arm: Remove mx25pdk board

This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>

5 files changed, 0 insertions, 291 deletions

diff --git a/board/freescale/mx25pdk/Kconfig b/board/freescale/mx25pdk/Kconfig
deleted file mode 100644
index af06b4c..0000000
--- a/board/freescale/mx25pdk/Kconfig
+++ /dev/null
@@ -1,15 +0,0 @@
-if TARGET_MX25PDK
-
-config SYS_BOARD
-	default "mx25pdk"
-
-config SYS_VENDOR
-	default "freescale"
-
-config SYS_SOC
-	default "mx25"
-
-config SYS_CONFIG_NAME
-	default "mx25pdk"
-
-endif
diff --git a/board/freescale/mx25pdk/MAINTAINERS b/board/freescale/mx25pdk/MAINTAINERS
deleted file mode 100644
index fa4651e..0000000
--- a/board/freescale/mx25pdk/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-MX25PDK BOARD
-M:	Fabio Estevam <fabio.estevam@nxp.com>
-S:	Maintained
-F:	board/freescale/mx25pdk/
-F:	include/configs/mx25pdk.h
-F:	configs/mx25pdk_defconfig
diff --git a/board/freescale/mx25pdk/Makefile b/board/freescale/mx25pdk/Makefile
deleted file mode 100644
index d3697d3..0000000
--- a/board/freescale/mx25pdk/Makefile
+++ /dev/null
@@ -1,7 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright (C) 2007, Guennadi Liakhovetski <lg@denx.de>
-#
-# (C) Copyright 2011 Freescale Semiconductor, Inc.
-
-obj-y	:= mx25pdk.o
diff --git a/board/freescale/mx25pdk/imximage.cfg b/board/freescale/mx25pdk/imximage.cfg
deleted file mode 100644
index 762ccd0..0000000
--- a/board/freescale/mx25pdk/imximage.cfg
+++ /dev/null
@@ -1,64 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2009
- * Stefano Babic DENX Software Engineering sbabic@denx.de.
- *
- * Refer doc/imx/mkimage/imximage.txt for more details about how-to configure
- * and create imximage boot image
- *
- * The syntax is taken as close as possible with the kwbimage
- */
-
-/*
- * Boot Device : one of
- * spi, sd (the board has no nand neither onenand)
- */
-BOOT_FROM	sd
-
-/*
- * Device Configuration Data (DCD)
- *
- * Each entry must have the format:
- * Addr-type           Address        Value
- *
- * where:
- *	Addr-type register length (1,2 or 4 bytes)
- *	Address	  absolute address of the register
- *	value	  value to be stored in the register
- */
-/* EIM config-CS5 init -- CPLD */
-DATA 4 0xB8002050 0x0000D843
-DATA 4 0xB8002054 0x22252521
-DATA 4 0xB8002058 0x22220A00
-
-/* DDR2 init */
-DATA 4 0xB8001004 0x0076E83A
-DATA 4 0xB8001010 0x00000204
-DATA 4 0xB8001000 0x92210000
-DATA 4 0x80000f00 0x12344321
-DATA 4 0xB8001000 0xB2210000
-DATA 1 0x82000000 0xda
-DATA 1 0x83000000 0xda
-DATA 1 0x81000400 0xda
-DATA 1 0x80000333 0xda
-
-DATA 4 0xB8001000 0x92210000
-DATA 1 0x80000400 0x12345678
-
-DATA 4 0xB8001000 0xA2210000
-DATA 4 0x80000000 0x87654321
-DATA 4 0x80000000 0x87654321
-
-DATA 4 0xB8001000 0xB2210000
-DATA 1 0x80000233 0xda
-DATA 1 0x81000780 0xda
-DATA 1 0x81000400 0xda
-DATA 4 0xB8001000 0x82216080
-DATA 4 0x43FAC454 0x00001000
-
-DATA 4 0x53F80008 0x20034000
-
-/* Enable the clocks */
-DATA 4 0x53f8000c 0x1fffffff
-DATA 4 0x53f80010 0xffffffff
-DATA 4 0x53f80014 0xfdfff
diff --git a/board/freescale/mx25pdk/mx25pdk.c b/board/freescale/mx25pdk/mx25pdk.c
deleted file mode 100644
index 3b445a4..0000000
--- a/board/freescale/mx25pdk/mx25pdk.c
+++ /dev/null
@@ -1,199 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2011 Freescale Semiconductor, Inc.
