global: Move remaining CONFIG_SYS_* to CFG_SYS_*

The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

1 files changed, 24 insertions, 24 deletions

diff --git a/include/configs/cobra5272.h b/include/configs/cobra5272.h
index 65b9074..01828ea 100644
--- a/include/configs/cobra5272.h
+++ b/include/configs/cobra5272.h
@@ -29,18 +29,18 @@
  * ---
  */
 
-#define CONFIG_SYS_CLK			66000000
+#define CFG_SYS_CLK			66000000
 #define CFG_SYS_SDRAM_SIZE		16		/* SDRAM size in MB */
 
 /* ---
  * Define baudrate for UART1 (console output, tftp, ...)
  * default value of CONFIG_BAUDRATE for Sentec board: 19200 baud
- * CONFIG_SYS_BAUDRATE_TABLE defines values that can be selected in u-boot command
+ * CFG_SYS_BAUDRATE_TABLE defines values that can be selected in u-boot command
  * interface
  * ---
  */
 
-#define CONFIG_SYS_UART_PORT		(0)
+#define CFG_SYS_UART_PORT		(0)
 
 /* ---
  * set "#if 0" to "#if 1" if (Hardware)-WATCHDOG should be enabled & change
@@ -133,21 +133,21 @@ enter a valid image address in flash */
  * ---
  */
 
-#define CONFIG_SYS_MBAR		0x10000000	/* Register Base Addrs */
+#define CFG_SYS_MBAR		0x10000000	/* Register Base Addrs */
 
 /* ---
  * System Conf. Reg. & System Protection Reg.
  * ---
  */
 
-#define CONFIG_SYS_SCR			0x0003
-#define CONFIG_SYS_SPR			0xffff
+#define CFG_SYS_SCR			0x0003
+#define CFG_SYS_SPR			0xffff
 
 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in internal SRAM)
  */
-#define CONFIG_SYS_INIT_RAM_ADDR	0x20000000
-#define CONFIG_SYS_INIT_RAM_SIZE	0x1000	/* Size of used area in internal SRAM	*/
+#define CFG_SYS_INIT_RAM_ADDR	0x20000000
+#define CFG_SYS_INIT_RAM_SIZE	0x1000	/* Size of used area in internal SRAM	*/
 
 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
@@ -168,28 +168,28 @@ enter a valid image address in flash */
  *-----------------------------------------------------------------------
  */
 
-#define CONFIG_SYS_FLASH_BASE		0xffe00000
+#define CFG_SYS_FLASH_BASE		0xffe00000
 
 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization ??
  */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+#define CFG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 
 /*-----------------------------------------------------------------------
  * Cache Configuration
  */
 
-#define ICACHE_STATUS			(CONFIG_SYS_INIT_RAM_ADDR + \
-					 CONFIG_SYS_INIT_RAM_SIZE - 8)
-#define DCACHE_STATUS			(CONFIG_SYS_INIT_RAM_ADDR + \
-					 CONFIG_SYS_INIT_RAM_SIZE - 4)
-#define CONFIG_SYS_ICACHE_INV		(CF_CACR_CINV | CF_CACR_INVI)
-#define CONFIG_SYS_CACHE_ACR0		(CFG_SYS_SDRAM_BASE | \
+#define ICACHE_STATUS			(CFG_SYS_INIT_RAM_ADDR + \
+					 CFG_SYS_INIT_RAM_SIZE - 8)
+#define DCACHE_STATUS			(CFG_SYS_INIT_RAM_ADDR + \
+					 CFG_SYS_INIT_RAM_SIZE - 4)
+#define CFG_SYS_ICACHE_INV		(CF_CACR_CINV | CF_CACR_INVI)
+#define CFG_SYS_CACHE_ACR0		(CFG_SYS_SDRAM_BASE | \
 					 CF_ADDRMASK(CFG_SYS_SDRAM_SIZE) | \
 					 CF_ACR_EN | CF_ACR_SM_ALL)
-#define CONFIG_SYS_CACHE_ICACR		(CF_CACR_CENB | CF_CACR_CINV | \
+#define CFG_SYS_CACHE_ICACR		(CF_CACR_CENB | CF_CACR_CINV | \
 					 CF_CACR_DISD | CF_CACR_INVI | \
 					 CF_CACR_CEIB | CF_CACR_DCM | \
 					 CF_CACR_EUSP)
@@ -209,15 +209,15 @@ enter a valid image address in flash */
 /*-----------------------------------------------------------------------
  * Port configuration (GPIO)
  */
-#define CONFIG_SYS_PACNT		0x00000000		/* PortA control reg.: All pins are external
+#define CFG_SYS_PACNT		0x00000000		/* PortA control reg.: All pins are external
 GPIO*/
-#define CONFIG_SYS_PADDR		0x00FF			/* PortA direction reg.: PA7 to PA0 are outputs
+#define CFG_SYS_PADDR		0x00FF			/* PortA direction reg.: PA7 to PA0 are outputs
 (1^=output, 0^=input) */
-#define CONFIG_SYS_PADAT		LED_STAT_0		/* PortA value reg.: Turn all LED off */
-#define CONFIG_SYS_PBCNT		0x55554155		/* PortB control reg.: Ethernet/UART
+#define CFG_SYS_PADAT		LED_STAT_0		/* PortA value reg.: Turn all LED off */
+#define CFG_SYS_PBCNT		0x55554155		/* PortB control reg.: Ethernet/UART
 configuration */
-#define CONFIG_SYS_PBDDR		0x0000			/* PortB direction: All pins configured as inputs */
-#define CONFIG_SYS_PBDAT		0x0000			/* PortB value reg. */
-#define CONFIG_SYS_PDCNT		0x00000000		/* PortD control reg. */
+#define CFG_SYS_PBDDR		0x0000			/* PortB direction: All pins configured as inputs */
+#define CFG_SYS_PBDAT		0x0000			/* PortB value reg. */
+#define CFG_SYS_PDCNT		0x00000000		/* PortD control reg. */
 
 #endif	/* _CONFIG_COBRA5272_H */