + etr@20070000 { + compatible = "arm,coresight-tmc", "arm,primecell"; + reg = <0 0x20070000 0 0x1000>; + iommus = <&smmu_etr 0>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + arm,scatter-gather; + in-ports { + port { + etr_in_port: endpoint { + remote-endpoint = <&replicator_out_port1>; + }; + }; + }; + }; + + stm@20100000 { + compatible = "arm,coresight-stm", "arm,primecell"; + reg = <0 0x20100000 0 0x1000>, + <0 0x28000000 0 0x1000000>; + reg-names = "stm-base", "stm-stimulus-base"; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + out-ports { + port { + stm_out_port: endpoint { + }; + }; + }; + }; + + replicator@20120000 { + compatible = "arm,coresight-dynamic-replicator", "arm,primecell"; + reg = <0 0x20120000 0 0x1000>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + + out-ports { + #address-cells = <1>; + #size-cells = <0>; + + /* replicator output ports */ + port@0 { + reg = <0>; + replicator_out_port0: endpoint { + remote-endpoint = <&tpiu_in_port>; + }; + }; + + port@1 { + reg = <1>; + replicator_out_port1: endpoint { + remote-endpoint = <&etr_in_port>; + }; + }; + }; + in-ports { + port { + replicator_in_port0: endpoint { + }; + }; + }; + }; + + cpu_debug0: cpu-debug@22010000 { + compatible = "arm,coresight-cpu-debug", "arm,primecell"; + reg = <0x0 0x22010000 0x0 0x1000>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + }; + + etm0: etm@22040000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x22040000 0 0x1000>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + out-ports { + port { + cluster0_etm0_out_port: endpoint { + remote-endpoint = <&cluster0_funnel_in_port0>; + }; + }; + }; + }; + + funnel@220c0000 { /* cluster0 funnel */ + compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; + reg = <0 0x220c0000 0 0x1000>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + out-ports { + port { + cluster0_funnel_out_port: endpoint { + remote-endpoint = <&main_funnel_in_port0>; + }; + }; + }; + + in-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + cluster0_funnel_in_port0: endpoint { + remote-endpoint = <&cluster0_etm0_out_port>; + }; + }; + + port@1 { + reg = <1>; + cluster0_funnel_in_port1: endpoint { + remote-endpoint = <&cluster0_etm1_out_port>; + }; + }; + }; + }; + + cpu_debug1: cpu-debug@22110000 { + compatible = "arm,coresight-cpu-debug", "arm,primecell"; + reg = <0x0 0x22110000 0x0 0x1000>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + }; + + etm1: etm@22140000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x22140000 0 0x1000>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + out-ports { + port { + cluster0_etm1_out_port: endpoint { + remote-endpoint = <&cluster0_funnel_in_port1>; + }; + }; + }; + }; + + cpu_debug2: cpu-debug@23010000 { + compatible = "arm,coresight-cpu-debug", "arm,primecell"; + reg = <0x0 0x23010000 0x0 0x1000>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + }; + + etm2: etm@23040000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x23040000 0 0x1000>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + out-ports { + port { + cluster1_etm0_out_port: endpoint { + remote-endpoint = <&cluster1_funnel_in_port0>; + }; + }; + }; + }; + + funnel@230c0000 { /* cluster1 funnel */ + compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; + reg = <0 0x230c0000 0 0x1000>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + out-ports { + port { + cluster1_funnel_out_port: endpoint { + remote-endpoint = <&main_funnel_in_port1>; + }; + }; + }; + + in-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + cluster1_funnel_in_port0: endpoint { + remote-endpoint = <&cluster1_etm0_out_port>; + }; + }; + + port@1 { + reg = <1>; + cluster1_funnel_in_port1: endpoint { + remote-endpoint = <&cluster1_etm1_out_port>; + }; + }; + port@2 { + reg = <2>; + cluster1_funnel_in_port2: endpoint { + remote-endpoint = <&cluster1_etm2_out_port>; + }; + }; + port@3 { + reg = <3>; + cluster1_funnel_in_port3: endpoint { + remote-endpoint = <&cluster1_etm3_out_port>; + }; + }; + }; + }; + + cpu_debug3: cpu-debug@23110000 { + compatible = "arm,coresight-cpu-debug", "arm,primecell"; + reg = <0x0 0x23110000 0x0 0x1000>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + }; + + etm3: etm@23140000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x23140000 0 0x1000>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + out-ports { + port { + cluster1_etm1_out_port: endpoint { + remote-endpoint = <&cluster1_funnel_in_port1>; + }; + }; + }; + }; + + cpu_debug4: cpu-debug@23210000 { + compatible = "arm,coresight-cpu-debug", "arm,primecell"; + reg = <0x0 0x23210000 0x0 0x1000>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + }; + + etm4: etm@23240000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x23240000 0 0x1000>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + out-ports { + port { + cluster1_etm2_out_port: endpoint { + remote-endpoint = <&cluster1_funnel_in_port2>; + }; + }; + }; + }; + + cpu_debug5: cpu-debug@23310000 { + compatible = "arm,coresight-cpu-debug", "arm,primecell"; + reg = <0x0 0x23310000 0x0 0x1000>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + }; + + etm5: etm@23340000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x23340000 0 0x1000>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + out-ports { + port { + cluster1_etm3_out_port: endpoint { + remote-endpoint = <&cluster1_funnel_in_port3>; + }; + }; + }; + }; + + gpu: gpu@2d000000 { + compatible = "arm,juno-mali", "arm,mali-t624"; + reg = <0 0x2d000000 0 0x10000>; + interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "job", "mmu", "gpu"; + clocks = <&scpi_dvfs 2>; + power-domains = <&scpi_devpd 1>; + dma-coherent; + /* The SMMU is only really of interest to bare-metal hypervisors */ + /* iommus = <&smmu_gpu 0>; */ + status = "disabled"; + }; + + sram: sram@2e000000 { + compatible = "arm,juno-sram-ns", "mmio-sram"; + reg = <0x0 0x2e000000 0x0 0x8000>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x0 0x2e000000 0x8000>; + + cpu_scp_lpri: scp-sram@0 { + compatible = "arm,juno-scp-shmem"; + reg = <0x0 0x200>; + }; + + cpu_scp_hpri: scp-sram@200 { + compatible = "arm,juno-scp-shmem"; + reg = <0x200 0x200>; + }; + }; + + pcie_ctlr: pcie@40000000 { + compatible = "arm,juno-r1-pcie", "plda,xpressrich3-axi", "pci-host-ecam-generic"; + device_type = "pci"; + reg = <0 0x40000000 0 0x10000000>; /* ECAM config space */ + bus-range = <0 255>; + linux,pci-domain = <0>; + #address-cells = <3>; + #size-cells = <2>; + dma-coherent; + ranges = <0x01000000 0x00 0x00000000 0x00 0x5f800000 0x0 0x00800000>, + <0x02000000 0x00 0x50000000 0x00 0x50000000 0x0 0x08000000>, + <0x42000000 0x40 0x00000000 0x40 0x00000000 0x1 0x00000000>; + /* Standard AXI Translation entries as programmed by EDK2 */ + dma-ranges = <0x02000000 0x0 0x2c1c0000 0x0 0x2c1c0000 0x0 0x00040000>, + <0x02000000 0x0 0x80000000 0x0 0x80000000 0x0 0x80000000>, + <0x43000000 0x8 0x00000000 0x8 0x00000000 0x2 0x00000000>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &gic 0 GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 2 &gic 0 GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 3 &gic 0 GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 4 &gic 0 GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>; + msi-parent = <&v2m_0>; + status = "disabled"; + iommu-map-mask = <0x0>; /* RC has no means to output PCI RID */ + iommu-map = <0x0 &smmu_pcie 0x0 0x1>; + }; + + scpi { + compatible = "arm,scpi"; + mboxes = <&mailbox 1>; + shmem = <&cpu_scp_hpri>; + + clocks { + compatible = "arm,scpi-clocks"; + + scpi_dvfs: clocks-0 { + compatible = "arm,scpi-dvfs-clocks"; + #clock-cells = <1>; + clock-indices = <0>, <1>, <2>; + clock-output-names = "atlclk", "aplclk","gpuclk"; + }; + scpi_clk: clocks-1 { + compatible = "arm,scpi-variable-clocks"; + #clock-cells = <1>; + clock-indices = <3>; + clock-output-names = "pxlclk"; + }; + }; + + scpi_devpd: power-controller { + compatible = "arm,scpi-power-domains"; + num-domains = <2>; + #power-domain-cells = <1>; + }; + + scpi_sensors0: sensors { + compatible = "arm,scpi-sensors"; + #thermal-sensor-cells = <1>; + }; + }; + + thermal-zones { + pmic { + polling-delay = <1000>; + polling-delay-passive = <100>; + thermal-sensors = <&scpi_sensors0 0>; + }; + + soc { + polling-delay = <1000>; + polling-delay-passive = <100>; + thermal-sensors = <&scpi_sensors0 3>; + }; + + big_cluster_thermal_zone: big-cluster { + polling-delay = <1000>; + polling-delay-passive = <100>; + thermal-sensors = <&scpi_sensors0 21>; + status = "disabled"; + }; + + little_cluster_thermal_zone: little-cluster { + polling-delay = <1000>; + polling-delay-passive = <100>; + thermal-sensors = <&scpi_sensors0 22>; + status = "disabled"; + }; + + gpu0_thermal_zone: gpu0 { + polling-delay = <1000>; + polling-delay-passive = <100>; + thermal-sensors = <&scpi_sensors0 23>; + status = "disabled"; + }; + + gpu1_thermal_zone: gpu1 { + polling-delay = <1000>; + polling-delay-passive = <100>; + thermal-sensors = <&scpi_sensors0 24>; + status = "disabled"; + }; + }; + + smmu_dma: iommu@7fb00000 { + compatible = "arm,mmu-401", "arm,smmu-v1"; + reg = <0x0 0x7fb00000 0x0 0x10000>; + interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + #global-interrupts = <1>; + dma-coherent; + }; + + smmu_hdlcd1: iommu@7fb10000 { + compatible = "arm,mmu-401", "arm,smmu-v1"; + reg = <0x0 0x7fb10000 0x0 0x10000>; + interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + #global-interrupts = <1>; + }; + + smmu_hdlcd0: iommu@7fb20000 { + compatible = "arm,mmu-401", "arm,smmu-v1"; + reg = <0x0 0x7fb20000 0x0 0x10000>; + interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + #global-interrupts = <1>; + }; + + smmu_usb: iommu@7fb30000 { + compatible = "arm,mmu-401", "arm,smmu-v1"; + reg = <0x0 0x7fb30000 0x0 0x10000>; + interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + #global-interrupts = <1>; + dma-coherent; + }; + + dma@7ff00000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0x0 0x7ff00000 0 0x1000>; + #dma-cells = <1>; + #dma-channels = <8>; + #dma-requests = <32>; + interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; + iommus = <&smmu_dma 0>, + <&smmu_dma 1>, + <&smmu_dma 2>, + <&smmu_dma 3>, + <&smmu_dma 4>, + <&smmu_dma 5>, + <&smmu_dma 6>, + <&smmu_dma 7>, + <&smmu_dma 8>; + clocks = <&soc_faxiclk>; + clock-names = "apb_pclk"; + }; + + hdlcd@7ff50000 { + compatible = "arm,hdlcd"; + reg = <0 0x7ff50000 0 0x1000>; + interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; + iommus = <&smmu_hdlcd1 0>; + clocks = <&scpi_clk 3>; + clock-names = "pxlclk"; + + port { + hdlcd1_output: endpoint { + remote-endpoint = <&tda998x_1_input>; + }; + }; + }; + + hdlcd@7ff60000 { + compatible = "arm,hdlcd"; + reg = <0 0x7ff60000 0 0x1000>; + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; + iommus = <&smmu_hdlcd0 0>; + clocks = <&scpi_clk 3>; + clock-names = "pxlclk"; + + port { + hdlcd0_output: endpoint { + remote-endpoint = <&tda998x_0_input>; + }; + }; + }; + + soc_uart0: serial@7ff80000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x0 0x7ff80000 0x0 0x1000>; + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&soc_uartclk>, <&soc_refclk100mhz>; + clock-names = "uartclk", "apb_pclk"; + }; + + i2c@7ffa0000 { + compatible = "snps,designware-i2c"; + reg = <0x0 0x7ffa0000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <400000>; + i2c-sda-hold-time-ns = <500>; + clocks = <&soc_smc50mhz>; + + hdmi-transmitter@70 { + compatible = "nxp,tda998x"; + reg = <0x70>; + port { + tda998x_0_input: endpoint { + remote-endpoint = <&hdlcd0_output>; + }; + }; + }; + + hdmi-transmitter@71 { + compatible = "nxp,tda998x"; + reg = <0x71>; + port { + tda998x_1_input: endpoint { + remote-endpoint = <&hdlcd1_output>; + }; + }; + }; + }; + + usb@7ffb0000 { + compatible = "generic-ohci"; + reg = <0x0 0x7ffb0000 0x0 0x10000>; + interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>; + iommus = <&smmu_usb 0>; + clocks = <&soc_usb48mhz>; + }; + + usb@7ffc0000 { + compatible = "generic-ehci"; + reg = <0x0 0x7ffc0000 0x0 0x10000>; + interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; + iommus = <&smmu_usb 0>; + clocks = <&soc_usb48mhz>; + }; + + memory-controller@7ffd0000 { + compatible = "arm,pl354", "arm,primecell"; + reg = <0 0x7ffd0000 0 0x1000>; + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + }; + + memory@80000000 { + device_type = "memory"; + /* last 16MB of the first memory area is reserved for secure world use by firmware */ + reg = <0x00000000 0x80000000 0x0 0x7f000000>, + <0x00000008 0x80000000 0x1 0x80000000>; + }; + + bus@8000000 { + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 15>; + interrupt-map = <0 0 0 &gic 0 GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>, + <0 0 1 &gic 0 GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>, + <0 0 2 &gic 0 GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>, + <0 0 3 &gic 0 GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>, + <0 0 4 &gic 0 GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>, + <0 0 5 &gic 0 GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>, + <0 0 6 &gic 0 GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>, + <0 0 7 &gic 0 GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>, + <0 0 8 &gic 0 GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>, + <0 0 9 &gic 0 GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>, + <0 0 10 &gic 0 GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>, + <0 0 11 &gic 0 GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>, + <0 0 12 &gic 0 GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>; + }; + + site2: tlx-bus@60000000 { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0x60000000 0x10000000>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0>; + interrupt-map = <0 0 &gic 0 GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>; + }; +}; diff --git a/arch/arm/dts/juno-clocks.dtsi b/arch/arm/dts/juno-clocks.dtsi new file mode 100644 index 0000000..b0f8cca --- /dev/null +++ b/arch/arm/dts/juno-clocks.dtsi @@ -0,0 +1,46 @@ +// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause +/* + * ARM Juno Platform clocks + * + * Copyright (c) 2013-2014 ARM Ltd + * + * This file is licensed under a dual GPLv2 or BSD license. + * + */ +/ { + /* SoC fixed clocks */ + soc_uartclk: refclk7372800hz { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <7372800>; + clock-output-names = "juno:uartclk"; + }; + + soc_usb48mhz: clk48mhz { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <48000000>; + clock-output-names = "clk48mhz"; + }; + + soc_smc50mhz: clk50mhz { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <50000000>; + clock-output-names = "smc_clk"; + }; + + soc_refclk100mhz: refclk100mhz { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <100000000>; + clock-output-names = "apb_pclk"; + }; + + soc_faxiclk: refclk400mhz { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <400000000>; + clock-output-names = "faxi_clk"; + }; +}; diff --git a/arch/arm/dts/juno-cs-r1r2.dtsi b/arch/arm/dts/juno-cs-r1r2.dtsi new file mode 100644 index 0000000..eda3d9e --- /dev/null +++ b/arch/arm/dts/juno-cs-r1r2.dtsi @@ -0,0 +1,85 @@ +// SPDX-License-Identifier: GPL-2.0 +/ { + funnel@20130000 { /* cssys1 */ + compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; + reg = <0 0x20130000 0 0x1000>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + out-ports { + port { + csys1_funnel_out_port: endpoint { + remote-endpoint = <&etf1_in_port>; + }; + }; + }; + in-ports { + port { + csys1_funnel_in_port0: endpoint { + }; + }; + + }; + }; + + etf@20140000 { /* etf1 */ + compatible = "arm,coresight-tmc", "arm,primecell"; + reg = <0 0x20140000 0 0x1000>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + in-ports { + port { + etf1_in_port: endpoint { + remote-endpoint = <&csys1_funnel_out_port>; + }; + }; + }; + out-ports { + port { + etf1_out_port: endpoint { + remote-endpoint = <&csys2_funnel_in_port1>; + }; + }; + }; + }; + + funnel@20150000 { /* cssys2 */ + compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; + reg = <0 0x20150000 0 0x1000>; + + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + power-domains = <&scpi_devpd 0>; + out-ports { + port { + csys2_funnel_out_port: endpoint { + remote-endpoint = <&replicator_in_port0>; + }; + }; + }; + + in-ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + csys2_funnel_in_port0: endpoint { + slave-mode; + remote-endpoint = <&etf0_out_port>; + }; + }; + + port@1 { + reg = <1>; + csys2_funnel_in_port1: endpoint { + slave-mode; + remote-endpoint = <&etf1_out_port>; + }; + }; + + }; + }; +}; diff --git a/arch/arm/dts/juno-motherboard.dtsi b/arch/arm/dts/juno-motherboard.dtsi new file mode 100644 index 0000000..42b1754 --- /dev/null +++ b/arch/arm/dts/juno-motherboard.dtsi @@ -0,0 +1,303 @@ +// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause +/* + * ARM Juno Platform motherboard peripherals + * + * Copyright (c) 2013-2014 ARM Ltd + * + * This file is licensed under a dual GPLv2 or BSD license. + * + */ + +/ { + mb_clk24mhz: clk24mhz { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <24000000>; + clock-output-names = "juno_mb:clk24mhz"; + }; + + mb_clk25mhz: clk25mhz { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <25000000>; + clock-output-names = "juno_mb:clk25mhz"; + }; + + v2m_refclk1mhz: refclk1mhz { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <1000000>; + clock-output-names = "juno_mb:refclk1mhz"; + }; + + v2m_refclk32khz: refclk32khz { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + clock-output-names = "juno_mb:refclk32khz"; + }; + + mb_fixed_3v3: mcc-sb-3v3 { + compatible = "regulator-fixed"; + regulator-name = "MCC_SB_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + gpio-keys { + compatible = "gpio-keys"; + + power-button { + debounce-interval = <50>; + wakeup-source; + linux,code = <116>; + label = "POWER"; + gpios = <&iofpga_gpio0 0 0x4>; + }; + home-button { + debounce-interval = <50>; + wakeup-source; + linux,code = <102>; + label = "HOME"; + gpios = <&iofpga_gpio0 1 0x4>; + }; + rlock-button { + debounce-interval = <50>; + wakeup-source; + linux,code = <152>; + label = "RLOCK"; + gpios = <&iofpga_gpio0 2 0x4>; + }; + vol-up-button { + debounce-interval = <50>; + wakeup-source; + linux,code = <115>; + label = "VOL+"; + gpios = <&iofpga_gpio0 3 0x4>; + }; + vol-down-button { + debounce-interval = <50>; + wakeup-source; + linux,code = <114>; + label = "VOL-"; + gpios = <&iofpga_gpio0 4 0x4>; + }; + nmi-button { + debounce-interval = <50>; + wakeup-source; + linux,code = <99>; + label = "NMI"; + gpios = <&iofpga_gpio0 5 0x4>; + }; + }; + + bus@8000000 { + compatible = "simple-bus"; + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0x8000000 0 0x8000000 0x18000000>; + + motherboard-bus@8000000 { + compatible = "arm,vexpress,v2p-p1", "simple-bus"; + #address-cells = <2>; /* SMB chipselect number and offset */ + #size-cells = <1>; + ranges = <0 0 0 0x08000000 0x04000000>, + <1 0 0 0x14000000 0x04000000>, + <2 0 0 0x18000000 0x04000000>, + <3 0 0 0x1c000000 0x04000000>, + <4 0 0 0x0c000000 0x04000000>, + <5 0 0 0x10000000 0x04000000>; + arm,hbi = <0x252>; + arm,vexpress,site = <0>; + + flash@0 { + /* 2 * 32MiB NOR Flash memory mounted on CS0 */ + compatible = "arm,vexpress-flash", "cfi-flash"; + reg = <0 0x00000000 0x04000000>; + bank-width = <4>; + /* + * Unfortunately, accessing the flash disturbs + * the CPU idle states (suspend) and CPU + * hotplug of the platform. For this reason, + * flash hardware access is disabled by default. + */ + status = "disabled"; + partitions { + compatible = "arm,arm-firmware-suite"; + }; + }; + + ethernet@200000000 { + compatible = "smsc,lan9118", "smsc,lan9115"; + reg = <2 0x00000000 0x10000>; + interrupts = <3>; + phy-mode = "mii"; + reg-io-width = <4>; + smsc,irq-active-high; + smsc,irq-push-pull; + clocks = <&mb_clk25mhz>; + vdd33a-supply = <&mb_fixed_3v3>; + vddvario-supply = <&mb_fixed_3v3>; + }; + + iofpga-bus@300000000 { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 3 0 0x200000>; + + v2m_sysctl: sysctl@20000 { + compatible = "arm,sp810", "arm,primecell"; + reg = <0x020000 0x1000>; + clocks = <&v2m_refclk32khz>, <&v2m_refclk1mhz>, <&mb_clk24mhz>; + clock-names = "refclk", "timclk", "apb_pclk"; + #clock-cells = <1>; + clock-output-names = "timerclken0", "timerclken1", "timerclken2", "timerclken3"; + assigned-clocks = <&v2m_sysctl 0>, <&v2m_sysctl 1>, <&v2m_sysctl 3>, <&v2m_sysctl 3>; + assigned-clock-parents = <&v2m_refclk1mhz>, <&v2m_refclk1mhz>, <&v2m_refclk1mhz>, <&v2m_refclk1mhz>; + }; + + apbregs@10000 { + compatible = "syscon", "simple-mfd"; + reg = <0x010000 0x1000>; + + led0 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x01>; + label = "vexpress:0"; + linux,default-trigger = "heartbeat"; + default-state = "on"; + }; + led1 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x02>; + label = "vexpress:1"; + linux,default-trigger = "mmc0"; + default-state = "off"; + }; + led2 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x04>; + label = "vexpress:2"; + linux,default-trigger = "cpu0"; + default-state = "off"; + }; + led3 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x08>; + label = "vexpress:3"; + linux,default-trigger = "cpu1"; + default-state = "off"; + }; + led4 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x10>; + label = "vexpress:4"; + linux,default-trigger = "cpu2"; + default-state = "off"; + }; + led5 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x20>; + label = "vexpress:5"; + linux,default-trigger = "cpu3"; + default-state = "off"; + }; + led6 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x40>; + label = "vexpress:6"; + default-state = "off"; + }; + led7 { + compatible = "register-bit-led"; + offset = <0x08>; + mask = <0x80>; + label = "vexpress:7"; + default-state = "off"; + }; + }; + + mmc@50000 { + compatible = "arm,pl180", "arm,primecell"; + reg = <0x050000 0x1000>; + interrupts = <5>; + /* cd-gpios = <&v2m_mmc_gpios 0 0>; + wp-gpios = <&v2m_mmc_gpios 1 0>; */ + max-frequency = <12000000>; + vmmc-supply = <&mb_fixed_3v3>; + clocks = <&mb_clk24mhz>, <&soc_smc50mhz>; + clock-names = "mclk", "apb_pclk"; + }; + + kmi@60000 { + compatible = "arm,pl050", "arm,primecell"; + reg = <0x060000 0x1000>; + interrupts = <8>; + clocks = <&mb_clk24mhz>, <&soc_smc50mhz>; + clock-names = "KMIREFCLK", "apb_pclk"; + }; + + kmi@70000 { + compatible = "arm,pl050", "arm,primecell"; + reg = <0x070000 0x1000>; + interrupts = <8>; + clocks = <&mb_clk24mhz>, <&soc_smc50mhz>; + clock-names = "KMIREFCLK", "apb_pclk"; + }; + + watchdog@f0000 { + compatible = "arm,sp805", "arm,primecell"; + reg = <0x0f0000 0x10000>; + interrupts = <7>; + clocks = <&mb_clk24mhz>, <&soc_smc50mhz>; + clock-names = "wdog_clk", "apb_pclk"; + }; + + v2m_timer01: timer@110000 { + compatible = "arm,sp804", "arm,primecell"; + reg = <0x110000 0x10000>; + interrupts = <9>; + clocks = <&v2m_sysctl 0>, <&v2m_sysctl 1>, <&mb_clk24mhz>; + clock-names = "timclken1", "timclken2", "apb_pclk"; + }; + + v2m_timer23: timer@120000 { + compatible = "arm,sp804", "arm,primecell"; + reg = <0x120000 0x10000>; + interrupts = <9>; + clocks = <&v2m_sysctl 2>, <&v2m_sysctl 3>, <&mb_clk24mhz>; + clock-names = "timclken1", "timclken2", "apb_pclk"; + }; + + rtc@170000 { + compatible = "arm,pl031", "arm,primecell"; + reg = <0x170000 0x10000>; + interrupts = <0>; + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + }; + + iofpga_gpio0: gpio@1d0000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0x1d0000 0x1000>; + interrupts = <6>; + clocks = <&soc_smc50mhz>; + clock-names = "apb_pclk"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + }; + }; +}; diff --git a/arch/arm/dts/juno-r2-u-boot.dtsi b/arch/arm/dts/juno-r2-u-boot.dtsi new file mode 100644 index 0000000..7279066 --- /dev/null +++ b/arch/arm/dts/juno-r2-u-boot.dtsi @@ -0,0 +1,20 @@ +// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause +/* + * ARM Juno Platform additions for U-Boot + */ + +/ { + bus@8000000 { + motherboard-bus@8000000 { + /* + * This should not be marked "disabled" in U-Boot. The + * boot loader is not using some CPU idle states and + * hotplug but may be very interested in accessing the + * flash. + */ + flash@0 { + status = "okay"; + }; + }; + }; +}; diff --git a/arch/arm/dts/juno-r2.dts b/arch/arm/dts/juno-r2.dts new file mode 100644 index 0000000..52a6517 --- /dev/null +++ b/arch/arm/dts/juno-r2.dts @@ -0,0 +1,322 @@ +// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause +/* + * ARM Ltd. Juno Platform + * + * Copyright (c) 2015 ARM Ltd. + * + * This file is licensed under a dual GPLv2 or BSD license. + */ + +/dts-v1/; + +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include "juno-base.dtsi" +#include "juno-cs-r1r2.dtsi" + +/ { + model = "ARM Juno development board (r2)"; + compatible = "arm,juno-r2", "arm,juno", "arm,vexpress"; + interrupt-parent = <&gic>; + #address-cells = <2>; + #size-cells = <2>; + + aliases { + serial0 = &soc_uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + psci { + compatible = "arm,psci-0.2"; + method = "smc"; + }; + + cpus { + #address-cells = <2>; + #size-cells = <0>; + + cpu-map { + cluster0 { + core0 { + cpu = <&A72_0>; + }; + core1 { + cpu = <&A72_1>; + }; + }; + + cluster1 { + core0 { + cpu = <&A53_0>; + }; + core1 { + cpu = <&A53_1>; + }; + core2 { + cpu = <&A53_2>; + }; + core3 { + cpu = <&A53_3>; + }; + }; + }; + + idle-states { + entry-method = "psci"; + + CPU_SLEEP_0: cpu-sleep-0 { + compatible = "arm,idle-state"; + arm,psci-suspend-param = <0x0010000>; + local-timer-stop; + entry-latency-us = <300>; + exit-latency-us = <1200>; + min-residency-us = <2000>; + }; + + CLUSTER_SLEEP_0: cluster-sleep-0 { + compatible = "arm,idle-state"; + arm,psci-suspend-param = <0x1010000>; + local-timer-stop; + entry-latency-us = <400>; + exit-latency-us = <1200>; + min-residency-us = <2500>; + }; + }; + + A72_0: cpu@0 { + compatible = "arm,cortex-a72"; + reg = <0x0 0x0>; + device_type = "cpu"; + enable-method = "psci"; + i-cache-size = <0xc000>; + i-cache-line-size = <64>; + i-cache-sets = <256>; + d-cache-size = <0x8000>; + d-cache-line-size = <64>; + d-cache-sets = <256>; + next-level-cache = <&A72_L2>; + clocks = <&scpi_dvfs 0>; + cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; + capacity-dmips-mhz = <1024>; + dynamic-power-coefficient = <450>; + }; + + A72_1: cpu@1 { + compatible = "arm,cortex-a72"; + reg = <0x0 0x1>; + device_type = "cpu"; + enable-method = "psci"; + i-cache-size = <0xc000>; + i-cache-line-size = <64>; + i-cache-sets = <256>; + d-cache-size = <0x8000>; + d-cache-line-size = <64>; + d-cache-sets = <256>; + next-level-cache = <&A72_L2>; + clocks = <&scpi_dvfs 0>; + cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; + capacity-dmips-mhz = <1024>; + dynamic-power-coefficient = <450>; + }; + + A53_0: cpu@100 { + compatible = "arm,cortex-a53"; + reg = <0x0 0x100>; + device_type = "cpu"; + enable-method = "psci"; + i-cache-size = <0x8000>; + i-cache-line-size = <64>; + i-cache-sets = <256>; + d-cache-size = <0x8000>; + d-cache-line-size = <64>; + d-cache-sets = <128>; + next-level-cache = <&A53_L2>; + clocks = <&scpi_dvfs 1>; + cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; + capacity-dmips-mhz = <485>; + dynamic-power-coefficient = <140>; + }; + + A53_1: cpu@101 { + compatible = "arm,cortex-a53"; + reg = <0x0 0x101>; + device_type = "cpu"; + enable-method = "psci"; + i-cache-size = <0x8000>; + i-cache-line-size = <64>; + i-cache-sets = <256>; + d-cache-size = <0x8000>; + d-cache-line-size = <64>; + d-cache-sets = <128>; + next-level-cache = <&A53_L2>; + clocks = <&scpi_dvfs 1>; + cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; + capacity-dmips-mhz = <485>; + dynamic-power-coefficient = <140>; + }; + + A53_2: cpu@102 { + compatible = "arm,cortex-a53"; + reg = <0x0 0x102>; + device_type = "cpu"; + enable-method = "psci"; + i-cache-size = <0x8000>; + i-cache-line-size = <64>; + i-cache-sets = <256>; + d-cache-size = <0x8000>; + d-cache-line-size = <64>; + d-cache-sets = <128>; + next-level-cache = <&A53_L2>; + clocks = <&scpi_dvfs 1>; + cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; + capacity-dmips-mhz = <485>; + dynamic-power-coefficient = <140>; + }; + + A53_3: cpu@103 { + compatible = "arm,cortex-a53"; + reg = <0x0 0x103>; + device_type = "cpu"; + enable-method = "psci"; + i-cache-size = <0x8000>; + i-cache-line-size = <64>; + i-cache-sets = <256>; + d-cache-size = <0x8000>; + d-cache-line-size = <64>; + d-cache-sets = <128>; + next-level-cache = <&A53_L2>; + clocks = <&scpi_dvfs 1>; + cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; + capacity-dmips-mhz = <485>; + dynamic-power-coefficient = <140>; + }; + + A72_L2: l2-cache0 { + compatible = "cache"; + cache-size = <0x200000>; + cache-line-size = <64>; + cache-sets = <2048>; + }; + + A53_L2: l2-cache1 { + compatible = "cache"; + cache-size = <0x100000>; + cache-line-size = <64>; + cache-sets = <1024>; + }; + }; + + pmu-a72 { + compatible = "arm,cortex-a72-pmu"; + interrupts = <GIC_SPI 02 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 06 IRQ_TYPE_LEVEL_HIGH>; + interrupt-affinity = <&A72_0>, + <&A72_1>; + }; + + pmu-a53 { + compatible = "arm,cortex-a53-pmu"; + interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; + interrupt-affinity = <&A53_0>, + <&A53_1>, + <&A53_2>, + <&A53_3>; + }; +}; + +&memtimer { + status = "okay"; +}; + +&pcie_ctlr { + status = "okay"; +}; + +&smmu_pcie { + status = "okay"; +}; + +&etm0 { + cpu = <&A72_0>; +}; + +&etm1 { + cpu = <&A72_1>; +}; + +&etm2 { + cpu = <&A53_0>; +}; + +&etm3 { + cpu = <&A53_1>; +}; + +&etm4 { + cpu = <&A53_2>; +}; + +&etm5 { + cpu = <&A53_3>; +}; + +&big_cluster_thermal_zone { + status = "okay"; +}; + +&little_cluster_thermal_zone { + status = "okay"; +}; + +&gpu0_thermal_zone { + status = "okay"; +}; + +&gpu1_thermal_zone { + status = "okay"; +}; + +&etf0_out_port { + remote-endpoint = <&csys2_funnel_in_port0>; +}; + +&replicator_in_port0 { + remote-endpoint = <&csys2_funnel_out_port>; +}; + +&csys1_funnel_in_port0 { + remote-endpoint = <&stm_out_port>; +}; + +&stm_out_port { + remote-endpoint = <&csys1_funnel_in_port0>; +}; + +&cpu_debug0 { + cpu = <&A72_0>; +}; + +&cpu_debug1 { + cpu = <&A72_1>; +}; + +&cpu_debug2 { + cpu = <&A53_0>; +}; + +&cpu_debug3 { + cpu = <&A53_1>; +}; + +&cpu_debug4 { + cpu = <&A53_2>; +}; + +&cpu_debug5 { + cpu = <&A53_3>; +}; diff --git a/arch/arm/dts/octeontx.dts b/arch/arm/dts/octeontx.dts new file mode 100644 index 0000000..60a15f5 --- /dev/null +++ b/arch/arm/dts/octeontx.dts @@ -0,0 +1,14 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Dummy devicetre file for octeontx2 boards + * + * This is required to make the board build with CONFIG OF_SEPARATE + * I could not find any in-tree documentation at all so this is a dummy file. + * + * Copyright 2021 Google LLC + */ + +/dts-v1/; + +/ { +}; diff --git a/arch/arm/dts/qemu-arm.dts b/arch/arm/dts/qemu-arm.dts new file mode 100644 index 0000000..230c630 --- /dev/null +++ b/arch/arm/dts/qemu-arm.dts @@ -0,0 +1,11 @@ +// SPDX-License-Identifier: GPL-2.0+ OR MIT +/* + * Empty device tree for qemu_arm + + * Copyright 