- *
- * Author: Fabio Estevam <fabio.estevam@freescale.com>
- */
-
-#include <common.h>
-#include <init.h>
-#include <asm/global_data.h>
-#include <asm/io.h>
-#include <asm/gpio.h>
-#include <asm/arch/imx-regs.h>
-#include <asm/arch/iomux-mx25.h>
-#include <asm/arch/clock.h>
-#include <mmc.h>
-#include <fsl_esdhc_imx.h>
-#include <i2c.h>
-#include <linux/delay.h>
-#include <power/pmic.h>
-#include <fsl_pmic.h>
-#include <mc34704.h>
-
-#define FEC_RESET_B		IMX_GPIO_NR(4, 8)
-#define FEC_ENABLE_B		IMX_GPIO_NR(2, 3)
-#define CARD_DETECT		IMX_GPIO_NR(2, 1)
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#ifdef CONFIG_FSL_ESDHC_IMX
-struct fsl_esdhc_cfg esdhc_cfg[1] = {
-	{IMX_MMC_SDHC1_BASE},
-};
-#endif
-
-/*
- * FIXME: need to revisit this
- * The original code enabled PUE and 100-k pull-down without PKE, so the right
- * value here is likely:
- *	0 for no pull
- * or:
- *	PAD_CTL_PUS_100K_DOWN for 100-k pull-down
- */
-#define FEC_OUT_PAD_CTRL	0
-
-#define I2C_PAD_CTRL		(PAD_CTL_HYS | PAD_CTL_PUS_100K_UP | \
-				 PAD_CTL_ODE)
-
-static void mx25pdk_fec_init(void)
-{
-	static const iomux_v3_cfg_t fec_pads[] = {
-		MX25_PAD_FEC_TX_CLK__FEC_TX_CLK,
-		MX25_PAD_FEC_RX_DV__FEC_RX_DV,
-		MX25_PAD_FEC_RDATA0__FEC_RDATA0,
-		NEW_PAD_CTRL(MX25_PAD_FEC_TDATA0__FEC_TDATA0, FEC_OUT_PAD_CTRL),
-		NEW_PAD_CTRL(MX25_PAD_FEC_TX_EN__FEC_TX_EN, FEC_OUT_PAD_CTRL),
-		NEW_PAD_CTRL(MX25_PAD_FEC_MDC__FEC_MDC, FEC_OUT_PAD_CTRL),
-		MX25_PAD_FEC_MDIO__FEC_MDIO,
-		MX25_PAD_FEC_RDATA1__FEC_RDATA1,
-		NEW_PAD_CTRL(MX25_PAD_FEC_TDATA1__FEC_TDATA1, FEC_OUT_PAD_CTRL),
-
-		NEW_PAD_CTRL(MX25_PAD_D12__GPIO_4_8, 0), /* FEC_RESET_B */
-		NEW_PAD_CTRL(MX25_PAD_A17__GPIO_2_3, 0), /* FEC_ENABLE_B */
-	};
-
-	static const iomux_v3_cfg_t i2c_pads[] = {
-		NEW_PAD_CTRL(MX25_PAD_I2C1_CLK__I2C1_CLK, I2C_PAD_CTRL),
-		NEW_PAD_CTRL(MX25_PAD_I2C1_DAT__I2C1_DAT, I2C_PAD_CTRL),
-	};
-
-	imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));
-
-	/* Assert RESET and ENABLE low */
-	gpio_direction_output(FEC_RESET_B, 0);
-	gpio_direction_output(FEC_ENABLE_B, 0);
-
-	udelay(10);
-
-	/* Deassert RESET and ENABLE */
-	gpio_set_value(FEC_RESET_B, 1);
-	gpio_set_value(FEC_ENABLE_B, 1);
-
-	/* Setup I2C pins so that PMIC can turn on PHY supply */
-	imx_iomux_v3_setup_multiple_pads(i2c_pads, ARRAY_SIZE(i2c_pads));
-}
-
-int dram_init(void)
-{
-	/* dram_init must store complete ramsize in gd->ram_size */
-	gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
-				PHYS_SDRAM_1_SIZE);
-	return 0;
-}
-
-/*
- * Set up input pins with hysteresis and 100-k pull-ups
- */
