aboutsummaryrefslogtreecommitdiff
path: root/board
diff options
context:
space:
mode:
authorFabio Estevam <fabio.estevam@freescale.com>2015-05-04 11:22:55 -0300
committerStefano Babic <sbabic@denx.de>2015-05-15 19:20:47 +0200
commit712be3eef69a2b0205d3b87fb5ab5632e36722d7 (patch)
treea10da0fbaffce7a5e7017151b3464bd151237fb5 /board
parentd0285e0797894f5c754037a5b1ca97ceff486256 (diff)
downloadu-boot-712be3eef69a2b0205d3b87fb5ab5632e36722d7.zip
u-boot-712be3eef69a2b0205d3b87fb5ab5632e36722d7.tar.gz
u-boot-712be3eef69a2b0205d3b87fb5ab5632e36722d7.tar.bz2
mx6cuboxi: Fix Ethernet PHY detection problem
mx6cuboxi sometimes fails to recognize the Ethernet PHY: Net: Phy 0 not found The explanation for this behavior comes from from Rabeeh Khoury: "The LED_ACT pin on the carrier-one boards had a pull down that forces the phy address to 0x0; where on CuBox-i and the production HummingBoard that pin is connected directly to LED that depending on the pull down strength of the LED it might be sampled as '0' or '1' thus the phy address might appear as either address 0x0 or 0x4." "This is AR8035 implementation; in reset stage the LED pin is configured as input, and pull up/down does matter. In this case it configures the PHY address. After reset is deasserted the same LED pin becomes output and then according to the previous pull/up it should be active high/low" One way to properly fix this behavior is to place external pull-up/down resistors in the LED line, but from a software standpoint we can fix it by telling phy_find_by_mask() to scan the PHY at addresses 0x0 and 0x4. Reported-by: Vagrant Cascadian <vagrant@aikidev.net> Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com> Tested-By: Vagrant Cascadian <vagrant@aikidev.net>
Diffstat (limited to 'board')
-rw-r--r--board/solidrun/mx6cuboxi/mx6cuboxi.c29
1 files changed, 28 insertions, 1 deletions
diff --git a/board/solidrun/mx6cuboxi/mx6cuboxi.c b/board/solidrun/mx6cuboxi/mx6cuboxi.c
index 9aa0259..e83d2fe 100644
--- a/board/solidrun/mx6cuboxi/mx6cuboxi.c
+++ b/board/solidrun/mx6cuboxi/mx6cuboxi.c
@@ -25,6 +25,7 @@
#include <asm/imx-common/video.h>
#include <mmc.h>
#include <fsl_esdhc.h>
+#include <malloc.h>
#include <miiphy.h>
#include <netdev.h>
#include <asm/arch/crm_regs.h>
@@ -152,9 +153,14 @@ int board_phy_config(struct phy_device *phydev)
return 0;
}
+/* On Cuboxi Ethernet PHY can be located at addresses 0x0 or 0x4 */
+#define ETH_PHY_MASK ((1 << 0x0) | (1 << 0x4))
+
int board_eth_init(bd_t *bis)
{
struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
+ struct mii_dev *bus;
+ struct phy_device *phydev;
int ret = enable_fec_anatop_clock(ENET_25MHZ);
if (ret)
@@ -165,7 +171,28 @@ int board_eth_init(bd_t *bis)
setup_iomux_enet();
- return cpu_eth_init(bis);
+ bus = fec_get_miibus(IMX_FEC_BASE, -1);
+ if (!bus)
+ return -EINVAL;
+
+ phydev = phy_find_by_mask(bus, ETH_PHY_MASK, PHY_INTERFACE_MODE_RGMII);
+ if (!phydev) {
+ ret = -EINVAL;
+ goto free_bus;
+ }
+
+ debug("using phy at address %d\n", phydev->addr);
+ ret = fec_probe(bis, -1, IMX_FEC_BASE, bus, phydev);
+ if (ret)
+ goto free_phydev;
+
+ return 0;
+
+free_phydev:
+ free(phydev);
+free_bus:
+ free(bus);
+ return ret;
}
#ifdef CONFIG_VIDEO_IPUV3