Merge tag 'xilinx-for-v2020.04' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze

Xilinx/FPGA changes for v2020.04

ARM64:
- Add INIT_SPL_RELATIVE dependency

SPL:
- FIT image fix
- Enable customization of bl2_plat_get_bl31_params()

Pytest:
- Add test for octal/hex conversions

Microblaze:
- Fix manual relocation for one SPI instance

Nand:
- Convert zynq/zynqmp drivers to DM

Xilinx:
- Enable boot script location via Kconfig
- Support OF_SEPARATE in board FDT selection
- Remove low level uart setup it is done later by code
- Add support for DEVICE_TREE variable passing for SPL

Zynq:
- Enable jtag boot mode via distro boot
- Removing unused baseaddresses from hardware.h
- DT fixups

ZynqMP:
- Fix emmc boot sequence
- Simplify spl logic around bss and board_init_r()
- Support psu_post_config_data() calling
- Tune mini-nand DTS
- Fix psu wiring for a2197 boards
- Add runtime MMC device boot order filling in spl
- Clear ATF handoff handling with custom bl2_plat_get_bl31_params()
- Add support u-boot.its generation
- Use single image configuration for all platforms
- Enable PANIC_HANG via Kconfig
- DT fixups
- Firmware fixes
- Add support for zcu208 and zcu1285

Versal:
- Fix emmc boot sequence
- Enable board_late_init() by default

16 files changed, 1023 insertions, 87 deletions

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index adb843c..04a8ccc 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -282,6 +282,8 @@ dtb-$(CONFIG_ARCH_ZYNQMP) += \
 	zynqmp-zcu111-revA.dtb			\
 	zynqmp-zcu1275-revA.dtb			\
 	zynqmp-zcu1275-revB.dtb			\
+	zynqmp-zcu1285-revA.dtb			\
+	zynqmp-zcu208-revA.dtb			\
 	zynqmp-zcu216-revA.dtb			\
 	zynqmp-zc1232-revA.dtb			\
 	zynqmp-zc1254-revA.dtb			\
diff --git a/arch/arm/dts/zynq-7000.dtsi b/arch/arm/dts/zynq-7000.dtsi
index 07dfa0d..c35eb23 100644
--- a/arch/arm/dts/zynq-7000.dtsi
+++ b/arch/arm/dts/zynq-7000.dtsi
@@ -62,6 +62,39 @@
 		regulator-always-on;
 	};
 
+	replicator {
+		compatible = "arm,coresight-static-replicator";
+		clocks = <&clkc 27>, <&clkc 46>, <&clkc 47>;
+		clock-names = "apb_pclk", "dbg_trc", "dbg_apb";
+
+		out-ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			/* replicator output ports */
+			port@0 {
+				reg = <0>;
+				replicator_out_port0: endpoint {
+					remote-endpoint = <&tpiu_in_port>;
+				};
+			};
+			port@1 {
+				reg = <1>;
+				replicator_out_port1: endpoint {
+					remote-endpoint = <&etb_in_port>;
+				};
+			};
+		};
+		in-ports {
+			/* replicator input port */
+			port {
+				replicator_in_port0: endpoint {
+					remote-endpoint = <&funnel_out_port>;
+				};
+			};
+		};
+	};
+
 	amba: amba {
 		u-boot,dm-pre-reloc;
 		compatible = "simple-bus";
@@ -415,5 +448,107 @@
 			reg = <0xf8005000 0x1000>;
 			timeout-sec = <10>;
 		};
+
+		etb@f8801000 {
+			compatible = "arm,coresight-etb10", "arm,primecell";
+			reg = <0xf8801000 0x1000>;
+			clocks = <&clkc 27>, <&clkc 46>, <&clkc 47>;
+			clock-names = "apb_pclk", "dbg_trc", "dbg_apb";
+			in-ports {
+				port {
+					etb_in_port: endpoint {
+						remote-endpoint = <&replicator_out_port1>;
+					};
+				};
+			};
+		};
+
+		tpiu@f8803000 {
+			compatible = "arm,coresight-tpiu", "arm,primecell";
+			reg = <0xf8803000 0x1000>;
+			clocks = <&clkc 27>, <&clkc 46>, <&clkc 47>;
+			clock-names = "apb_pclk", "dbg_trc", "dbg_apb";
+			in-ports {
+				port {
+					tpiu_in_port: endpoint {
+						remote-endpoint = <&replicator_out_port0>;
+					};
+				};
+			};
+		};
+
+		funnel@f8804000 {
+			compatible = "arm,coresight-static-funnel", "arm,primecell";
+			reg = <0xf8804000 0x1000>;
+			clocks = <&clkc 27>, <&clkc 46>, <&clkc 47>;
+			clock-names = "apb_pclk", "dbg_trc", "dbg_apb";
+
+			/* funnel output ports */
+			out-ports {
+				port {
+					funnel_out_port: endpoint {
+						remote-endpoint =
+							<&replicator_in_port0>;
+					};
+				};
+			};
+
+			in-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				/* funnel input ports */
+				port@0 {
+					reg = <0>;
+					funnel0_in_port0: endpoint {
+						remote-endpoint = <&ptm0_out_port>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					funnel0_in_port1: endpoint {
+						remote-endpoint = <&ptm1_out_port>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+					funnel0_in_port2: endpoint {
+					};
+				};
+				/* The other input ports are not connect to anything */
+			};
+		};
+
+		ptm@f889c000 {
+			compatible = "arm,coresight-etm3x", "arm,primecell";
+			reg = <0xf889c000 0x1000>;
+			clocks = <&clkc 27>, <&clkc 46>, <&clkc 47>;
+			clock-names = "apb_pclk", "dbg_trc", "dbg_apb";
+			cpu = <&cpu0>;
+			out-ports {
+				port {
+					ptm0_out_port: endpoint {
+						remote-endpoint = <&funnel0_in_port0>;
+					};
+				};
+			};
+		};
+
+		ptm@f889d000 {
+			compatible = "arm,coresight-etm3x", "arm,primecell";
+			reg = <0xf889d000 0x1000>;
+			clocks = <&clkc 27>, <&clkc 46>, <&clkc 47>;
+			clock-names = "apb_pclk", "dbg_trc", "dbg_apb";
+			cpu = <&cpu1>;
+			out-ports {
+				port {
+					ptm1_out_port: endpoint {
+						remote-endpoint = <&funnel0_in_port1>;
+					};
+				};
+			};
+		};
 	};
 };
diff --git a/arch/arm/dts/zynq-zc770-xm011.dts b/arch/arm/dts/zynq-zc770-xm011.dts
index 1123bfc..6148201 100644
--- a/arch/arm/dts/zynq-zc770-xm011.dts
+++ b/arch/arm/dts/zynq-zc770-xm011.dts
@@ -47,6 +47,14 @@
 	};
 };
 
