mpc8260: remove atc board support

These boards are still non-generic boards.

drivers/rtc/ds12887.c should also be removed because it can not
be built without CONFIG_ATC.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>

2 files changed, 0 insertions, 491 deletions

diff --git a/include/configs/atc.h b/include/configs/atc.h
deleted file mode 100644
index 77fa79a..0000000
--- a/include/configs/atc.h
+++ /dev/null
@@ -1,489 +0,0 @@
-/*
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_ATC		1	/* ...on a ATC board	*/
-#define CONFIG_CPM2		1	/* Has a CPM2 */
-
-#define	CONFIG_SYS_TEXT_BASE	0xFF000000
-
-/*
- * select serial console configuration
- *
- * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
- * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
- * for SCC).
- *
- * if CONFIG_CONS_NONE is defined, then the serial console routines must
- * defined elsewhere (for example, on the cogent platform, there are serial
- * ports on the motherboard which are used for the serial console - see
- * cogent/cma101/serial.[ch]).
- */
-#define  CONFIG_CONS_ON_SMC		/* define if console on SMC */
-#undef CONFIG_CONS_ON_SCC		/* define if console on SCC */
-#undef  CONFIG_CONS_NONE		/* define if console on something else*/
-#define CONFIG_CONS_INDEX	2	/* which serial channel for console */
-
-#define CONFIG_BAUDRATE		115200
-
-/*
- * select ethernet configuration
- *
- * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
- * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
- * for FCC)
- *
- * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
- * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
- */
-#undef	CONFIG_ETHER_ON_SCC		/* define if ether on SCC       */
-#undef	CONFIG_ETHER_NONE		/* define if ether on something else */
-#define CONFIG_ETHER_ON_FCC
-
-#define CONFIG_ETHER_ON_FCC2
-
-/*
- * - Rx-CLK is CLK13
- * - Tx-CLK is CLK14
- * - RAM for BD/Buffers is on the 60x Bus (see 28-13)
- * - Enable Full Duplex in FSMR
- */
-# define CONFIG_SYS_CMXFCR_MASK2	(CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)
-# define CONFIG_SYS_CMXFCR_VALUE2	(CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14)
-# define CONFIG_SYS_CPMFCR_RAMTYPE	0
-# define CONFIG_SYS_FCC_PSMR		(FCC_PSMR_FDE|FCC_PSMR_LPB)
-
-#define CONFIG_ETHER_ON_FCC3
-
-/*
- * - Rx-CLK is CLK15
- * - Tx-CLK is CLK16
- * - RAM for BD/Buffers is on the local Bus (see 28-13)
- * - Enable Half Duplex in FSMR
- */
-# define CONFIG_SYS_CMXFCR_MASK3	(CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK)
-# define CONFIG_SYS_CMXFCR_VALUE3	(CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16)
-
-/* system clock rate (CLKIN) - equal to the 60x and local bus speed */
-#define CONFIG_8260_CLKIN	64000000	/* in Hz */
-
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-
-#undef	CONFIG_CLOCKS_IN_MHZ		/* clocks passsed to Linux in Hz */
-
-#define CONFIG_PREBOOT							\
-	"echo;"								\
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;"\
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND						\
-	"bootp;"							\
-	"setenv bootargs root=/dev/nfs rw "				\
-	"nfsroot=${serverip}:${rootpath} "				\
-	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;"\
-	"bootm"
-
-/*-----------------------------------------------------------------------
- * Miscellaneous configuration options
- */
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PCMCIA
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_IDE
-
-
-#define CONFIG_DOS_PARTITION
-
-/*
- * Miscellaneous configurable options
- */
-#define	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END	0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-#define	CONFIG_SYS_LOAD_ADDR	0x100000	/* default load address	*/
-
-#define CONFIG_SYS_PIO_MODE		0	/* IDE interface in PIO Mode 0	*/
-
-#define	CONFIG_SYS_RESET_ADDRESS 0xFFF00100	/* "bad" address		*/
-
-#define CONFIG_SYS_ALLOC_DPRAM
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-#define CONFIG_SPI
-
-#define CONFIG_RTC_DS12887
-
-#define RTC_BASE_ADDR		0xF5000000
-#define RTC_PORT_ADDR		RTC_BASE_ADDR + 0x800
-#define RTC_PORT_DATA		RTC_BASE_ADDR + 0x808
-
-#define CONFIG_MISC_INIT_R
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * Flash configuration
- */
-
-#define CONFIG_SYS_FLASH_BASE		0xFF000000
-#define CONFIG_SYS_FLASH_SIZE		0x00800000
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max num of memory banks      */
-#define CONFIG_SYS_MAX_FLASH_SECT	128	/* max num of sects on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	240000	/* Flash Erase Timeout (in ms)  */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (in ms)  */
-