2021 Google LLC + */ + +/dts-v1/; + +/ { +}; diff --git a/arch/arm/dts/qemu-arm64.dts b/arch/arm/dts/qemu-arm64.dts new file mode 100644 index 0000000..096b391 --- /dev/null +++ b/arch/arm/dts/qemu-arm64.dts @@ -0,0 +1,11 @@ +// SPDX-License-Identifier: GPL-2.0+ OR MIT +/* + * Empty device tree for qemu_arm64 + + * Copyright 2021 Google LLC + */ + +/dts-v1/; + +/ { +}; diff --git a/arch/arm/dts/xenguest-arm64.dts b/arch/arm/dts/xenguest-arm64.dts new file mode 100644 index 0000000..d873443 --- /dev/null +++ b/arch/arm/dts/xenguest-arm64.dts @@ -0,0 +1,15 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Empty devicetree file for xenguest_arm64 + * + * This is required to make the board build with CONFIG OF_SEPARATE + * Build instructions at xenguest_arm64.rst are inadequate for obtaining a real + * devicetree. + * + * Copyright 2021 Google LLC + */ + +/dts-v1/; + +/ { +}; diff --git a/arch/arm/dts/xilinx-versal-virt.dts b/arch/arm/dts/xilinx-versal-virt.dts new file mode 100644 index 0000000..733e532 --- /dev/null +++ b/arch/arm/dts/xilinx-versal-virt.dts @@ -0,0 +1,11 @@ +// SPDX-License-Identifier: GPL-2.0+ OR MIT +/* + * Empty device tree for versal-virt board + * + * Copyright 2021 Google LLC + */ + +/dts-v1/; + +/ { +}; diff --git a/arch/arm/mach-bcm283x/Kconfig b/arch/arm/mach-bcm283x/Kconfig index b3287ce..6ce278c 100644 --- a/arch/arm/mach-bcm283x/Kconfig +++ b/arch/arm/mach-bcm283x/Kconfig @@ -163,6 +163,7 @@ config TARGET_RPI_4_32B This option creates a build targeting the ARMv7/AArch32 ISA. select BCM2711_32B + imply OF_HAS_PRIOR_STAGE config TARGET_RPI_4 bool "Raspberry Pi 4 64-bit build" @@ -188,6 +189,7 @@ config TARGET_RPI_4 This option creates a build targeting the ARMv8/AArch64 ISA. select BCM2711_64B + imply OF_HAS_PRIOR_STAGE config TARGET_RPI_ARM64 bool "Raspberry Pi one binary 64-bit build" @@ -195,6 +197,7 @@ config TARGET_RPI_ARM64 Support for all armv8 based Raspberry Pi variants, such as the RPi 4 model B, in AArch64 (64-bit) mode. select ARM64 + imply OF_HAS_PRIOR_STAGE endchoice diff --git a/arch/powerpc/cpu/mpc85xx/Kconfig b/arch/powerpc/cpu/mpc85xx/Kconfig index 836aedd..d71ca86 100644 --- a/arch/powerpc/cpu/mpc85xx/Kconfig +++ b/arch/powerpc/cpu/mpc85xx/Kconfig @@ -109,6 +109,7 @@ config TARGET_QEMU_PPCE500 bool "Support qemu-ppce500" select ARCH_QEMU_E500 select PHYS_64BIT + imply OF_HAS_PRIOR_STAGE config TARGET_T1024RDB bool "Support T1024RDB" diff --git a/arch/powerpc/dts/Makefile b/arch/powerpc/dts/Makefile index ceaa8ce..66d22ae 100644 --- a/arch/powerpc/dts/Makefile +++ b/arch/powerpc/dts/Makefile @@ -18,6 +18,7 @@ dtb-$(CONFIG_TARGET_P2041RDB) += p2041rdb.dtb dtb-$(CONFIG_TARGET_P3041DS) += p3041ds.dtb dtb-$(CONFIG_TARGET_P4080DS) += p4080ds.dtb dtb-$(CONFIG_TARGET_P5040DS) += p5040ds.dtb +dtb-$(CONFIG_TARGET_QEMU_PPCE500) += qemu-ppce500.dtb dtb-$(CONFIG_TARGET_SOCRATES) += socrates.dtb dtb-$(CONFIG_TARGET_T1024RDB) += t1024rdb.dtb dtb-$(CONFIG_TARGET_T1042D4RDB) += t1042d4rdb.dtb diff --git a/arch/powerpc/dts/qemu-ppce500.dts b/arch/powerpc/dts/qemu-ppce500.dts new file mode 100644 index 0000000..e88e09e --- /dev/null +++ b/arch/powerpc/dts/qemu-ppce500.dts @@ -0,0 +1,10 @@ +// SPDX-License-Identifier: GPL-2.0+ OR MIT +/* + * Empty device tree for qemu-ppce400 + * + * Copyright 2021 Google LLC + */ +/dts-v1/; + +/ { +}; diff --git a/arch/riscv/dts/Makefile b/arch/riscv/dts/Makefile index b6e9166..90d3f35 100644 --- a/arch/riscv/dts/Makefile +++ b/arch/riscv/dts/Makefile @@ -2,7 +2,7 @@ dtb-$(CONFIG_TARGET_AX25_AE350) += ae350_32.dtb ae350_64.dtb dtb-$(CONFIG_TARGET_MICROCHIP_ICICLE) += microchip-mpfs-icicle-kit.dtb -dtb-$(CONFIG_TARGET_QEMU_VIRT) += qemu-virt.dtb +dtb-$(CONFIG_TARGET_QEMU_VIRT) += qemu-virt32.dtb qemu-virt64.dtb dtb-$(CONFIG_TARGET_OPENPITON_RISCV64) += openpiton-riscv64.dtb dtb-$(CONFIG_TARGET_SIFIVE_UNLEASHED) += hifive-unleashed-a00.dtb dtb-$(CONFIG_TARGET_SIFIVE_UNMATCHED) += hifive-unmatched-a00.dtb diff --git a/arch/riscv/dts/qemu-virt.dts b/arch/riscv/dts/qemu-virt32.dts index fecff54..17e2f0d 100644 --- a/arch/riscv/dts/qemu-virt.dts +++ b/arch/riscv/dts/qemu-virt32.dts @@ -6,3 +6,6 @@ /dts-v1/; #include "binman.dtsi" + +/ { +}; diff --git a/arch/riscv/dts/qemu-virt64.dts b/arch/riscv/dts/qemu-virt64.dts new file mode 100644 index 0000000..17e2f0d --- /dev/null +++ b/arch/riscv/dts/qemu-virt64.dts @@ -0,0 +1,11 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2021, Bin Meng <bmeng.cn@gmail.com> + */ + +/dts-v1/; + +#include "binman.dtsi" + +/ { +}; diff --git a/board/emulation/qemu-riscv/Kconfig b/board/emulation/qemu-riscv/Kconfig index 1bbf1bc..a380db6 100644 --- a/board/emulation/qemu-riscv/Kconfig +++ b/board/emulation/qemu-riscv/Kconfig @@ -65,5 +65,6 @@ config BOARD_SPECIFIC_OPTIONS # dummy imply VIRTIO_BLK imply MTD_NOR_FLASH imply CFI_FLASH + imply OF_HAS_PRIOR_STAGE endif diff --git a/cmd/bdinfo.c b/cmd/bdinfo.c index bf63cc6..c56b3f4 100644 --- a/cmd/bdinfo.c +++ b/cmd/bdinfo.c @@ -128,6 +128,8 @@ int do_bdinfo(struct cmd_tbl *cmdtp, int flag, int argc, char *const argv[]) lmb_init_and_reserve(&lmb, gd->bd, (void *)gd->fdt_blob); lmb_dump_all_force(&lmb); + if (IS_ENABLED(CONFIG_OF_REAL)) + printf("devicetree = %s\n", fdtdec_get_srcname()); } arch_print_bdinfo(); diff --git a/common/board_r.c b/common/board_r.c index 31a59c5..6d52066 100644 --- a/common/board_r.c +++ b/common/board_r.c @@ -586,6 +586,29 @@ int initr_mem(void) } #endif +static int dm_announce(void) +{ + int device_count; + int uclass_count; + + if (IS_ENABLED(CONFIG_DM)) { + dm_get_stats(&device_count, &uclass_count); + printf("Core: %d devices, %d uclasses", device_count, + uclass_count); + if (CONFIG_IS_ENABLED(OF_REAL)) + printf(", devicetree: %s", fdtdec_get_srcname()); + printf("\n"); + if (IS_ENABLED(CONFIG_OF_HAS_PRIOR_STAGE) && + (gd->fdt_src == FDTSRC_SEPARATE || + gd->fdt_src == FDTSRC_EMBED)) { + printf("Warning: Unexpected devicetree source (not from a prior stage)"); + printf("Warning: U-Boot may not function properly\n"); + } + } + + return 0; +} + static int run_main_loop(void) { #ifdef CONFIG_SANDBOX @@ -661,6 +684,7 @@ static init_fnc_t init_sequence_r[] = { stdio_init_tables, serial_initialize, initr_announce, + dm_announce, #if CONFIG_IS_ENABLED(WDT) initr_watchdog, #endif diff --git a/configs/ae350_rv32_defconfig b/configs/ae350_rv32_defconfig index fe18a1c..f65f58c 100644 --- a/configs/ae350_rv32_defconfig +++ b/configs/ae350_rv32_defconfig @@ -17,7 +17,6 @@ CONFIG_CMD_SF_TEST=y # CONFIG_CMD_SETEXPR is not set CONFIG_BOOTP_PREFER_SERVERIP=y CONFIG_CMD_CACHE=y -CONFIG_OF_BOARD=y CONFIG_ENV_OVERWRITE=y CONFIG_ENV_IS_IN_SPI_FLASH=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y diff --git a/configs/ae350_rv32_spl_defconfig b/configs/ae350_rv32_spl_defconfig index 9287544..9324ed1 100644 --- a/configs/ae350_rv32_spl_defconfig +++ b/configs/ae350_rv32_spl_defconfig @@ -21,7 +21,6 @@ CONFIG_CMD_SF_TEST=y # CONFIG_CMD_SETEXPR is not set CONFIG_BOOTP_PREFER_SERVERIP=y CONFIG_CMD_CACHE=y -CONFIG_OF_BOARD=y CONFIG_ENV_OVERWRITE=y CONFIG_ENV_IS_IN_SPI_FLASH=y CONFIG_BOOTP_SEND_HOSTNAME=y diff --git a/configs/ae350_rv32_spl_xip_defconfig b/configs/ae350_rv32_spl_xip_defconfig index 18d114e..bd06c8e 100644 --- a/configs/ae350_rv32_spl_xip_defconfig +++ b/configs/ae350_rv32_spl_xip_defconfig @@ -23,7 +23,6 @@ CONFIG_CMD_SF_TEST=y # CONFIG_CMD_SETEXPR is not set CONFIG_BOOTP_PREFER_SERVERIP=y CONFIG_CMD_CACHE=y -CONFIG_OF_BOARD=y CONFIG_ENV_OVERWRITE=y CONFIG_ENV_IS_IN_SPI_FLASH=y CONFIG_BOOTP_SEND_HOSTNAME=y diff --git a/configs/ae350_rv64_defconfig b/configs/ae350_rv64_defconfig index 01016c2..479c1de 100644 --- a/configs/ae350_rv64_defconfig +++ b/configs/ae350_rv64_defconfig @@ -18,7 +18,6 @@ CONFIG_CMD_SF_TEST=y # CONFIG_CMD_SETEXPR is not set CONFIG_BOOTP_PREFER_SERVERIP=y CONFIG_CMD_CACHE=y -CONFIG_OF_BOARD=y CONFIG_ENV_OVERWRITE=y CONFIG_ENV_IS_IN_SPI_FLASH=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y diff --git a/configs/ae350_rv64_spl_defconfig b/configs/ae350_rv64_spl_defconfig index 42b93f5..1ec993c 100644 --- a/configs/ae350_rv64_spl_defconfig +++ b/configs/ae350_rv64_spl_defconfig @@ -22,7 +22,6 @@ CONFIG_CMD_SF_TEST=y # CONFIG_CMD_SETEXPR is not set CONFIG_BOOTP_PREFER_SERVERIP=y CONFIG_CMD_CACHE=y -CONFIG_OF_BOARD=y CONFIG_ENV_OVERWRITE=y CONFIG_ENV_IS_IN_SPI_FLASH=y CONFIG_BOOTP_SEND_HOSTNAME=y diff --git a/configs/ae350_rv64_spl_xip_defconfig b/configs/ae350_rv64_spl_xip_defconfig index 9071b7c..b6a97f2 100644 --- a/configs/ae350_rv64_spl_xip_defconfig +++ b/configs/ae350_rv64_spl_xip_defconfig @@ -24,7 +24,6 @@ CONFIG_CMD_SF_TEST=y # CONFIG_CMD_SETEXPR is not set CONFIG_BOOTP_PREFER_SERVERIP=y CONFIG_CMD_CACHE=y -CONFIG_OF_BOARD=y CONFIG_ENV_OVERWRITE=y CONFIG_ENV_IS_IN_SPI_FLASH=y CONFIG_BOOTP_SEND_HOSTNAME=y diff --git a/configs/bcm7260_defconfig b/configs/bcm7260_defconfig index 257d810..d430dea 100644 --- a/configs/bcm7260_defconfig +++ b/configs/bcm7260_defconfig @@ -7,6 +7,7 @@ CONFIG_TARGET_BCM7260=y CONFIG_NR_DRAM_BANKS=1 CONFIG_ENV_SIZE=0x10000 CONFIG_ENV_OFFSET=0x814800 +CONFIG_DEFAULT_DEVICE_TREE="bcm7xxx" CONFIG_ENV_OFFSET_REDUND=0x824800 CONFIG_SYS_LOAD_ADDR=0x02000000 CONFIG_FIT=y @@ -26,7 +27,6 @@ CONFIG_CMD_EXT2=y CONFIG_CMD_EXT4=y CONFIG_CMD_FS_GENERIC=y CONFIG_DOS_PARTITION=y -CONFIG_OF_BOARD=y CONFIG_ENV_OVERWRITE=y CONFIG_ENV_IS_IN_MMC=y CONFIG_SYS_REDUNDAND_ENVIRONMENT=y diff --git a/configs/bcm7445_defconfig b/configs/bcm7445_defconfig index 9ffa436..de64161 100644 --- a/configs/bcm7445_defconfig +++ b/configs/bcm7445_defconfig @@ -8,6 +8,7 @@ CONFIG_NR_DRAM_BANKS=3 CONFIG_ENV_SIZE=0x10000 CONFIG_ENV_OFFSET=0x1E0000 CONFIG_ENV_SECT_SIZE=0x10000 +CONFIG_DEFAULT_DEVICE_TREE="bcm7xxx" CONFIG_ENV_OFFSET_REDUND=0x1F0000 CONFIG_SYS_LOAD_ADDR=0x02000000 CONFIG_FIT=y @@ -27,7 +28,6 @@ CONFIG_CMD_EXT2=y CONFIG_CMD_EXT4=y CONFIG_CMD_FS_GENERIC=y CONFIG_DOS_PARTITION=y -CONFIG_OF_BOARD=y CONFIG_ENV_OVERWRITE=y CONFIG_ENV_IS_IN_SPI_FLASH=y CONFIG_SYS_REDUNDAND_ENVIRONMENT=y diff --git a/configs/highbank_defconfig b/configs/highbank_defconfig index 85b42c7..3e8bfcf 100644 --- a/configs/highbank_defconfig +++ b/configs/highbank_defconfig @@ -7,6 +7,7 @@ CONFIG_SYS_TEXT_BASE=0x00008000 CONFIG_SYS_MALLOC_LEN=0x80000 CONFIG_NR_DRAM_BANKS=2 CONFIG_ENV_SIZE=0x2000 +CONFIG_DEFAULT_DEVICE_TREE="highbank" CONFIG_SYS_BOOTCOUNT_ADDR=0xfff3cf0c CONFIG_SYS_BOOTCOUNT_SINGLEWORD=y CONFIG_DISTRO_DEFAULTS=y @@ -21,7 +22,6 @@ CONFIG_AUTOBOOT_KEYED_CTRLC=y # CONFIG_DISPLAY_BOARDINFO is not set CONFIG_MISC_INIT_R=y # CONFIG_CMD_SETEXPR is not set -CONFIG_OF_BOARD=y CONFIG_ENV_IS_IN_NVRAM=y CONFIG_ENV_ADDR=0xFFF88000 CONFIG_SCSI_AHCI=y diff --git a/configs/octeontx2_95xx_defconfig b/configs/octeontx2_95xx_defconfig index e1b86a5..0dbb954 100644 --- a/configs/octeontx2_95xx_defconfig +++ b/configs/octeontx2_95xx_defconfig @@ -12,6 +12,7 @@ CONFIG_ENV_OFFSET=0xF00000 CONFIG_ENV_SECT_SIZE=0x10000 CONFIG_TARGET_OCTEONTX2_95XX=y CONFIG_DM_GPIO=y +CONFIG_DEFAULT_DEVICE_TREE="octeontx" CONFIG_DEBUG_UART_BASE=0x87e028000000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_DEBUG_UART=y @@ -63,7 +64,6 @@ CONFIG_CMD_FAT=y CONFIG_CMD_FS_GENERIC=y CONFIG_EFI_PARTITION=y CONFIG_PARTITION_TYPE_GUID=y -CONFIG_OF_BOARD=y CONFIG_ENV_OVERWRITE=y CONFIG_ENV_IS_IN_SPI_FLASH=y CONFIG_USE_ENV_SPI_BUS=y diff --git a/configs/octeontx2_96xx_defconfig b/configs/octeontx2_96xx_defconfig index ec03d95..65fb847 100644 --- a/configs/octeontx2_96xx_defconfig +++ b/configs/octeontx2_96xx_defconfig @@ -10,6 +10,7 @@ CONFIG_ENV_OFFSET=0xF00000 CONFIG_ENV_SECT_SIZE=0x10000 CONFIG_TARGET_OCTEONTX2_96XX=y CONFIG_DM_GPIO=y +CONFIG_DEFAULT_DEVICE_TREE="octeontx" CONFIG_DEBUG_UART_BASE=0x87e028000000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_DEBUG_UART=y @@ -64,7 +65,6 @@ CONFIG_CMD_FAT=y CONFIG_CMD_FS_GENERIC=y CONFIG_EFI_PARTITION=y CONFIG_PARTITION_TYPE_GUID=y -CONFIG_OF_BOARD=y CONFIG_ENV_OVERWRITE=y CONFIG_ENV_IS_IN_SPI_FLASH=y CONFIG_USE_ENV_SPI_BUS=y diff --git a/configs/octeontx_81xx_defconfig b/configs/octeontx_81xx_defconfig index d0728ac..ea62be3 100644 --- a/configs/octeontx_81xx_defconfig +++ b/configs/octeontx_81xx_defconfig @@ -12,6 +12,7 @@ CONFIG_ENV_OFFSET=0xF00000 CONFIG_ENV_SECT_SIZE=0x10000 CONFIG_TARGET_OCTEONTX_81XX=y CONFIG_DM_GPIO=y +CONFIG_DEFAULT_DEVICE_TREE="octeontx" CONFIG_DEBUG_UART_BASE=0x87e028000000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_DEBUG_UART=y @@ -65,7 +66,6 @@ CONFIG_CMD_FAT=y CONFIG_CMD_FS_GENERIC=y CONFIG_EFI_PARTITION=y CONFIG_PARTITION_TYPE_GUID=y -CONFIG_OF_BOARD=y CONFIG_ENV_OVERWRITE=y CONFIG_ENV_IS_IN_SPI_FLASH=y CONFIG_USE_ENV_SPI_BUS=y diff --git a/configs/octeontx_83xx_defconfig b/configs/octeontx_83xx_defconfig index 6c9609b..47ddc50 100644 --- a/configs/octeontx_83xx_defconfig +++ b/configs/octeontx_83xx_defconfig @@ -10,6 +10,7 @@ CONFIG_ENV_OFFSET=0xF00000 CONFIG_ENV_SECT_SIZE=0x10000 CONFIG_TARGET_OCTEONTX_83XX=y CONFIG_DM_GPIO=y +CONFIG_DEFAULT_DEVICE_TREE="octeontx" CONFIG_DEBUG_UART_BASE=0x87e028000000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_DEBUG_UART=y @@ -62,7 +63,6 @@ CONFIG_CMD_FAT=y CONFIG_CMD_FS_GENERIC=y CONFIG_EFI_PARTITION=y CONFIG_PARTITION_TYPE_GUID=y -CONFIG_OF_BOARD=y CONFIG_ENV_OVERWRITE=y CONFIG_ENV_IS_IN_SPI_FLASH=y CONFIG_USE_ENV_SPI_BUS=y diff --git a/configs/qemu-ppce500_defconfig b/configs/qemu-ppce500_defconfig index f386f52..894203d 100644 --- a/configs/qemu-ppce500_defconfig +++ b/configs/qemu-ppce500_defconfig @@ -1,6 +1,7 @@ CONFIG_PPC=y CONFIG_SYS_TEXT_BASE=0xf01000 CONFIG_ENV_SIZE=0x2000 +CONFIG_DEFAULT_DEVICE_TREE="qemu-ppce500" CONFIG_MPC85xx=y # CONFIG_CMD_ERRATA is not set CONFIG_TARGET_QEMU_PPCE500=y @@ -26,7 +27,6 @@ CONFIG_CMD_PING=y CONFIG_CMD_EXT2=y CONFIG_DOS_PARTITION=y CONFIG_OF_CONTROL=y -CONFIG_OF_BOARD=y CONFIG_ENV_OVERWRITE=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_NET_RANDOM_ETHADDR=y @@ -55,4 +55,5 @@ CONFIG_VIRTIO_PCI=y CONFIG_VIRTIO_NET=y CONFIG_VIRTIO_BLK=y CONFIG_ADDR_MAP=y +# CONFIG_BINMAN_FDT is not set CONFIG_PANIC_HANG=y diff --git a/configs/qemu-riscv32_defconfig b/configs/qemu-riscv32_defconfig index 0b8cd19..b892fd6 100644 --- a/configs/qemu-riscv32_defconfig +++ b/configs/qemu-riscv32_defconfig @@ -2,6 +2,7 @@ CONFIG_RISCV=y CONFIG_SYS_MALLOC_LEN=0x800000 CONFIG_NR_DRAM_BANKS=1 CONFIG_ENV_SIZE=0x20000 +CONFIG_DEFAULT_DEVICE_TREE="qemu-virt32" CONFIG_TARGET_QEMU_VIRT=y CONFIG_DISTRO_DEFAULTS=y CONFIG_SYS_LOAD_ADDR=0x80200000 @@ -11,6 +12,5 @@ CONFIG_DISPLAY_BOARDINFO=y CONFIG_CMD_BOOTEFI_SELFTEST=y CONFIG_CMD_NVEDIT_EFI=y # CONFIG_CMD_MII is not set -CONFIG_OF_BOARD=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_DM_MTD=y diff --git a/configs/qemu-riscv32_smode_defconfig b/configs/qemu-riscv32_smode_defconfig index 4d65104..b4856fd 100644 --- a/configs/qemu-riscv32_smode_defconfig +++ b/configs/qemu-riscv32_smode_defconfig @@ -2,6 +2,7 @@ CONFIG_RISCV=y CONFIG_SYS_MALLOC_LEN=0x800000 CONFIG_NR_DRAM_BANKS=1 CONFIG_ENV_SIZE=0x20000 +CONFIG_DEFAULT_DEVICE_TREE="qemu-virt32" CONFIG_TARGET_QEMU_VIRT=y CONFIG_RISCV_SMODE=y CONFIG_DISTRO_DEFAULTS=y @@ -12,7 +13,6 @@ CONFIG_DISPLAY_BOARDINFO=y CONFIG_CMD_BOOTEFI_SELFTEST=y CONFIG_CMD_NVEDIT_EFI=y # CONFIG_CMD_MII is not set -CONFIG_OF_BOARD=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_DM_MTD=y CONFIG_SYSRESET_SBI=y diff --git a/configs/qemu-riscv32_spl_defconfig b/configs/qemu-riscv32_spl_defconfig index eb64c51..efe8d39 100644 --- a/configs/qemu-riscv32_spl_defconfig +++ b/configs/qemu-riscv32_spl_defconfig @@ -2,10 +2,11 @@ CONFIG_RISCV=y CONFIG_SYS_MALLOC_LEN=0x800000 CONFIG_NR_DRAM_BANKS=1 CONFIG_ENV_SIZE=0x20000 -CONFIG_DEFAULT_DEVICE_TREE="qemu-virt" +CONFIG_DEFAULT_DEVICE_TREE="qemu-virt32" CONFIG_SPL=y CONFIG_TARGET_QEMU_VIRT=y CONFIG_RISCV_SMODE=y +# CONFIG_OF_BOARD_FIXUP is not set CONFIG_DISTRO_DEFAULTS=y CONFIG_SYS_LOAD_ADDR=0x80200000 CONFIG_FIT=y @@ -14,7 +15,7 @@ CONFIG_DISPLAY_CPUINFO=y CONFIG_DISPLAY_BOARDINFO=y CONFIG_CMD_SBI=y # CONFIG_CMD_MII is not set -CONFIG_OF_BOARD=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_DM_MTD=y CONFIG_SYSRESET_SBI=y +# CONFIG_BINMAN_FDT is not set diff --git a/configs/qemu-riscv64_defconfig b/configs/qemu-riscv64_defconfig index 4faa6da..036484c 100644 --- a/configs/qemu-riscv64_defconfig +++ b/configs/qemu-riscv64_defconfig @@ -2,6 +2,7 @@ CONFIG_RISCV=y CONFIG_SYS_MALLOC_LEN=0x800000 CONFIG_NR_DRAM_BANKS=1 CONFIG_ENV_SIZE=0x20000 +CONFIG_DEFAULT_DEVICE_TREE="qemu-virt64" CONFIG_TARGET_QEMU_VIRT=y CONFIG_ARCH_RV64I=y CONFIG_DISTRO_DEFAULTS=y @@ -12,6 +13,5 @@ CONFIG_DISPLAY_BOARDINFO=y CONFIG_CMD_BOOTEFI_SELFTEST=y CONFIG_CMD_NVEDIT_EFI=y # CONFIG_CMD_MII is not set -CONFIG_OF_BOARD=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_DM_MTD=y diff --git a/configs/qemu-riscv64_smode_defconfig b/configs/qemu-riscv64_smode_defconfig index f575c12..e519bb6 100644 --- a/configs/qemu-riscv64_smode_defconfig +++ b/configs/qemu-riscv64_smode_defconfig @@ -2,6 +2,7 @@ CONFIG_RISCV=y CONFIG_SYS_MALLOC_LEN=0x800000 CONFIG_NR_DRAM_BANKS=1 CONFIG_ENV_SIZE=0x20000 +CONFIG_DEFAULT_DEVICE_TREE="qemu-virt64" CONFIG_TARGET_QEMU_VIRT=y CONFIG_ARCH_RV64I=y CONFIG_RISCV_SMODE=y @@ -15,7 +16,6 @@ CONFIG_DISPLAY_BOARDINFO=y CONFIG_CMD_BOOTEFI_SELFTEST=y CONFIG_CMD_NVEDIT_EFI=y # CONFIG_CMD_MII is not set -CONFIG_OF_BOARD=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_DM_MTD=y CONFIG_SYSRESET_SBI=y diff --git a/configs/qemu-riscv64_spl_defconfig b/configs/qemu-riscv64_spl_defconfig index 0fbdb75..8b51237 100644 --- a/configs/qemu-riscv64_spl_defconfig +++ b/configs/qemu-riscv64_spl_defconfig @@ -2,7 +2,7 @@ CONFIG_RISCV=y CONFIG_SYS_MALLOC_LEN=0x800000 CONFIG_NR_DRAM_BANKS=1 CONFIG_ENV_SIZE=0x20000 -CONFIG_DEFAULT_DEVICE_TREE="qemu-virt" +CONFIG_DEFAULT_DEVICE_TREE="qemu-virt64" CONFIG_SPL=y CONFIG_TARGET_QEMU_VIRT=y CONFIG_ARCH_RV64I=y @@ -15,7 +15,7 @@ CONFIG_DISPLAY_CPUINFO=y CONFIG_DISPLAY_BOARDINFO=y CONFIG_CMD_SBI=y # CONFIG_CMD_MII is not set -CONFIG_OF_BOARD=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_DM_MTD=y CONFIG_SYSRESET_SBI=y +# CONFIG_BINMAN_FDT is not set diff --git a/configs/qemu_arm64_defconfig b/configs/qemu_arm64_defconfig index 0ac3b47..5e41ea9 100644 --- a/configs/qemu_arm64_defconfig +++ b/configs/qemu_arm64_defconfig @@ -5,6 +5,7 @@ CONFIG_SYS_MALLOC_LEN=0x1000000 CONFIG_NR_DRAM_BANKS=1 CONFIG_ENV_SIZE=0x40000 CONFIG_ENV_SECT_SIZE=0x40000 +CONFIG_DEFAULT_DEVICE_TREE="qemu-arm64" CONFIG_DEBUG_UART_BASE=0x9000000 CONFIG_DEBUG_UART_CLOCK=0 CONFIG_DEBUG_UART=y @@ -28,7 +29,6 @@ CONFIG_CMD_PCI=y CONFIG_CMD_USB=y CONFIG_CMD_TPM=y CONFIG_CMD_MTDPARTS=y -CONFIG_OF_BOARD=y CONFIG_ENV_IS_IN_FLASH=y CONFIG_ENV_ADDR=0x4000000 CONFIG_SCSI_AHCI=y diff --git a/configs/qemu_arm_defconfig b/configs/qemu_arm_defconfig index 8ce5540..4197cb0 100644 --- a/configs/qemu_arm_defconfig +++ b/configs/qemu_arm_defconfig @@ -5,6 +5,7 @@ CONFIG_SYS_MALLOC_LEN=0x1000000 CONFIG_NR_DRAM_BANKS=1 CONFIG_ENV_SIZE=0x40000 CONFIG_ENV_SECT_SIZE=0x40000 +CONFIG_DEFAULT_DEVICE_TREE="qemu-arm" CONFIG_TARGET_QEMU_ARM_32BIT=y CONFIG_DEBUG_UART_BASE=0x9000000 CONFIG_DEBUG_UART_CLOCK=0 @@ -30,7 +31,6 @@ CONFIG_CMD_PCI=y CONFIG_CMD_USB=y CONFIG_CMD_TPM=y CONFIG_CMD_MTDPARTS=y -CONFIG_OF_BOARD=y CONFIG_ENV_IS_IN_FLASH=y CONFIG_ENV_ADDR=0x4000000 CONFIG_SCSI_AHCI=y diff --git a/configs/rpi_4_32b_defconfig b/configs/rpi_4_32b_defconfig index 88f7504..8f87a43 100644 --- a/configs/rpi_4_32b_defconfig +++ b/configs/rpi_4_32b_defconfig @@ -4,6 +4,7 @@ CONFIG_SYS_TEXT_BASE=0x00008000 CONFIG_SYS_MALLOC_F_LEN=0x2000 CONFIG_TARGET_RPI_4_32B=y CONFIG_ENV_SIZE=0x4000 +CONFIG_DEFAULT_DEVICE_TREE="bcm2711-rpi-4-b" CONFIG_DISTRO_DEFAULTS=y CONFIG_SYS_LOAD_ADDR=0x1000000 CONFIG_OF_BOARD_SETUP=y @@ -20,7 +21,6 @@ CONFIG_CMD_MMC=y CONFIG_CMD_PCI=y CONFIG_CMD_USB=y CONFIG_CMD_FS_UUID=y -CONFIG_OF_BOARD=y CONFIG_ENV_FAT_DEVICE_AND_PART="0:1" CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y diff --git a/configs/rpi_4_defconfig b/configs/rpi_4_defconfig index 59a7103..461a765 100644 --- a/configs/rpi_4_defconfig +++ b/configs/rpi_4_defconfig @@ -4,6 +4,7 @@ CONFIG_SYS_TEXT_BASE=0x00080000 CONFIG_SYS_MALLOC_F_LEN=0x2000 CONFIG_TARGET_RPI_4=y CONFIG_ENV_SIZE=0x4000 +CONFIG_DEFAULT_DEVICE_TREE="bcm2711-rpi-4-b" CONFIG_DISTRO_DEFAULTS=y CONFIG_SYS_LOAD_ADDR=0x1000000 CONFIG_OF_BOARD_SETUP=y @@ -20,7 +21,6 @@ CONFIG_CMD_MMC=y CONFIG_CMD_PCI=y CONFIG_CMD_USB=y CONFIG_CMD_FS_UUID=y -CONFIG_OF_BOARD=y CONFIG_ENV_FAT_DEVICE_AND_PART="0:1" CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y diff --git a/configs/rpi_arm64_defconfig b/configs/rpi_arm64_defconfig index 67dbf09..351d247 100644 --- a/configs/rpi_arm64_defconfig +++ b/configs/rpi_arm64_defconfig @@ -4,6 +4,7 @@ CONFIG_SYS_TEXT_BASE=0x00080000 CONFIG_SYS_MALLOC_F_LEN=0x2000 CONFIG_TARGET_RPI_ARM64=y CONFIG_ENV_SIZE=0x4000 +CONFIG_DEFAULT_DEVICE_TREE="bcm2711-rpi-4-b" CONFIG_DISTRO_DEFAULTS=y