+&nand0 {
+	status = "okay";
+};
+
+&smcc {
+	status = "okay";
+};
+
 &spi0 {
 	status = "okay";
 	num-cs = <4>;
diff --git a/arch/arm/dts/zynqmp-clk-ccf.dtsi b/arch/arm/dts/zynqmp-clk-ccf.dtsi
index 998298c..8eacd22 100644
--- a/arch/arm/dts/zynqmp-clk-ccf.dtsi
+++ b/arch/arm/dts/zynqmp-clk-ccf.dtsi
@@ -2,7 +2,7 @@
 /*
  * Clock specification for Xilinx ZynqMP
  *
- * (C) Copyright 2017, Xilinx, Inc.
+ * (C) Copyright 2017 - 2019, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  */
@@ -173,26 +173,30 @@
 };
 
 &gem0 {
-	clocks = <&zynqmp_clk LPD_LSBUS>, <&zynqmp_clk GEM0_REF>, <&zynqmp_clk GEM0_TX>,
-		 <&zynqmp_clk GEM0_RX>, <&zynqmp_clk GEM_TSU>;
+	clocks = <&zynqmp_clk LPD_LSBUS>, <&zynqmp_clk GEM0_REF>,
+		 <&zynqmp_clk GEM0_TX>, <&zynqmp_clk GEM0_RX>,
+		 <&zynqmp_clk GEM_TSU>;
 	clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk";
 };
 
 &gem1 {
-	clocks = <&zynqmp_clk LPD_LSBUS>, <&zynqmp_clk GEM1_REF>, <&zynqmp_clk GEM1_TX>,
-		 <&zynqmp_clk GEM1_RX>, <&zynqmp_clk GEM_TSU>;
+	clocks = <&zynqmp_clk LPD_LSBUS>, <&zynqmp_clk GEM1_REF>,
+		 <&zynqmp_clk GEM1_TX>, <&zynqmp_clk GEM1_RX>,
+		 <&zynqmp_clk GEM_TSU>;
 	clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk";
 };
 
 &gem2 {
-	clocks = <&zynqmp_clk LPD_LSBUS>, <&zynqmp_clk GEM2_REF>, <&zynqmp_clk GEM2_TX>,
-		 <&zynqmp_clk GEM2_RX>, <&zynqmp_clk GEM_TSU>;
+	clocks = <&zynqmp_clk LPD_LSBUS>, <&zynqmp_clk GEM2_REF>,
+		 <&zynqmp_clk GEM2_TX>, <&zynqmp_clk GEM2_RX>,
+		 <&zynqmp_clk GEM_TSU>;
 	clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk";
 };
 
 &gem3 {
-	clocks = <&zynqmp_clk LPD_LSBUS>, <&zynqmp_clk GEM3_REF>, <&zynqmp_clk GEM3_TX>,
-		 <&zynqmp_clk GEM3_RX>, <&zynqmp_clk GEM_TSU>;
+	clocks = <&zynqmp_clk LPD_LSBUS>, <&zynqmp_clk GEM3_REF>,
+		 <&zynqmp_clk GEM3_TX>, <&zynqmp_clk GEM3_RX>,
+		 <&zynqmp_clk GEM_TSU>;
 	clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk";
 };
 
diff --git a/arch/arm/dts/zynqmp-clk.dtsi b/arch/arm/dts/zynqmp-clk.dtsi
index 9ef55ad..c9464ec 100644
--- a/arch/arm/dts/zynqmp-clk.dtsi
+++ b/arch/arm/dts/zynqmp-clk.dtsi
@@ -61,13 +61,13 @@
 		clock-accuracy = <100>;
 	};
 
-	dpdma_clk: dpdma_clk {
+	dpdma_clk: dpdma-clk {
 		compatible = "fixed-clock";
 		#clock-cells = <0x0>;
 		clock-frequency = <533000000>;
 	};
 