-#define CONFIG_FLASH_16BIT
-
-/*-----------------------------------------------------------------------
- * Hard Reset Configuration Words
- *
- * if you change bits in the HRCW, you must also change the CONFIG_SYS_*
- * defines for the various registers affected by the HRCW e.g. changing
- * HRCW_DPPCxx requires you to also change CONFIG_SYS_SIUMCR.
- */
-#define CONFIG_SYS_HRCW_MASTER		(HRCW_CIP | HRCW_ISB100 | HRCW_BMS | \
-				 HRCW_BPS10 |\
-				 HRCW_APPC10)
-
-/* no slaves so just fill with zeros */
-#define CONFIG_SYS_HRCW_SLAVE1		0
-#define CONFIG_SYS_HRCW_SLAVE2		0
-#define CONFIG_SYS_HRCW_SLAVE3		0
-#define CONFIG_SYS_HRCW_SLAVE4		0
-#define CONFIG_SYS_HRCW_SLAVE5		0
-#define CONFIG_SYS_HRCW_SLAVE6		0
-#define CONFIG_SYS_HRCW_SLAVE7		0
-
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xF0000000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE	0x2F00  /* Size of used area in DPRAM    */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- *
- * 60x SDRAM is mapped at CONFIG_SYS_SDRAM_BASE.
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_SDRAM_MAX_SIZE	0x08000000	/* max. 128 MB		*/
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN		(192 << 10)	/* Reserve 192 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()*/
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-# define CONFIG_SYS_RAMBOOT
-#endif
-
-#define	CONFIG_PCI
-#define CONFIG_PCI_INDIRECT_BRIDGE
-#define	CONFIG_PCI_PNP
-#define	CONFIG_SYS_PCI_MSTR_IO_BUS	0x00000000	/* PCI base   */
-
-#if 1
-/* environment is in Flash */
-#define CONFIG_ENV_IS_IN_FLASH	1
-# define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE+0x30000)
-# define CONFIG_ENV_SIZE		0x10000
-# define CONFIG_ENV_SECT_SIZE	0x10000
-#else
-#define CONFIG_ENV_IS_IN_EEPROM	1
-#define CONFIG_ENV_OFFSET		0
-#define CONFIG_ENV_SIZE		2048
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	4	/* 16-byte page size	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE      32      /* For MPC8260 CPU              */
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * HIDx - Hardware Implementation-dependent Registers                    2-11
- *-----------------------------------------------------------------------
- * HID0 also contains cache control - initially enable both caches and
- * invalidate contents, then the final state leaves only the instruction
- * cache enabled. Note that Power-On and Hard reset invalidate the caches,
- * but Soft reset does not.
- *
- * HID1 has only read-only information - nothing to set.
- */
-#define CONFIG_SYS_HID0_INIT   (HID0_ICE|HID0_DCE|HID0_ICFI|\
-			 HID0_DCI|HID0_IFEM|HID0_ABE)
-#define CONFIG_SYS_HID0_FINAL  (HID0_IFEM|HID0_ABE)
-#define CONFIG_SYS_HID2        0
-
-/*-----------------------------------------------------------------------
- * RMR - Reset Mode Register                                     5-5
- *-----------------------------------------------------------------------
- * turn on Checkstop Reset Enable
- */
-#define CONFIG_SYS_RMR         RMR_CSRE
-
-/*-----------------------------------------------------------------------
- * BCR - Bus Configuration                                       4-25
- *-----------------------------------------------------------------------
- */
-#define BCR_APD01	0x10000000
-#define CONFIG_SYS_BCR		(BCR_APD01|BCR_ETM|BCR_LETM)	/* 8260 mode */
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration                             4-31
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_SIUMCR      (SIUMCR_BBD|SIUMCR_APPC10|\
-			 SIUMCR_CS10PC00|SIUMCR_BCTLC10)
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control                             4-35
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR       (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
-			 SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
-#else
-#define CONFIG_SYS_SYPCR       (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
-			 SYPCR_SWRI|SYPCR_SWP)
-#endif /* CONFIG_WATCHDOG */
-
-/*-----------------------------------------------------------------------
- * TMCNTSC - Time Counter Status and Control                     4-40
- *-----------------------------------------------------------------------
- * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
- * and enable Time Counter
- */
-#define CONFIG_SYS_TMCNTSC     (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control                 4-42
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
- * Periodic timer
- */
-#define CONFIG_SYS_PISCR       (PISCR_PS|PISCR_PTF|PISCR_PTE)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock Control                                   9-8