CONFIG_SYS_LOAD_ADDR=0x1000000 CONFIG_OF_BOARD_SETUP=y @@ -19,7 +20,6 @@ CONFIG_CMD_MMC=y CONFIG_CMD_PCI=y CONFIG_CMD_USB=y CONFIG_CMD_FS_UUID=y -CONFIG_OF_BOARD=y CONFIG_ENV_FAT_DEVICE_AND_PART="0:1" CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y CONFIG_TFTP_TSIZE=y diff --git a/configs/vexpress_aemv8a_juno_defconfig b/configs/vexpress_aemv8a_juno_defconfig index f6ff0e0..ffadfc0 100644 --- a/configs/vexpress_aemv8a_juno_defconfig +++ b/configs/vexpress_aemv8a_juno_defconfig @@ -8,6 +8,7 @@ CONFIG_SYS_MEMTEST_START=0x80000000 CONFIG_SYS_MEMTEST_END=0xff000000 CONFIG_ENV_SIZE=0x10000 CONFIG_ENV_SECT_SIZE=0x10000 +CONFIG_DEFAULT_DEVICE_TREE="juno-r2" CONFIG_IDENT_STRING=" vexpress_aemv8a" CONFIG_DISTRO_DEFAULTS=y CONFIG_SYS_LOAD_ADDR=0x90000000 @@ -32,7 +33,6 @@ CONFIG_CMD_USB=y CONFIG_CMD_CACHE=y # CONFIG_CMD_SLEEP is not set CONFIG_CMD_UBI=y -CONFIG_OF_BOARD=y CONFIG_ENV_IS_IN_FLASH=y CONFIG_ENV_ADDR=0xBFC0000 CONFIG_SATA_SIL=y diff --git a/configs/xenguest_arm64_defconfig b/configs/xenguest_arm64_defconfig index 8d9d913..223bb78 100644 --- a/configs/xenguest_arm64_defconfig +++ b/configs/xenguest_arm64_defconfig @@ -3,7 +3,7 @@ CONFIG_POSITION_INDEPENDENT=y CONFIG_TARGET_XENGUEST_ARM64=y CONFIG_SYS_TEXT_BASE=0x40080000 CONFIG_SYS_MALLOC_LEN=0x2000000 -CONFIG_SYS_MALLOC_F_LEN=0x2000 +CONFIG_DEFAULT_DEVICE_TREE="xenguest-arm64" CONFIG_IDENT_STRING=" xenguest" CONFIG_SYS_LOAD_ADDR=0x40000000 CONFIG_BOOTDELAY=10 @@ -33,7 +33,6 @@ CONFIG_CMD_PVBLOCK=y # CONFIG_CMD_SLEEP is not set CONFIG_CMD_EXT4=y CONFIG_CMD_FAT=y -CONFIG_OF_BOARD=y CONFIG_DM=y # CONFIG_MMC is not set # CONFIG_REQUIRE_SERIAL_CONSOLE is not set diff --git a/configs/xilinx_versal_virt_defconfig b/configs/xilinx_versal_virt_defconfig index 1159862..f0ec263 100644 --- a/configs/xilinx_versal_virt_defconfig +++ b/configs/xilinx_versal_virt_defconfig @@ -7,6 +7,7 @@ CONFIG_SYS_MALLOC_F_LEN=0x100000 CONFIG_SYS_MEMTEST_START=0x00000000 CONFIG_SYS_MEMTEST_END=0x00001000 CONFIG_DM_GPIO=y +CONFIG_DEFAULT_DEVICE_TREE="xilinx-versal-virt" CONFIG_CMD_FRU=y CONFIG_DEFINE_TCM_OCM_MMAP=y CONFIG_COUNTER_FREQUENCY=100000000 diff --git a/doc/board/emulation/qemu-arm.rst b/doc/board/emulation/qemu-arm.rst index 7c24e29..16f6638 100644 --- a/doc/board/emulation/qemu-arm.rst +++ b/doc/board/emulation/qemu-arm.rst @@ -21,6 +21,9 @@ The 'virt' platform provides the following as the basic functionality: Additionally, a number of optional peripherals can be added to the PCI bus. +See :doc:`../../develop/devicetree/dt_qemu` for information on how to see +the devicetree actually generated by QEMU. + Building U-Boot --------------- Set the CROSS_COMPILE environment variable as usual, and run: @@ -41,14 +44,15 @@ The minimal QEMU command line to get U-Boot up and running is: - For ARM:: - qemu-system-arm -machine virt -bios u-boot.bin + qemu-system-arm -machine virt -nographic -bios u-boot.bin - For AArch64:: - qemu-system-aarch64 -machine virt -cpu cortex-a57 -bios u-boot.bin + qemu-system-aarch64 -machine virt -nographic -cpu cortex-a57 -bios u-boot.bin Note that for some odd reason qemu-system-aarch64 needs to be explicitly -told to use a 64-bit CPU or it will boot in 32-bit mode. +told to use a 64-bit CPU or it will boot in 32-bit mode. The -nographic argument +ensures that output appears on the terminal. Use Ctrl-A X to quit. Additional persistent U-boot environment support can be added as follows: diff --git a/doc/board/emulation/qemu-riscv.rst b/doc/board/emulation/qemu-riscv.rst index 4b8e104..3409fff 100644 --- a/doc/board/emulation/qemu-riscv.rst +++ b/doc/board/emulation/qemu-riscv.rst @@ -13,6 +13,9 @@ The QEMU virt machine models a generic RISC-V virtual machine with support for the VirtIO standard networking and block storage devices. It has CLINT, PLIC, 16550A UART devices in addition to VirtIO and it also uses device-tree to pass configuration information to guest software. It implements RISC-V privileged + +See :doc:`../../develop/devicetree/dt_qemu` for information on how to see +the devicetree actually generated by QEMU. architecture spec v1.10. Building U-Boot diff --git a/doc/develop/devicetree/dt_qemu.rst b/doc/develop/devicetree/dt_qemu.rst new file mode 100644 index 0000000..c25c4fb --- /dev/null +++ b/doc/develop/devicetree/dt_qemu.rst @@ -0,0 +1,48 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +Devicetree in QEMU +================== + +For QEMU on ARM, RISC-V and one PPC target, the devicetree is created on-the-fly +by QEMU. It is intended for use in Linux but can be used by U-Boot also, so long +as any nodes/properties needed by U-Boot are merged in. + +When `CONFIG_OF_BOARD` is enabled + + +Obtaining the QEMU devicetree +----------------------------- + +Where QEMU generates its own devicetree to pass to U-Boot tou can use +`-dtb u-boot.dtb` to force QEMU to use U-Boot's in-tree version. + +To obtain the devicetree that qemu generates, add `-machine dumpdtb=qemu.dtb`, +e.g.:: + + qemu-system-arm -machine virt -machine dumpdtb=qemu.dtb + + qemu-system-aarch64 -machine virt -machine dumpdtb=qemu.dtb + + qemu-system-riscv64 -machine virt -machine dumpdtb=qemu.dtb + + +Merging in U-Boot nodes/properties +---------------------------------- + +Various U-Boot features require nodes and properties in the U-Boot devicetree +and at present QEMU is unaware of these. To use these you must manually merge +in the appropriate pieces. + +One way to do this is with dtc. This command runs dtc on each .dtb file in turn, +to produce a text file. It drops the duplicate header on the qemu one. Then it +joins them up and runs them through dtc to compile the output:: + + qemu-system-arm -machine virt -machine dumpdtb=qemu.dtb + cat <(dtc -I dtb qemu.dtb) <(dtc -I dtb u-boot.dtb |grep -v /dts-v1/) |dtc - -o merged.dtb + +You can then run qemu with the merged devicetree, e.g.:: + + qemu-system-arm -machine virt -nographic -bios u-boot.bin -dtb merged.dtb + +Note that there seems to be a bug in some versions of qemu where the output of +dumpdtb does not quite match what is provided to U-Boot. diff --git a/doc/develop/devicetree/index.rst b/doc/develop/devicetree/index.rst index fa5db3e..2edb695 100644 --- a/doc/develop/devicetree/index.rst +++ b/doc/develop/devicetree/index.rst @@ -11,3 +11,4 @@ build-time and runtime configuration. intro control + dt_qemu diff --git a/drivers/core/device.c b/drivers/core/device.c index 74374ff..4873c47 100644 --- a/drivers/core/device.c +++ b/drivers/core/device.c @@ -739,6 +739,17 @@ int device_get_child_count(const struct udevice *parent) return count; } +int device_get_decendent_count(const struct udevice *parent) +{ + const struct udevice *dev; + int count = 1; + + list_for_each_entry(dev, &parent->child_head, sibling_node) + count += device_get_decendent_count(dev); + + return count; +} + int device_find_child_by_seq(const struct udevice *parent, int seq, struct udevice **devp) { diff --git a/drivers/core/root.c b/drivers/core/root.c index 26b8195..815173f 100644 --- a/drivers/core/root.c +++ b/drivers/core/root.c @@ -26,6 +26,7 @@ #include <dm/read.h> #include <dm/root.h> #include <dm/uclass.h> +#include <dm/uclass-internal.h> #include <dm/util.h> #include <linux/list.h> @@ -407,6 +408,12 @@ int dm_init_and_scan(bool pre_reloc_only) return 0; } +void dm_get_stats(int *device_countp, int *uclass_countp) +{ + *device_countp = device_get_decendent_count(gd->dm_root); + *uclass_countp = uclass_get_count(); +} + #ifdef CONFIG_ACPIGEN static int root_acpi_get_name(const struct udevice *dev, char *out_name) { diff --git a/drivers/core/uclass.c b/drivers/core/uclass.c index 2aa2143..336ea8d 100644 --- a/drivers/core/uclass.c +++ b/drivers/core/uclass.c @@ -643,6 +643,19 @@ int uclass_next_device_check(struct udevice **devp) return device_probe(*devp); } +int uclass_get_count(void) +{ + const struct uclass *uc; + int count = 0; + + if (gd->dm_root) { + list_for_each_entry(uc, gd->uclass_root, sibling_node) + count++; + } + + return count; +} + int uclass_first_device_drvdata(enum uclass_id id, ulong driver_data, struct udevice **devp) { diff --git a/dts/Kconfig b/dts/Kconfig index b7c4a2f..fb7df53 100644 --- a/dts/Kconfig +++ b/dts/Kconfig @@ -16,24 +16,6 @@ config BINMAN bool select DTOC -config BINMAN_STANDALONE_FDT - bool - depends on BINMAN - default y if OF_BOARD - help - This option tells U-Boot build system that a standalone device tree - source is explicitly required when using binman to package U-Boot. - - This is not necessary in a common scenario where a device tree source - that contains the binman node is provided in the arch/<arch>/dts - directory for a specific board. Such device tree sources are built for - OF_SEPARATE or OF_EMBED. However for a scenario like the board device - tree blob is not provided in the U-Boot build tree, but fed to U-Boot - in the runtime, e.g.: in the OF_BOARD case that it is passed by - a prior stage bootloader. For such scenario, a standalone device tree - blob containing binman node to describe how to package U-Boot should - be provided explicitly. - menu "Device Tree Control" depends on SUPPORT_OF_CONTROL @@ -97,11 +79,9 @@ config OF_LIVE choice prompt "Provider of DTB for DT control" depends on OF_CONTROL - default OF_BOARD if SANDBOX config OF_SEPARATE bool "Separate DTB for DT control" - depends on !SANDBOX help If this option is enabled, the device tree will be built and placed as a separate u-boot.dtb file alongside the U-Boot image. @@ -114,14 +94,50 @@ config OF_EMBED and development only and is not recommended for production devices. Boards in the mainline U-Boot tree should not use it. +endchoice + config OF_BOARD bool "Provided by the board (e.g a previous loader) at runtime" + default y if SANDBOX || OF_HAS_PRIOR_STAGE help - If this option is enabled, the device tree will be provided by - the board at runtime if the board supports it, instead of being - bundled with the image. + If this option is enabled, the device tree is provided at runtime by + a custom function called board_fdt_blob_setup(). The board must + implement this function if it wishes to provide special behaviour. -endchoice + With this option, the device tree build by U-Boot may be overridden or + ignored. See OF_HAS_PRIOR_STAGE. + + Note: Boards which use this to handle a device tree passed from an + earlier stage should enable OF_HAS_PRIOR_STAGE. + +config OF_HAS_PRIOR_STAGE + bool + help + Indicates that a prior stage of the firmware (before U-Boot proper) + makes use of device tree and this board normally boots with that prior + stage, that provides a devicetree to U-Boot. + + This means that the device tree built in U-Boot should not be packaged + in the firmware image. Instead, the prior stage's device tree should + be so packaged. At runtime, the prior stage reads this, does any + necessary fix-ups, then passes it to U-Boot. See OF_BOARD. + + This option does not preclude using the U-Boot device tree, e.g. for + development purposes, but it is not recommended, and likely will not + even work, for production systems. + + Note: This option must be set in Kconfig and cannot be enabled or + disabled in the board's defconfig file. + +config OF_OMIT_DTB + bool "Omit the device tree output when building" + default y if OF_HAS_PRIOR_STAGE && !BINMAN + help + As a special case, avoid writing a device tree file u-boot.dtb when + building. Also don't include that file in u-boot.bin + + This is used for boards which normally provide a devicetree via a + runtime mechanism (such as OF_BOARD), to avoid confusion. config DEFAULT_DEVICE_TREE string "Default Device Tree for DT control" @@ -194,7 +210,6 @@ endchoice config MULTI_DTB_FIT_UNCOMPRESS_SZ hex "Size of memory reserved to uncompress the DTBs" - depends on (MULTI_DTB_FIT_GZIP || MULTI_DTB_FIT_LZO) default 0x8000 help This is the size of this area where the DTBs are uncompressed. diff --git a/include/asm-generic/global_data.h b/include/asm-generic/global_data.h index 16fd305..104282b 100644 --- a/include/asm-generic/global_data.h +++ b/include/asm-generic/global_data.h @@ -244,6 +244,10 @@ struct global_data { * @fdt_size: space reserved for relocated device space */ unsigned long fdt_size; + /** + * @fdt_src: Source of FDT + */ + enum fdt_source_t fdt_src; #if CONFIG_IS_ENABLED(OF_LIVE) /** * @of_root: root node of the live tree @@ -512,6 +516,14 @@ static_assert(sizeof(struct global_data) == GD_SIZE); #define gd_acpi_ctx() NULL #endif +#if CONFIG_IS_ENABLED(MULTI_DTB_FIT) +#define gd_multi_dtb_fit() gd->multi_dtb_fit +#define gd_set_multi_dtb_fit(_dtb) gd->multi_dtb_fit = _dtb +#else +#define gd_multi_dtb_fit() NULL +#define gd_set_multi_dtb_fit(_dtb) +#endif + /** * enum gd_flags - global data flags * diff --git a/include/dm/device.h b/include/dm/device.h index 544734e..cf785f7 100644 --- a/include/dm/device.h +++ b/include/dm/device.h @@ -593,7 +593,7 @@ int device_get_child(const struct udevice *parent, int index, struct udevice **devp); /** - * device_get_child_count() - Get the available child count of a device + * device_get_child_count() - Get the child count of a device * * Returns the number of children to a device. * @@ -602,6 +602,15 @@ int device_get_child(const struct udevice *parent, int index, int device_get_child_count(const struct udevice *parent); /** + * device_get_decendent_count() - Get the total number of decendents of a device + * + * Returns the total number of decendents, including all children + * + * @parent: Parent device to check + */ +int device_get_decendent_count(const struct udevice *parent); + +/** * device_find_child_by_seq() - Find a child device based on a sequence * * This searches for a device with the given seq. diff --git a/include/dm/root.h b/include/dm/root.h index 42510b1..780f269 100644 --- a/include/dm/root.h +++ b/include/dm/root.h @@ -131,4 +131,12 @@ int dm_remove_devices_flags(uint flags); static inline int dm_remove_devices_flags(uint flags) { return 0; } #endif +/** + * dm_get_stats() - Get some stats for driver mode + * + * @device_countp: Returns total number of devices that are bound + * @uclass_countp: Returns total number of uclasses in use + */ +void dm_get_stats(int *device_countp, int *uclass_countp); + #endif diff --git a/include/dm/uclass-internal.h b/include/dm/uclass-internal.h index 49808c5..fb0edcc 100644 --- a/include/dm/uclass-internal.h +++ b/include/dm/uclass-internal.h @@ -307,6 +307,13 @@ static inline int uclass_pre_remove_device(struct udevice *dev) { return 0; } #endif /** + * uclass_get_count() - Get the number of uclasses + * + * Returns the number of uclasses instantiated in driver model + */ +int uclass_get_count(void); + +/** * uclass_find() - Find uclass by its id * * @id: Id to serach for diff --git a/include/dt-bindings/clock/bcm2835.h b/include/dt-bindings/clock/bcm2835.h index 2cec01f..b60c034 100644 --- a/include/dt-bindings/clock/bcm2835.h +++ b/include/dt-bindings/clock/bcm2835.h @@ -58,3 +58,5 @@ #define BCM2835_CLOCK_DSI1E 48 #define BCM2835_CLOCK_DSI0P 49 #define BCM2835_CLOCK_DSI1P 50 + +#define BCM2711_CLOCK_EMMC2 51 diff --git a/include/fdtdec.h b/include/fdtdec.h index 6c7ab88..09525ce 100644 --- a/include/fdtdec.h +++ b/include/fdtdec.h @@ -55,6 +55,31 @@ struct bd_info; #define SPL_BUILD 0 #endif +/** + * enum fdt_source_t - indicates where the devicetree came from + * + * These are listed in approximate order of desirability after FDTSRC_NONE + * + * @FDTSRC_SEPARATE: Appended to U-Boot. This is the normal approach if U-Boot + * is the only firmware being booted + * @FDTSRC_FIT: Found in a multi-dtb FIT. This should be used when U-Boot must + * select a devicetree from many options + * @FDTSRC_BOARD: Located by custom board code. This should only be used when + * the prior stage does not support FDTSRC_PASSAGE + * @FDTSRC_EMBED: Embedded into U-Boot executable. This should onyl be used when + * U-Boot is packaged as an ELF file, e.g. for debugging purposes + * @FDTSRC_ENV: Provided by the fdtcontroladdr environment variable. This should + * be used for debugging/development only + * @FDTSRC_NONE: No devicetree at all + */ +enum fdt_source_t { + FDTSRC_SEPARATE, + FDTSRC_FIT, + FDTSRC_BOARD, + FDTSRC_EMBED, + FDTSRC_ENV, +}; + /* * Information about a resource. start is the first address of the resource * and end is the last address (inclusive). The length of the resource will @@ -111,6 +136,20 @@ struct fdt_pci_addr { extern u8 __dtb_dt_begin[]; /* embedded device tree blob */ extern u8 __dtb_dt_spl_begin[]; /* embedded device tree blob for SPL/TPL */ +/* Get a pointer to the embedded devicetree, if there is one, else NULL */ +static inline u8 *dtb_dt_embedded(void) +{ +#ifdef CONFIG_OF_EMBED +# ifdef CONFIG_SPL_BUILD + return __dtb_dt_spl_begin; +# else + return __dtb_dt_begin; +# endif +#else + return NULL; +#endif +} + /** * Compute the size of a resource. * @@ -1156,10 +1195,13 @@ int fdtdec_resetup(int *rescan); /** * Board-specific FDT initialization. Returns the address to a device tree blob. - * Called when CONFIG_OF_BOARD is defined, or if CONFIG_OF_SEPARATE is defined - * and the board implements it. + * + * Called when CONFIG_OF_BOARD is defined. + * + * The existing devicetree is available at gd->fdt_blob * * @err internal error code if we fail to setup a DTB + * @returns new devicetree blob pointer */ void *board_fdt_blob_setup(int *err); @@ -1198,4 +1240,11 @@ int fdtdec_decode_ram_size(const void *blob, const char *area, int board_id, phys_addr_t *basep, phys_size_t *sizep, struct bd_info *bd); +/** + * fdtdec_get_srcname() - Get the name of where the devicetree comes from + * + * @return source name + */ +const char *fdtdec_get_srcname(void); + #endif diff --git a/lib/fdtdec.c b/lib/fdtdec.c index 7681f27..280cda6 100644 --- a/lib/fdtdec.c +++ b/lib/fdtdec.c @@ -76,6 +76,19 @@ static const char * const compat_names[COMPAT_COUNT] = { COMPAT(ALTERA_SOCFPGA_CLK_INIT, "altr,socfpga-a10-clk-init") }; +static const char *const fdt_src_name[] = { + [FDTSRC_SEPARATE] = "separate", + [FDTSRC_FIT] = "fit", + [FDTSRC_BOARD] = "board", + [FDTSRC_EMBED] = "embed", + [FDTSRC_ENV] = "env", +}; + +const char *fdtdec_get_srcname(void) +{ + return fdt_src_name[gd->fdt_src]; +} + const char *fdtdec_get_compatible(enum fdt_compat_id id) { /* We allow reading of the 'unknown' ID for testing purposes */ @@ -1146,11 +1159,10 @@ int fdtdec_setup_mem_size_base_lowest(void) return 0; } -#if CONFIG_IS_ENABLED(MULTI_DTB_FIT) -# if CONFIG_IS_ENABLED(MULTI_DTB_FIT_GZIP) ||\ - CONFIG_IS_ENABLED(MULTI_DTB_FIT_LZO) static int uncompress_blob(const void *src, ulong sz_src, void **dstp) { +#if CONFIG_IS_ENABLED(MULTI_DTB_FIT_GZIP) ||\ + CONFIG_IS_ENABLED(MULTI_DTB_FIT_LZO) size_t sz_out = CONFIG_VAL(MULTI_DTB_FIT_UNCOMPRESS_SZ); bool gzip = 0, lzo = 0; ulong sz_in = sz_src; @@ -1175,11 +1187,11 @@ static int uncompress_blob(const void *src, ulong sz_src, void **dstp) return -ENOMEM; } } else { -# if CONFIG_IS_ENABLED(MULTI_DTB_FIT_USER_DEFINED_AREA) +# if CONFIG_IS_ENABLED(MULTI_DTB_FIT_USER_DEFINED_AREA) dst = (void *)CONFIG_VAL(MULTI_DTB_FIT_USER_DEF_ADDR); -# else +# else return -ENOTSUPP; -# endif +# endif } if (CONFIG_IS_ENABLED(GZIP) && gzip) @@ -1197,27 +1209,22 @@ static int uncompress_blob(const void *src, ulong sz_src, void **dstp) return -EBADMSG; } *dstp = dst; - return 0; -} -# else -static int uncompress_blob(const void *src, ulong sz_src, void **dstp) -{ +#else + *dstp = (void *)src; *dstp = (void *)src; +#endif return 0; } -# endif -#endif -#if defined(CONFIG_OF_BOARD) || defined(CONFIG_OF_SEPARATE) -/* - * For CONFIG_OF_SEPARATE, the board may optionally implement this to - * provide and/or fixup the fdt. +/** + * fdt_find_separate() - Find a devicetree at the end of the image + * + * @return pointer to FDT blob */ -__weak void *board_fdt_blob_setup(int *err) +static void *fdt_find_separate(void) { void *fdt_blob = NULL; - *err = 0; #ifdef CONFIG_SPL_BUILD /* FDT is at end of BSS unless it is in a different memory region */ if (IS_ENABLED(CONFIG_SPL_SEPARATE_BSS)) @@ -1231,7 +1238,6 @@ __weak void *board_fdt_blob_setup(int *err) return fdt_blob; } -#endif int fdtdec_set_ethernet_mac_address(void *fdt, const u8 *mac, size_t size) { @@ -1589,60 +1595,81 @@ int fdtdec_set_carveout(void *blob, const char *node, const char *prop_name, return 0; } +/* TODO(sjg@chromium.org): This function should not be weak */ __weak int fdtdec_board_setup(const void *fdt_blob) { return 0; } -int fdtdec_setup(void) +/** + * setup_multi_dtb_fit() - locate the correct dtb from a FIT + * + * This supports the CONFIG_MULTI_DTB_FIT feature, looking for the dtb in a + * supplied FIT + * + * It accepts the current value of gd->fdt_blob, which points to the FIT, then + * updates that gd->fdt_blob, to point to the chosen dtb so that U-Boot uses the + * correct one + */ +static void setup_multi_dtb_fit(void) { - int ret; -#if CONFIG_IS_ENABLED(OF_CONTROL) -# if CONFIG_IS_ENABLED(MULTI_DTB_FIT) - void *fdt_blob; -# endif -# ifdef CONFIG_OF_EMBED - /* Get a pointer to the FDT */ -# ifdef CONFIG_SPL_BUILD - gd->fdt_blob = __dtb_dt_spl_begin; -# else - gd->fdt_blob = __dtb_dt_begin; -# endif -# elif defined(CONFIG_OF_BOARD) || defined(CONFIG_OF_SEPARATE) - /* Allow the board to override the fdt address. */ - gd->fdt_blob = board_fdt_blob_setup(&ret); - if (ret) - return ret; -# endif -# ifndef CONFIG_SPL_BUILD - /* Allow the early environment to override the fdt address */ - gd->fdt_blob = map_sysmem - (env_get_ulong("fdtcontroladdr", 16, - (unsigned long)map_to_sysmem(gd->fdt_blob)), 0); -# endif + void *blob; -# if CONFIG_IS_ENABLED(MULTI_DTB_FIT) /* * Try and uncompress the blob. * Unfortunately there is no way to know how big the input blob really * is. So let us set the maximum input size arbitrarily high. 16MB * ought to be more than enough for packed DTBs. */ - if (uncompress_blob(gd->fdt_blob, 0x1000000, &fdt_blob) == 0) - gd->fdt_blob = fdt_blob; + if (uncompress_blob(gd->fdt_blob, 0x1000000, &blob) == 0) + gd->fdt_blob = blob; /* * Check if blob is a FIT images containings DTBs. * If so, pick the most relevant */ - fdt_blob = locate_dtb_in_fit(gd->fdt_blob); - if (fdt_blob) { - gd->multi_dtb_fit = gd->fdt_blob; - gd->fdt_blob = fdt_blob; + blob = locate_dtb_in_fit(gd->fdt_blob); + if (blob) { + gd_set_multi_dtb_fit(gd->fdt_blob); + gd->fdt_blob = blob; + gd->fdt_src = FDTSRC_FIT; } +} -# endif -#endif +int fdtdec_setup(void) +{ + int ret; + + /* The devicetree is typically appended to U-Boot */ + if (IS_ENABLED(CONFIG_OF_SEPARATE)) { + gd->fdt_blob = fdt_find_separate(); + gd->fdt_src = FDTSRC_SEPARATE; + } else { /* embed dtb in ELF file for testing / development */ + gd->fdt_blob = dtb_dt_embedded(); + gd->fdt_src = FDTSRC_EMBED; + } + + /* Allow the board to override the fdt address. */ + if (IS_ENABLED(CONFIG_OF_BOARD)) { + gd->fdt_blob = board_fdt_blob_setup(&ret); + if (ret) + return ret; + gd->fdt_src = FDTSRC_BOARD; + } + + /* Allow the early environment to override the fdt address */ + if (!IS_ENABLED(CONFIG_SPL_BUILD)) { + ulong addr; + + addr = env_get_hex("fdtcontroladdr", 0); + if (addr) { + gd->fdt_blob = map_sysmem(addr, 0); + gd->fdt_src = FDTSRC_ENV; + } + } + + if (CONFIG_IS_ENABLED(MULTI_DTB_FIT)) + setup_multi_dtb_fit(); ret = fdtdec_prepare_fdt(); if (!ret) @@ -1650,7 +1677,6 @@ int fdtdec_setup(void) return ret; } -#if CONFIG_IS_ENABLED(MULTI_DTB_FIT) int fdtdec_resetup(int *rescan) { void *fdt_blob; @@ -1661,8 +1687,8 @@ int fdtdec_resetup(int *rescan) * FIT image stillpresent there. Save the time and space * required to uncompress it again. */ - if (gd->multi_dtb_fit) { - fdt_blob = locate_dtb_in_fit(gd->multi_dtb_fit); + if (gd_multi_dtb_fit()) { + fdt_blob = locate_dtb_in_fit(gd_multi_dtb_fit()); if (fdt_blob == gd->fdt_blob) { /* @@ -1686,7 +1712,6 @@ int fdtdec_resetup(int *rescan) *rescan = 0; return 0; } -#endif int fdtdec_decode_ram_size(const void *blob, const char *area, int board_id, phys_addr_t *basep, phys_size_t *sizep, diff --git a/scripts/Makefile.lib b/scripts/Makefile.lib index 39f0339..b4e63bc 100644 --- a/scripts/Makefile.lib +++ b/scripts/Makefile.lib @@ -175,7 +175,9 @@ u_boot_dtsi_options_raw = $(warning Automatic .dtsi inclusion: options: \ # Uncomment for debugging # This shows all the files that were considered and the one that we chose. -# u_boot_dtsi_options_debug = $(u_boot_dtsi_options_raw) +ifdef DEVICE_TREE_DEBUG +u_boot_dtsi_options_debug = $(warning $(u_boot_dtsi_options_raw)) +endif # We use the first match u_boot_dtsi = $(strip $(u_boot_dtsi_options_debug) \ diff --git a/scripts/check-of.sh b/scripts/check-of.sh new file mode 100755 index 0000000..0f0bf51 --- /dev/null +++ b/scripts/check-of.sh @@ -0,0 +1,42 @@ +#!/bin/sh +# Copyright 2021 Google LLC +# Written by Simon Glass <sjg@chromium.org> +# +# Check that the .config file provided does not try to disable OF_BOARD for +# boards that use CONFIG_OF_HAS_PRIOR_STAGE +# +# Usage +# check-of.sh <path to .config> <path to allowlist file> +# +# For example: +# scripts/check-of.sh b/chromebook_link/u-boot.cfg kconfig_allowlist.txt +# +# Exit code is 0 if OK, 3 if the .config is wrong, as above + +set -e +set -u + +PROG_NAME="${0##*/}" + +usage() { + echo "$PROG_NAME <path to .config> <path to allowlist file>" + exit 1 +} + +[ $# -ge 2 ] || usage + +path="$1" +allowlist="$2" + +sys_config="$(sed -n 's/CONFIG_SYS_CONFIG_NAME="\(.*\)"$/\1/p' "${path}")" + +if grep -q OF_HAS_PRIOR_STAGE=y "${path}"; then + if ! grep -lq CONFIG_OF_BOARD=y "${path}"; then + echo >&2 "This board uses a prior stage to provide the device tree." + echo >&2 "Please enable CONFIG_OF_BOARD to ensure that it works correctly." + if grep -q "${sys_config}" "${allowlist}"; then + exit 0 + fi + exit 3 + fi +fi diff --git a/scripts/of_allowlist.txt b/scripts/of_allowlist.txt new file mode 100644 index 0000000..e82cf55 --- /dev/null +++ b/scripts/of_allowlist.txt @@ -0,0 +1 @@ +# List of boards which are permitted to use OF_HAS_PRIOR_STAGE without OF_BOARD diff --git a/test/dm/core.c b/test/dm/core.c index c9a7606..c76dfdb 100644 --- a/test/dm/core.c +++ b/test/dm/core.c @@ -307,11 +307,15 @@ static int dm_test_lifecycle(struct unit_test_state *uts) { int op_count[DM_TEST_OP_COUNT]; struct udevice *dev, *test_dev; + int start_dev_count, start_uc_count; + int dev_count, uc_count; int pingret; int ret; memcpy(op_count, dm_testdrv_op_count, sizeof(op_count)); + dm_get_stats(&start_dev_count, &start_uc_count); + ut_assertok(device_bind_by_name(uts->root, false, &driver_info_manual, &dev)); ut_assert(dev); @@ -319,6 +323,11 @@ static int dm_test_lifecycle(struct unit_test_state *uts) == op_count[DM_TEST_OP_BIND] + 1); ut_assert(!dev_get_priv(dev)); + /* We should have one more device */ + dm_get_stats(&dev_count, &uc_count); + ut_asserteq(start_dev_count + 1, dev_count); + ut_asserteq(start_uc_count, uc_count); + /* Probe the device - it should fail allocating private data */ uts->force_fail_alloc = 1; ret = device_probe(dev); @@ -353,6 +362,11 @@ static int dm_test_lifecycle(struct unit_test_state *uts) ut_asserteq(1, dm_testdrv_op_count[DM_TEST_OP_UNBIND]); ut_asserteq(1, dm_testdrv_op_count[DM_TEST_OP_PRE_UNBIND]); + /* We should have one less device */ + dm_get_stats(&dev_count, &uc_count); + ut_asserteq(start_dev_count, dev_count); + ut_asserteq(start_uc_count, uc_count); + return 0; } DM_TEST(dm_test_lifecycle, UT_TESTF_SCAN_PDATA | UT_TESTF_PROBE_TEST); @@ -526,17 +540,31 @@ DM_TEST(dm_test_leak, 0); /* Test uclass init/destroy methods */ static int dm_test_uclass(struct unit_test_state *uts) { + int dev_count, uc_count; struct uclass *uc; + /* We should have just the root device and uclass */ + dm_get_stats(&dev_count, &uc_count); + ut_asserteq(1, dev_count); + ut_asserteq(1, uc_count); + ut_assertok(uclass_get(UCLASS_TEST, &uc)); ut_asserteq(1, dm_testdrv_op_count[DM_TEST_OP_INIT]); ut_asserteq(0, dm_testdrv_op_count[DM_TEST_OP_DESTROY]); ut_assert(uclass_get_priv(uc)); + dm_get_stats(&dev_count, &uc_count); + ut_asserteq(1, dev_count); + ut_asserteq(2, uc_count); + ut_assertok(uclass_destroy(uc)); ut_asserteq(1, dm_testdrv_op_count[DM_TEST_OP_INIT]); ut_asserteq(1, dm_testdrv_op_count[DM_TEST_OP_DESTROY]); + dm_get_stats(&dev_count, &uc_count); + ut_asserteq(1, dev_count); + ut_asserteq(1, uc_count); + return 0; } DM_TEST(dm_test_uclass, 0); @@ -1217,3 +1245,16 @@ static int dm_test_dma_offset(struct unit_test_state *uts) } DM_TEST(dm_test_dma_offset, UT_TESTF_SCAN_PDATA | UT_TESTF_SCAN_FDT); #endif + +/* Test dm_get_stats() */ +static int dm_test_get_stats(struct unit_test_state *uts) +{ + int dev_count, uc_count; + + dm_get_stats(&dev_count, &uc_count); + ut_assert(dev_count > 50); + ut_assert(uc_count > 30); + + return 0; +} +DM_TEST(dm_test_get_stats, UT_TESTF_SCAN_FDT); diff --git a/tools/binman/binman.rst b/tools/binman/binman.rst index 10389a5..3e063d1 100644 --- a/tools/binman/binman.rst +++ b/tools/binman/binman.rst @@ -232,26 +232,6 @@ You can use other, more specific CONFIG options - see 'Automatic .dtsi inclusion' below. -Using binman with OF_BOARD --------------------------------------------- - -Normally binman is used with a board configured with OF_SEPARATE or OF_EMBED. -This is a typical scenario where a device tree source that contains the binman -node is provided in the arch/<arch>/dts directory for a specific board. - -However for a board configured with OF_BOARD, no device tree blob is provided -in the U-Boot build phase hence the binman node information is not available. -In order to support such use case, a new Kconfig option BINMAN_STANDALONE_FDT -is introduced, to tell the build system that a standalone device tree blob -containing binman node is explicitly required. - -Note there is a Kconfig option BINMAN_FDT which enables U-Boot run time to -access information about binman entries, stored in the device tree in a binman -node. Generally speaking, this option makes sense for OF_SEPARATE or OF_EMBED. -For the other OF_CONTROL methods, it's quite possible binman node is not -available as binman is invoked during the build phase, thus this option is not -turned on by default for these OF_CONTROL methods. - Access to binman entry offsets at run time (symbols) ---------------------------------------------------- @@ -810,12 +790,14 @@ Binman will search for the following files in arch/<arch>/dts:: U-Boot will only use the first one that it finds. If you need to include a more general file you can do that from the more specific file using #include. -If you are having trouble figuring out what is going on, you can uncomment -the 'warning' line in scripts/Makefile.lib to see what it has found:: - - # Uncomment for debugging - # This shows all the files that were considered and the one that we chose. - # u_boot_dtsi_options_debug = $(u_boot_dtsi_options_raw) +If you are having trouble figuring out what is going on, you can use +`DEVICE_TREE_DEBUG=1` with your build:: + + make DEVICE_TREE_DEBUG=1 + scripts/Makefile.lib:334: Automatic .dtsi inclusion: options: + arch/arm/dts/juno-r2-u-boot.dtsi arch/arm/dts/-u-boot.dtsi + arch/arm/dts/armv8-u-boot.dtsi arch/arm/dts/armltd-u-boot.dtsi + arch/arm/dts/u-boot.dtsi ... found: "arch/arm/dts/juno-r2-u-boot.dtsi" Updating an ELF file |