-	drm_clock: drm_clock {
+	drm_clock: drm-clock {
 		compatible = "fixed-clock";
 		#clock-cells = <0x0>;
 		clock-frequency = <262750000>;
diff --git a/arch/arm/dts/zynqmp-mini-nand.dts b/arch/arm/dts/zynqmp-mini-nand.dts
index 93aa193..d376ade 100644
--- a/arch/arm/dts/zynqmp-mini-nand.dts
+++ b/arch/arm/dts/zynqmp-mini-nand.dts
@@ -50,55 +50,6 @@
 			#size-cells = <1>;
 			arasan,has-mdma;
 			num-cs = <2>;
-
-			partition@0 {	/* for testing purpose */
-				label = "nand-fsbl-uboot";
-				reg = <0x0 0x0 0x400000>;
-			};
-			partition@1 {	/* for testing purpose */
-				label = "nand-linux";
-				reg = <0x0 0x400000 0x1400000>;
-			};
-			partition@2 {	/* for testing purpose */
-				label = "nand-device-tree";
-				reg = <0x0 0x1800000 0x400000>;
-			};
-			partition@3 {	/* for testing purpose */
-				label = "nand-rootfs";
-				reg = <0x0 0x1C00000 0x1400000>;
-			};
-			partition@4 {	/* for testing purpose */
-				label = "nand-bitstream";
-				reg = <0x0 0x3000000 0x400000>;
-			};
-			partition@5 {	/* for testing purpose */
-				label = "nand-misc";
-				reg = <0x0 0x3400000 0xFCC00000>;
-			};
-			partition@6 {	/* for testing purpose */
-				label = "nand1-fsbl-uboot";
-				reg = <0x1 0x0 0x400000>;
-			};
-			partition@7 {	/* for testing purpose */
-				label = "nand1-linux";
-				reg = <0x1 0x400000 0x1400000>;
-			};
-			partition@8 {	/* for testing purpose */
-				label = "nand1-device-tree";
-				reg = <0x1 0x1800000 0x400000>;
-			};
-			partition@9 {	/* for testing purpose */
-				label = "nand1-rootfs";
-				reg = <0x1 0x1C00000 0x1400000>;
-			};
-			partition@10 {	/* for testing purpose */
-				label = "nand1-bitstream";
-				reg = <0x1 0x3000000 0x400000>;
-			};
-			partition@11 {	/* for testing purpose */
-				label = "nand1-misc";
-				reg = <0x1 0x3400000 0xFCC00000>;
-			};
 		};
 	};
 };
diff --git a/arch/arm/dts/zynqmp-zcu100-revC.dts b/arch/arm/dts/zynqmp-zcu100-revC.dts
index 14aa98d..21118c8 100644
--- a/arch/arm/dts/zynqmp-zcu100-revC.dts
+++ b/arch/arm/dts/zynqmp-zcu100-revC.dts
@@ -11,7 +11,7 @@
 /dts-v1/;
 
 #include "zynqmp.dtsi"
-#include "zynqmp-clk.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
@@ -53,7 +53,7 @@
 			label = "sw4";
 			gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
-			gpio-key,wakeup;
+			wakeup-source;
 			autorepeat;
 		};
 	};
@@ -95,7 +95,7 @@
 			linux,default-trigger = "bluetooth-power";
 		};
 
-		vbus_det { /* U5 USB5744 VBUS detection via MIO25 */
+		vbus-det { /* U5 USB5744 VBUS detection via MIO25 */
 			label = "vbus_det";
 			gpios = <&gpio 25 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
@@ -120,9 +120,10 @@
 		regulator-boot-on;
 	};
 
-	sdio_pwrseq: sdio_pwrseq {
+	sdio_pwrseq: sdio-pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&gpio 7 GPIO_ACTIVE_LOW>; /* WIFI_EN */
+		post-power-on-delay-ms = <10>;
 	};
 
 	ina226 {
diff --git a/arch/arm/dts/zynqmp-zcu102-revA.dts b/arch/arm/dts/zynqmp-zcu102-revA.dts
index 78110c4..b580f92 100644
--- a/arch/arm/dts/zynqmp-zcu102-revA.dts
+++ b/arch/arm/dts/zynqmp-zcu102-revA.dts
@@ -51,14 +51,14 @@
 			label = "sw19";
 			gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_DOWN>;
-			gpio-key,wakeup;
+			wakeup-source;
 			autorepeat;
 		};
 	};
 
 	leds {
 		compatible = "gpio-leds";
-		heartbeat_led {
+		heartbeat-led {
 			label = "heartbeat";
 			gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
@@ -213,25 +213,25 @@
 		gpio-line-names = "PS_GTR_LAN_SEL0", "PS_GTR_LAN_SEL1", "PS_GTR_LAN_SEL2", "PS_GTR_LAN_SEL3",
 				"PCI_CLK_DIR_SEL", "IIC_MUX_RESET_B", "GEM3_EXP_RESET_B",
 				"", "", "", "", "", "", "", "", "";
-		gtr_sel0 {
+		gtr-sel0 {
 			gpio-hog;
 			gpios = <0 0>;
 			output-low; /* PCIE = 0, DP = 1 */
 			line-name = "sel0";
 		};
-		gtr_sel1 {
+		gtr-sel1 {
 			gpio-hog;
 			gpios = <1 0>;
 			output-high; /* PCIE = 0, DP = 1 */
 			line-name = "sel1";
 		};
-		gtr_sel2 {
+		gtr-sel2 {
 			gpio-hog;
 			gpios = <2 0>;
 			output-high; /* PCIE = 0, USB0 = 1 */
 			line-name = "sel2";
 		};
-		gtr_sel3 {
+		gtr-sel3 {
 			gpio-hog;
 			gpios = <3 0>;
 			output-high; /* PCIE = 0, SATA = 1 */
diff --git a/arch/arm/dts/zynqmp-zcu102-revB.dts b/arch/arm/dts/zynqmp-zcu102-revB.dts
index 2132024..38ec188 100644
--- a/arch/arm/dts/zynqmp-zcu102-revB.dts
+++ b/arch/arm/dts/zynqmp-zcu102-revB.dts
@@ -25,7 +25,7 @@
 		/* reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; */
 	};
 	/* Cleanup from RevA */
-	/delete-node/ phy@21;
+	/delete-node/ ethernet-phy@21;
 };
 