- *-----------------------------------------------------------------------
- * Ensure DFBRG is Divide by 16
- */
-#define CONFIG_SYS_SCCR        SCCR_DFBRG01
-
-/*-----------------------------------------------------------------------
- * RCCR - RISC Controller Configuration                         13-7
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RCCR        0
-
-#define CONFIG_SYS_MIN_AM_MASK	0xC0000000
-/*-----------------------------------------------------------------------
- * MPTPR - Memory Refresh Timer Prescaler Register              10-18
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_MPTPR       0x1F00
-
-/*-----------------------------------------------------------------------
- * PSRT - Refresh Timer Register                                10-16
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_PSRT        0x0f
-
-/*-----------------------------------------------------------------------
- * PSRT - SDRAM Mode Register                                   10-10
- *-----------------------------------------------------------------------
- */
-
-	/* SDRAM initialization values for 8-column chips
-	 */
-#define CONFIG_SYS_OR2_8COL	(CONFIG_SYS_MIN_AM_MASK		|\
-			 ORxS_BPD_4			|\
-			 ORxS_ROWST_PBI1_A7		|\
-			 ORxS_NUMR_12)
-
-#define CONFIG_SYS_PSDMR_8COL	(PSDMR_PBI			|\
-			 PSDMR_SDAM_A15_IS_A5		|\
-			 PSDMR_BSMA_A15_A17		|\
-			 PSDMR_SDA10_PBI1_A7		|\
-			 PSDMR_RFRC_7_CLK		|\
-			 PSDMR_PRETOACT_3W		|\
-			 PSDMR_ACTTORW_2W		|\
-			 PSDMR_LDOTOPRE_1C		|\
-			 PSDMR_WRC_1C			|\
-			 PSDMR_CL_2)
-
-	/* SDRAM initialization values for 9-column chips
-	 */
-#define CONFIG_SYS_OR2_9COL	(CONFIG_SYS_MIN_AM_MASK		|\
-			 ORxS_BPD_4			|\
-			 ORxS_ROWST_PBI1_A6		|\
-			 ORxS_NUMR_12)
-
-#define CONFIG_SYS_PSDMR_9COL	(PSDMR_PBI			|\
-			 PSDMR_SDAM_A16_IS_A5		|\
-			 PSDMR_BSMA_A15_A17		|\
-			 PSDMR_SDA10_PBI1_A6		|\
-			 PSDMR_RFRC_7_CLK		|\
-			 PSDMR_PRETOACT_3W		|\
-			 PSDMR_ACTTORW_2W		|\
-			 PSDMR_LDOTOPRE_1C		|\
-			 PSDMR_WRC_1C			|\
-			 PSDMR_CL_2)
-
-/*
- * Init Memory Controller:
- *
- * Bank Bus     Machine PortSz  Device
- * ---- ---     ------- ------  ------
- *  0   60x     GPCM    8  bit  Boot ROM
- *  1   60x     GPCM    64 bit  FLASH
- *  2   60x     SDRAM   64 bit  SDRAM
- *
- */
-
-#define CONFIG_SYS_MRS_OFFS	0x00000000
-
-/* Bank 0 - FLASH
- */
-#define CONFIG_SYS_BR0_PRELIM  ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK)  |\
-			 BRx_PS_16                      |\
-			 BRx_MS_GPCM_P                  |\
-			 BRx_V)
-
-#define CONFIG_SYS_OR0_PRELIM  (P2SZ_TO_AM(CONFIG_SYS_FLASH_SIZE)     |\
-			 ORxG_CSNT                      |\
-			 ORxG_ACS_DIV1                  |\
-			 ORxG_SCY_3_CLK                 |\
-			 ORxU_EHTR_8IDLE)
-
-
-/* Bank 2 - 60x bus SDRAM
- */
-#ifndef CONFIG_SYS_RAMBOOT
-#define CONFIG_SYS_BR2_PRELIM  ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK)  |\
-			 BRx_PS_64                      |\
-			 BRx_MS_SDRAM_P                 |\
-			 BRx_V)
-
-#define CONFIG_SYS_OR2_PRELIM	 CONFIG_SYS_OR2_8COL
-
-#define CONFIG_SYS_PSDMR	 CONFIG_SYS_PSDMR_8COL
-#endif /* CONFIG_SYS_RAMBOOT */
-
-#define CONFIG_SYS_BR4_PRELIM  ((RTC_BASE_ADDR & BRx_BA_MSK)   |\
-			 BRx_PS_8                       |\
-			 BRx_MS_UPMA                    |\
-			 BRx_V)
-
-#define CONFIG_SYS_OR4_PRELIM  (ORxU_AM_MSK | ORxU_BI)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_I82365
-
-#define CONFIG_SYS_PCMCIA_MEM_ADDR	0x81000000
-#define CONFIG_SYS_PCMCIA_MEM_SIZE	0x1000
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT	1	/* Use preinit IDE hook */
-#define CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card Adapter */
-
-#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE	 not supported	*/
-#undef	CONFIG_IDE_LED			/* LED	 for ide not supported	*/
-#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
-
-#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
-#define CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR	0xa0000000
-
-/* Offset for data I/O			*/
-#define CONFIG_SYS_ATA_DATA_OFFSET	0x100
-
-/* Offset for normal register accesses	*/
-#define CONFIG_SYS_ATA_REG_OFFSET	0x100
-
-/* Offset for alternate registers	*/
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x108
-
-#endif	/* __CONFIG_H */
diff --git a/include/pcmcia.h b/include/pcmcia.h
index 8e8831f..c8a730c 100644
--- a/include/pcmcia.h
+++ b/include/pcmcia.h
@@ -23,8 +23,6 @@
 
 #if defined(CONFIG_TQM8xxL)
 # define	CONFIG_PCMCIA_SLOT_B	/* The TQM8xxL use SLOT_B	*/
-#elif defined(CONFIG_ATC)		/* The ATC use SLOT_A	*/
-# define CONFIG_PCMCIA_SLOT_A
 #else
 # error "PCMCIA Slot not configured"
 #endif