-#define UART1_IN_PAD_CTRL	(PAD_CTL_HYS | PAD_CTL_PUS_100K_UP)
-/*
- * FIXME: need to revisit this
- * The original code enabled PUE and 100-k pull-down without PKE, so the right
- * value here is likely:
- *	0 for no pull
- * or:
- *	PAD_CTL_PUS_100K_DOWN for 100-k pull-down
- */
-#define UART1_OUT_PAD_CTRL	0
-
-static void mx25pdk_uart1_init(void)
-{
-	static const iomux_v3_cfg_t uart1_pads[] = {
-		NEW_PAD_CTRL(MX25_PAD_UART1_RXD__UART1_RXD, UART1_IN_PAD_CTRL),
-		NEW_PAD_CTRL(MX25_PAD_UART1_TXD__UART1_TXD, UART1_OUT_PAD_CTRL),
-		NEW_PAD_CTRL(MX25_PAD_UART1_RTS__UART1_RTS, UART1_OUT_PAD_CTRL),
-		NEW_PAD_CTRL(MX25_PAD_UART1_CTS__UART1_CTS, UART1_IN_PAD_CTRL),
-	};
-
-	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
-}
-
-int board_early_init_f(void)
-{
-	mx25pdk_uart1_init();
-
-	return 0;
-}
-
-int board_init(void)
-{
-	/* address of boot parameters */
-	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
-
-	return 0;
-}
-
-int board_late_init(void)
-{
-	struct pmic *p;
-	int ret;
-
-	mx25pdk_fec_init();
-
-	ret = pmic_init(I2C_0);
-	if (ret)
-		return ret;
-
-	p = pmic_get("FSL_PMIC");
-	if (!p)
-		return -ENODEV;
-
-	/* Turn on Ethernet PHY and LCD supplies */
-	pmic_reg_write(p, MC34704_GENERAL2_REG, ONOFFE | ONOFFA);
-
-	return 0;
-}
-
-#ifdef CONFIG_FSL_ESDHC_IMX
-int board_mmc_getcd(struct mmc *mmc)
-{
-	/* Set up the Card Detect pin. */
-	imx_iomux_v3_setup_pad(NEW_PAD_CTRL(MX25_PAD_A15__GPIO_2_1, 0));
-
-	gpio_direction_input(CARD_DETECT);
-	return !gpio_get_value(CARD_DETECT);
-}
-
-int board_mmc_init(struct bd_info *bis)
-{
-	static const iomux_v3_cfg_t sdhc1_pads[] = {
-		NEW_PAD_CTRL(MX25_PAD_SD1_CMD__SD1_CMD, NO_PAD_CTRL),
-		NEW_PAD_CTRL(MX25_PAD_SD1_CLK__SD1_CLK, NO_PAD_CTRL),
-		NEW_PAD_CTRL(MX25_PAD_SD1_DATA0__SD1_DATA0, NO_PAD_CTRL),
-		NEW_PAD_CTRL(MX25_PAD_SD1_DATA1__SD1_DATA1, NO_PAD_CTRL),
-		NEW_PAD_CTRL(MX25_PAD_SD1_DATA2__SD1_DATA2, NO_PAD_CTRL),
-		NEW_PAD_CTRL(MX25_PAD_SD1_DATA3__SD1_DATA3, NO_PAD_CTRL),
-	};
-
-	imx_iomux_v3_setup_multiple_pads(sdhc1_pads, ARRAY_SIZE(sdhc1_pads));
-
-	/*
-	 * Set the eSDHC1 PER clock to the maximum frequency lower than or equal
-	 * to 50 MHz that can be obtained, which requires to use UPLL as the
-	 * clock source. This actually gives 48 MHz.
-	 */
-	imx_set_perclk(MXC_ESDHC1_CLK, true, 50000000);
-	esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC1_CLK);
-	return fsl_esdhc_initialize(bis, &esdhc_cfg[0]);
-}
-#endif
-
-int checkboard(void)
-{
-	puts("Board: MX25PDK\n");
-
-	return 0;
-}
-
-/* Lowlevel init isn't used on mx25pdk, so just provide a dummy one here */
-void lowlevel_init(void) {}