 /* Fix collision with u61 */
diff --git a/arch/arm/dts/zynqmp-zcu106-revA.dts b/arch/arm/dts/zynqmp-zcu106-revA.dts
index b4dd101..d31982f 100644
--- a/arch/arm/dts/zynqmp-zcu106-revA.dts
+++ b/arch/arm/dts/zynqmp-zcu106-revA.dts
@@ -51,14 +51,14 @@
 			label = "sw19";
 			gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_DOWN>;
-			gpio-key,wakeup;
+			wakeup-source;
 			autorepeat;
 		};
 	};
 
 	leds {
 		compatible = "gpio-leds";
-		heartbeat_led {
+		heartbeat-led {
 			label = "heartbeat";
 			gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
@@ -653,7 +653,6 @@
 /* SD1 with level shifter */
 &sdhci1 {
 	status = "okay";
-	no-1-8-v;
 	xlnx,mio_bank = <1>;
 };
 
diff --git a/arch/arm/dts/zynqmp-zcu111-revA.dts b/arch/arm/dts/zynqmp-zcu111-revA.dts
index aabf73d..bff224f 100644
--- a/arch/arm/dts/zynqmp-zcu111-revA.dts
+++ b/arch/arm/dts/zynqmp-zcu111-revA.dts
@@ -51,14 +51,14 @@
 			label = "sw19";
 			gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_DOWN>;
-			gpio-key,wakeup;
+			wakeup-source;
 			autorepeat;
 		};
 	};
 
 	leds {
 		compatible = "gpio-leds";
-		heartbeat_led {
+		heartbeat-led {
 			label = "heartbeat";
 			gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
@@ -566,7 +566,6 @@
 /* SD1 with level shifter */
 &sdhci1 {
 	status = "okay";
-	no-1-8-v;
 	disable-wp;
 	xlnx,mio_bank = <1>;
 };
diff --git a/arch/arm/dts/zynqmp-zcu1275-revB.dts b/arch/arm/dts/zynqmp-zcu1275-revB.dts
index 34c4bec..2ec29b0 100644
--- a/arch/arm/dts/zynqmp-zcu1275-revB.dts
+++ b/arch/arm/dts/zynqmp-zcu1275-revB.dts
@@ -75,6 +75,10 @@
 
 &sdhci1 {
 	status = "okay";
+	/*
+	 * 1.0 revision has level shifter and this property should be
+	 * removed for supporting UHS mode
+	 */
 	no-1-8-v;
 	xlnx,mio_bank = <1>;
 };
diff --git a/arch/arm/dts/zynqmp-zcu1285-revA.dts b/arch/arm/dts/zynqmp-zcu1285-revA.dts
new file mode 100644
index 0000000..9c18013
--- /dev/null
+++ b/arch/arm/dts/zynqmp-zcu1285-revA.dts
@@ -0,0 +1,245 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx ZynqMP ZCU1285 RevA
+ *
+ * (C) Copyright 2018 - 2019, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ * Siva Durga Prasad Paladugu <sivadur@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+
+/ {
+	model = "ZynqMP ZCU1285 RevA";
+	compatible = "xlnx,zynqmp-zcu1285-revA", "xlnx,zynqmp-zcu1285",
+		     "xlnx,zynqmp";
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &dcc;
+		spi0 = &qspi;
+		mmc0 = &sdhci1;
+		i2c = &i2c0; /* EMIO */
+	};
+
+	chosen {
+		bootargs = "earlycon";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+
+	ina226-u60 {
+		compatible = "iio-hwmon";
+		io-channels = <&u60 0>, <&u60 1>, <&u60 2>, <&u60 3>;
+	};
+	ina226-u61 {
+		compatible = "iio-hwmon";
+		io-channels = <&u61 0>, <&u61 1>, <&u61 2>, <&u61 3>;
+	};
+	ina226-u63 {
+		compatible = "iio-hwmon";
+		io-channels = <&u63 0>, <&u63 1>, <&u63 2>, <&u63 3>;
+	};
+	ina226-u65 {
+		compatible = "iio-hwmon";
+		io-channels = <&u65 0>, <&u65 1>, <&u65 2>, <&u65 3>;
+	};
+	ina226-u64 {
+		compatible = "iio-hwmon";
+		io-channels = <&u64 0>, <&u64 1>, <&u64 2>, <&u64 3>;
+	};
+};
+
+&dcc {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	i2c-mux@75 {
+		compatible = "nxp,pca9548"; /* u22 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x75>;
+
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/* PMBUS */
+			max20751@74 { /* u23 */
+				compatible = "maxim,max20751";
+				reg = <0x74>;
+			};
+			max20751@70 { /* u89 */
+				compatible = "maxim,max20751";
+				reg = <0x70>;
+			};
+			max15301@a { /* u28 */
+				compatible = "maxim,max15301";
+				reg = <0xa>;
+			};
+			max15303@b { /* u48 */
+				compatible = "maxim,max15303";
+				reg = <0xb>;
+			};
+			max15303@d { /* u27 */
+				compatible = "maxim,max15303";
+				reg = <0xd>;
+			};
+			max15303@e { /* u11 */
+				compatible = "maxim,max15303";
+				reg = <0xe>;
+			};
+			max15303@f { /* u96 */
+				compatible = "maxim,max15303";
+				reg = <0xf>;
+			};
+			max15303@11 { /* u47 */
+				compatible = "maxim,max15303";
+				reg = <0x11>;
+			};
+			max15303@12 { /* u24 */
+				compatible = "maxim,max15303";
+				reg = <0x12>;
+			};
+			max15301@13 { /* u29 */
+				compatible = "maxim,max15301";
+				reg = <0x13>;
+			};
+			max15303@14 { /* u51 */
+				compatible = "maxim,max15303";
+				reg = <0x14>;
+			};
+			max15303@15 { /* u30 */
+				compatible = "maxim,max15303";
+				reg = <0x15>;
+			};
+			max15303@16 { /* u102 */
+				compatible = "maxim,max15303";
+				reg = <0x16>;
+			};
+			max15301@17 { /* u50 */
+				compatible = "maxim,max15301";
+				reg = <0x17>;
+			};
+			max15301@18 { /* u31 */
+				compatible = "maxim,max15301";
+				reg = <0x18>;
+			};
+		};
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			/* CM_I2C */
+		};
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			/* SYS_EEPROM */
+			eeprom: eeprom@54 { /* u101 */
+				compatible = "atmel,24c32"; /* 24LC32A */
+				reg = <0x54>;
+			};
+		};
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			/* FMC1 */
+		};
+		i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			/* FMC2 */
+		};
+		i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+			/* ANALOG_PMBUS */
+			u60: ina226@40 { /* u60 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-u60";
+				reg = <0x40>;
+				shunt-resistor = <1000>;
+			};
+			u61: ina226@41 { /* u61 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-u61";
+				reg = <0x41>;
+				shunt-resistor = <1000>;
+			};
+			u63: ina226@42 { /* u63 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-u63";
+				reg = <0x42>;
+				shunt-resistor = <1000>;
+			};
+			u65: ina226@43 { /* u65 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-u65";
+				reg = <0x43>;
+				shunt-resistor = <1000>;
+			};
+			u64: ina226@44 { /* u64 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-u64";
+				reg = <0x44>;
+				shunt-resistor = <1000>;
+			};
+		};
+		i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+			/* ANALOG_CM_I2C */
+		};
+		i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+			/* FMC3 */
+		};
+	};
+};
+
+&qspi {
+	status = "okay";
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor"; /* 32MB */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <1>;
+		spi-max-frequency = <108000000>; /* Based on DC1 spec */
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&sdhci1 {
+	status = "okay";
+	xlnx,mio_bank = <1>;
+};
diff --git a/arch/arm/dts/zynqmp-zcu208-revA.dts b/arch/arm/dts/zynqmp-zcu208-revA.dts
new file mode 100644
index 0000000..9181060
--- /dev/null
+++ b/arch/arm/dts/zynqmp-zcu208-revA.dts
@@ -0,0 +1,588 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx ZynqMP ZCU208
+ *
+ * (C) Copyright 2017 - 2019, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/phy/phy.h>
+
+/ {
+	model = "ZynqMP ZCU208 RevA";
+	compatible = "xlnx,zynqmp-zcu208-revA", "xlnx,zynqmp-zcu208", "xlnx,zynqmp";
+
+	aliases {
+		ethernet0 = &gem3;
+		gpio0 = &gpio;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		mmc0 = &sdhci1;
+		rtc0 = &rtc;
+		serial0 = &uart0;
+		serial1 = &dcc;
+		spi0 = &qspi;
+		usb0 = &usb0;
+	};
+
+	chosen {
+		bootargs = "earlycon";
+		stdout-path = "serial0:115200n8";
+		xlnx,eeprom = &eeprom;
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+		sw19 {
+			label = "sw19";
+			gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
+			linux,code = <KEY_DOWN>;
+			gpio-key,wakeup;
+			autorepeat;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		heartbeat_led {
+			label = "heartbeat";
+			gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	ina226-vccint {
+		compatible = "iio-hwmon";
+		io-channels = <&vccint 0>, <&vccint 1>, <&vccint 2>, <&vccint 3>;
+	};
+	ina226-vccint-io-bram-ps {
+		compatible = "iio-hwmon";
+		io-channels = <&vccint_io_bram_ps 0>, <&vccint_io_bram_ps 1>, <&vccint_io_bram_ps 2>, <&vccint_io_bram_ps 3>;
+	};
+	ina226-vcc1v8 {
+		compatible = "iio-hwmon";
+		io-channels = <&vcc1v8 0>, <&vcc1v8 1>, <&vcc1v8 2>, <&vcc1v8 3>;
+	};
+	ina226-vcc1v2 {
+		compatible = "iio-hwmon";
+		io-channels = <&vcc1v2 0>, <&vcc1v2 1>, <&vcc1v2 2>, <&vcc1v2 3>;
+	};
+	ina226-vadj-fmc {
+		compatible = "iio-hwmon";
+		io-channels = <&vadj_fmc 0>, <&vadj_fmc 1>, <&vadj_fmc 2>, <&vadj_fmc 3>;
+	};
+	ina226-mgtavcc {
+		compatible = "iio-hwmon";
+		io-channels = <&mgtavcc 0>, <&mgtavcc 1>, <&mgtavcc 2>, <&mgtavcc 3>;
+	};
+	ina226-mgt1v2 {
+		compatible = "iio-hwmon";
+		io-channels = <&mgt1v2 0>, <&mgt1v2 1>, <&mgt1v2 2>, <&mgt1v2 3>;
+	};
+	ina226-mgt1v8 {
+		compatible = "iio-hwmon";
+		io-channels = <&mgt1v8 0>, <&mgt1v8 1>, <&mgt1v8 2>, <&mgt1v8 3>;
+	};
+	ina226-vccint-ams {
+		compatible = "iio-hwmon";
+		io-channels = <&vccint_ams 0>, <&vccint_ams 1>, <&vccint_ams 2>, <&vccint_ams 3>;
+	};
+	ina226-dac-avtt {
+		compatible = "iio-hwmon";
+		io-channels = <&dac_avtt 0>, <&dac_avtt 1>, <&dac_avtt 2>, <&dac_avtt 3>;
+	};
+	ina226-dac-avccaux {
+		compatible = "iio-hwmon";
+		io-channels = <&dac_avccaux 0>, <&dac_avccaux 1>, <&dac_avccaux 2>, <&dac_avccaux 3>;
+	};
+	ina226-adc-avcc {
+		compatible = "iio-hwmon";
+		io-channels = <&adc_avcc 0>, <&adc_avcc 1>, <&adc_avcc 2>, <&adc_avcc 3>;
+	};
+	ina226-adc-avccaux {
+		compatible = "iio-hwmon";
+		io-channels = <&adc_avccaux 0>, <&adc_avccaux 1>, <&adc_avccaux 2>, <&adc_avccaux 3>;
+	};
+	ina226-dac-avcc {
+		compatible = "iio-hwmon";
+		io-channels = <&dac_avcc 0>, <&dac_avcc 1>, <&dac_avcc 2>, <&dac_avcc 3>;
+	};
+};
+
+&dcc {
+	status = "okay";
+};
+
+&fpd_dma_chan1 {
+	status = "okay";
+};
+
+&fpd_dma_chan2 {
+	status = "okay";
+};
+
+&fpd_dma_chan3 {
+	status = "okay";
+};
+
+&fpd_dma_chan4 {
+	status = "okay";
+};
+
+&fpd_dma_chan5 {
+	status = "okay";
+};
+
+&fpd_dma_chan6 {
+	status = "okay";
+};
+
+&fpd_dma_chan7 {
+	status = "okay";
+};
+
+&fpd_dma_chan8 {
+	status = "okay";
+};
+
+&gem3 {
+	status = "okay";
+	phy-handle = <&phy0>;
+	phy-mode = "rgmii-id";
+	phy0: ethernet-phy@c {
+		reg = <0xc>;
+		ti,rx-internal-delay = <0x8>;
+		ti,tx-internal-delay = <0xa>;
+		ti,fifo-depth = <0x1>;
+		ti,dp83867-rxctrl-strap-quirk;
+	};
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names = "QSPI_LWR_CLK", "QSPI_LWR_DQ1", "QSPI_LWR_DQ2", "QSPI_LWR_DQ3", "QSPI_LWR_DQ0", /* 0 - 4 */
+		  "QSPI_LWR_CS_B", "", "QSPI_UPR_CS_B", "QSPI_UPR_DQ0", "QSPI_UPR_DQ1", /* 5 - 9 */
+		  "QSPI_UPR_DQ2", "QSPI_UPR_DQ3", "QSPI_UPR_CLK", "PS_GPIO2", "I2C0_SCL", /* 10 - 14 */
+		  "I2C0_SDA", "I2C1_SCL", "I2C1_SDA", "UART0_TXD", "UART0_RXD", /* 15 - 19 */
+		  "", "", "BUTTON", "LED", "", /* 20 - 24 */
+		  "", "PMU_INPUT", "", "", "", /* 25 - 29 */
+		  "", "", "PMU_GPO0", "PMU_GPO1", "PMU_GPO2", /* 30 - 34 */
+		  "PMU_GPO3", "PMU_GPO4", "PMU_GPO5", "PS_GPIO1", "SDIO_SEL", /* 35 - 39 */
+		  "SDIO_DIR_CMD", "SDIO_DIR_DAT0", "SDIO_DIR_DAT1", "", "", /* 40 - 44 */
+		  "SDIO_DETECT", "SDIO_DAT0", "SDIO_DAT1", "SDIO_DAT2", "SDIO_DAT3", /* 45 - 49 */
+		  "SDIO_CMD", "SDIO_CLK", "USB_CLK", "USB_DIR", "USB_DATA2", /* 50 - 54 */
+		  "USB_NXT", "USB_DATA0", "USB_DATA1", "USB_STP", "USB_DATA3", /* 55 - 59 */
+		  "USB_DATA4", "USB_DATA5", "USB_DATA6", "USB_DATA7", "ENET_TX_CLK", /* 60 - 64 */
+		  "ENET_TX_D0", "ENET_TX_D1", "ENET_TX_D2", "ENET_TX_D3", "ENET_TX_CTRL", /* 65 - 69 */
+		  "ENET_RX_CLK", "ENET_RX_D0", "ENET_RX_D1", "ENET_RX_D2", "ENET_RX_D3", /* 70 - 74 */
+		  "ENET_RX_CTRL", "ENET_MDC", "ENET_MDIO", /* 75 - 77, MIO end and EMIO start */
+		  "", "", /* 78 - 79 */
+		  "", "", "", "", "", /* 80 - 84 */
+		  "", "", "", "", "", /* 85 -89 */
+		  "", "", "", "", "", /* 90 - 94 */
+		  "", "", "", "", "", /* 95 - 99 */
+		  "", "", "", "", "", /* 100 - 104 */
+		  "", "", "", "", "", /* 105 - 109 */
+		  "", "", "", "", "", /* 110 - 114 */
+		  "", "", "", "", "", /* 115 - 119 */
+		  "", "", "", "", "", /* 120 - 124 */
+		  "", "", "", "", "", /* 125 - 129 */
+		  "", "", "", "", "", /* 130 - 134 */
+		  "", "", "", "", "", /* 135 - 139 */
+		  "", "", "", "", "", /* 140 - 144 */
+		  "", "", "", "", "", /* 145 - 149 */
+		  "", "", "", "", "", /* 150 - 154 */
+		  "", "", "", "", "", /* 155 - 159 */
+		  "", "", "", "", "", /* 160 - 164 */
+		  "", "", "", "", "", /* 165 - 169 */
+		  "", "", "", ""; /* 170 - 174 */
+};
+
+&i2c0 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	tca6416_u15: gpio@20 { /* u15 */
+		compatible = "ti,tca6416";
+		reg = <0x20>;
+		gpio-controller; /* interrupt not connected */
+		#gpio-cells = <2>;
+		gpio-line-names = "MAX6643_OT_B", "MAX6643_FANFAIL_B", "MIO26_PMU_INPUT_LS", "DAC_AVTT_VOUT_SEL", /* 0 - 3 */
+				  "", "IIC_MUX_RESET_B", "GEM3_EXP_RESET_B", "MAX6643_FULL_SPEED", /* 4 - 7 */
+				  "FMCP_HSPC_PRSNT_M2C_B", "", "", "VCCINT_VRHOT_B", /* 10 - 13 */
+				  "", "8A34001_EXP_RST_B", "IRPS5401_ALERT_B", "INA226_PMBUS_ALERT"; /* 14 - 17 */
+	};
+
+	i2c-mux@75 { /* u17 */
+		compatible = "nxp,pca9544";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x75>;
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/* PS_PMBUS */
+			/* PMBUS_ALERT done via pca9544 */
+			vccint: ina226@40 { /* u65 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vccint";
+				reg = <0x40>;
+				shunt-resistor = <5000>;
+			};
+			vccint_io_bram_ps: ina226@41 { /* u57 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vccint-io-bram-ps";
+				reg = <0x41>;
+				shunt-resistor = <5000>;
+			};
+			vcc1v8: ina226@42 { /* u60 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcc1v8";
+				reg = <0x42>;
+				shunt-resistor = <2000>;
+			};
+			vcc1v2: ina226@43 { /* u58 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vcc1v2";
+				reg = <0x43>;
+				shunt-resistor = <5000>;
+			};
+			vadj_fmc: ina226@45 { /* u62 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vadj-fmc";
+				reg = <0x45>;
+				shunt-resistor = <5000>;
+			};
+			mgtavcc: ina226@46 { /* u67 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-mgtavcc";
+				reg = <0x46>;
+				shunt-resistor = <2000>;
+			};
+			mgt1v2: ina226@47 { /* u63 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-mgt1v2";
+				reg = <0x47>;
+				shunt-resistor = <5000>;
+			};
+			mgt1v8: ina226@48 { /* u64 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-mgt1v8";
+				reg = <0x48>;
+				shunt-resistor = <5000>;
+			};
+			vccint_ams: ina226@49 { /* u61 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-vccint-ams";
+				reg = <0x49>;
+				shunt-resistor = <5000>;
+			};
+			dac_avtt: ina226@4a { /* u59 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-dac-avtt";
+				reg = <0x4a>;
+				shunt-resistor = <5000>;
+			};
+			dac_avccaux: ina226@4b { /* u124 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-dac-avccaux";
+				reg = <0x4b>;
+				shunt-resistor = <5000>;
+			};
+			adc_avcc: ina226@4c { /* u75 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-adc-avcc";
+				reg = <0x4c>;
+				shunt-resistor = <5000>;
+			};
+			adc_avccaux: ina226@4d { /* u71 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-adc-avccaux";
+				reg = <0x4d>;
+				shunt-resistor = <5000>;
+			};
+			dac_avcc: ina226@4e { /* u77 */
+				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
+				label = "ina226-dac-avcc";
+				reg = <0x4e>;
+				shunt-resistor = <5000>;
+			};
+		};
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			/* NC */
+		};
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			/* u104 - ir35215 0x10/0x40 */
+			/* u127 - ir38164 0x1b/0x4b */
+			/* u112 - ir38164 0x13/0x43 */
+			/* u123 - ir38164 0x1c/0x4c */
+
+			irps5401_44: irps54012@44 { /* IRPS5401 - u53 */
+				#clock-cells = <0>;
+				compatible = "infineon,irps5401";
+				reg = <0x44>; /* i2c addr 0x14 */
+			};
+			irps5401_45: irps54012@45 { /* IRPS5401 - u55 */
+				#clock-cells = <0>;
+				compatible = "infineon,irps5401";
+				reg = <0x45>; /* i2c addr 0x15 */
+			};
+			/* J21 header too */
+
+		};
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			/* SYSMON */
+		};
+	};
+	/* u38 MPS430 */
+};
+
+&i2c1 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	i2c-mux@74 {
+		compatible = "nxp,pca9548"; /* u20 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+		/* FIXME reset-gpios = <&tca6416_u15 SYSCTLR_IIC_MUX0_RESET_B GPIO_ACTIVE_HIGH>; */
+		i2c_eeprom: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/*
+			 * IIC_EEPROM 1kB memory which uses 256B blocks
+			 * where every block has different address.
+			 *    0 - 256B address 0x54
+			 * 256B - 512B address 0x55
+			 * 512B - 768B address 0x56
+			 * 768B - 1024B address 0x57
+			 */
+			eeprom: eeprom@54 { /* u21 */
+				compatible = "atmel,24c128";
+				reg = <0x54>;
+			};
+		};
+		i2c_si5341: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			si5341: clock-generator@36 { /* SI5341 - u43 */
+				compatible = "si5341";
+				reg = <0x36>;
+			};
+
+		};
+		i2c_si570_user_c0: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			si570_1: clock-generator@5d { /* USER C0 SI570 - u47 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>;
+				temperature-stability = <50>;
+				factory-fout = <300000000>;
+				clock-frequency = <300000000>;
+				clock-output-names = "si570_user_c0";
+			};
+		};
+		i2c_si570_mgt: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			si570_2: clock-generator@5d { /* USER MGT SI570 - u48 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>;
+				temperature-stability = <50>;
+				factory-fout = <156250000>;
+				clock-frequency = <148500000>;
+				clock-output-names = "si570_mgt";
+			};
+		};
+		i2c_8a34001: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			/* U409B - 8a34001 */
+		};
+		i2c_clk104: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+			/* CLK104_SDA */
+		};
+		i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+			/* RFMCP connector */
+		};
+		/* 7 NC */
+	};
+
+	i2c-mux@75 {
+		compatible = "nxp,pca9548"; /* u22 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x75>;
+		/* FIXME reset-gpios = <&tca6416_u15 SYSCTLR_IIC_MUX0_RESET_B GPIO_ACTIVE_HIGH>; */
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			/* FMCP_HSPC_IIC */
+		};
+		i2c_si570_user_c1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			si570_3: clock-generator@5d { /* USER C1 SI570 - u130 */
+				#clock-cells = <0>;
+				compatible = "silabs,si570";
+				reg = <0x5d>;
+				temperature-stability = <50>;
+				factory-fout = <300000000>;
+				clock-frequency = <300000000>;
+				clock-output-names = "si570_user_c1";
+			};
+		};
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			/* SYSMON */
+		};
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			/* DDR4 SODIMM */
+		};
+		i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+			/* SFP3 */
+		};
+		i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+			/* SFP2 */
+		};
+		i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+			/* SFP1 */
+		};
+		i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+			/* SFP0 */
+		};
+	};
+	/* MSP430 */
+};
+
+&qspi {
+	status = "okay";
+	is-dual = <1>;
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor"; /* U11 and U12 MT25QU02GCBBE12 1Gb */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>; /* FIXME also DUAL configuration possible */
+		spi-max-frequency = <108000000>; /* Based on DC1 spec */
+	};
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+	/* SATA OOB timing settings */
+	ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+	ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+	ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+	ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+	ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+	ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+	ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+	ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+	phy-names = "sata-phy";
+	phys = <&lane3 PHY_TYPE_SATA 1 3 125000000>;
+};
+
+/* SD1 with level shifter */
+&sdhci1 {
+	status = "okay";
+	disable-wp;
+	xlnx,mio_bank = <1>;
+};
+
+&serdes {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+/* ULPI SMSC USB3320 */
+&usb0 {
+	status = "okay";
+};
+
+&dwc3_0 {
+	status = "okay";
+	dr_mode = "host";
+	snps,usb3_lpm_capable;
+	phy-names = "usb3-phy";
+	phys = <&lane2 PHY_TYPE_USB3 0 2 26000000>;
+};
diff --git a/arch/arm/dts/zynqmp-zcu216-revA.dts b/arch/arm/dts/zynqmp-zcu216-revA.dts
index dd9cd7b..c294e1b 100644
--- a/arch/arm/dts/zynqmp-zcu216-revA.dts
+++ b/arch/arm/dts/zynqmp-zcu216-revA.dts
@@ -253,7 +253,7 @@
 				#io-channel-cells = <1>;
 				label = "ina226-vccint-io-bram-ps";
 				reg = <0x41>;
-				shunt-resistor = <2000>;
+				shunt-resistor = <5000>;
 			};
 			vcc1v8: ina226@42 { /* u60 */
 				compatible = "ti,ina226";
@@ -302,7 +302,7 @@
 				#io-channel-cells = <1>;
 				label = "ina226-vccint-ams";
 				reg = <0x49>;
-				shunt-resistor = <2000>;
+				shunt-resistor = <5000>;
 			};
 			dac_avtt: ina226@4a { /* u59 */
 				compatible = "ti,ina226";
@@ -401,7 +401,7 @@
 			 * 768B - 1024B address 0x57
 			 */
 			eeprom: eeprom@54 { /* u21 */
-				compatible = "atmel,24c08";
+				compatible = "atmel,24c128";
 				reg = <0x54>;
 			};
 		};
diff --git a/arch/arm/dts/zynqmp.dtsi b/arch/arm/dts/zynqmp.dtsi
index b453941..9e7fae8 100644
--- a/arch/arm/dts/zynqmp.dtsi
+++ b/arch/arm/dts/zynqmp.dtsi
@@ -25,7 +25,7 @@
 		#size-cells = <0>;
 
 		cpu0: cpu@0 {
-			compatible = "arm,cortex-a53", "arm,armv8";
+			compatible = "arm,cortex-a53";
 			device_type = "cpu";
 			enable-method = "psci";
 			operating-points-v2 = <&cpu_opp_table>;
@@ -34,7 +34,7 @@
 		};
 
 		cpu1: cpu@1 {
-			compatible = "arm,cortex-a53", "arm,armv8";
+			compatible = "arm,cortex-a53";
 			device_type = "cpu";
 			enable-method = "psci";
 			reg = <0x1>;
@@ -43,7 +43,7 @@
 		};
 
 		cpu2: cpu@2 {
-			compatible = "arm,cortex-a53", "arm,armv8";
+			compatible = "arm,cortex-a53";
 			device_type = "cpu";
 			enable-method = "psci";
 			reg = <0x2>;
@@ -52,7 +52,7 @@
 		};
 
 		cpu3: cpu@3 {
-			compatible = "arm,cortex-a53", "arm,armv8";
+			compatible = "arm,cortex-a53";
 			device_type = "cpu";
 			enable-method = "psci";
 			reg = <0x3>;
@@ -74,7 +74,7 @@
 		};
 	};
 
-	cpu_opp_table: cpu_opp_table {
+	cpu_opp_table: cpu-opp-table {
 		compatible = "operating-points-v2";
 		opp-shared;
 		opp00 {
@@ -252,7 +252,7 @@
 		};
 	};
 
-	amba_apu: amba_apu@0 {
+	amba_apu: amba-apu@0 {
 		compatible = "simple-bus";
 		#address-cells = <2>;
 		#size-cells = <1>;
@@ -626,12 +626,12 @@
 			compatible = "xlnx,zynqmp-gpio-1.0";
 			status = "disabled";
 			#gpio-cells = <0x2>;
+			gpio-controller;
 			interrupt-parent = <&gic>;
 			interrupts = <0 16 4>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
 			reg = <0x0 0xff0a0000 0x0 0x1000>;
-			gpio-controller;
 			power-domains = <&zynqmp_firmware PD_GPIO>;
 		};