ARM: add SBx81LIFKW board

This is a series of line cards for Allied Telesis's SBx8100 chassis
switch. The CPU block is common to the SBx81GS24a, SBx81XS6, SBx81XS16
and SBx81GT40 cards collectively referred to as SBx81LIFKW in u-boot.

Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>

9 files changed, 554 insertions, 0 deletions

diff --git a/arch/arm/dts/kirkwood-atl-sbx81lifkw.dts b/arch/arm/dts/kirkwood-atl-sbx81lifkw.dts
new file mode 100644
index 0000000..e5b1efa
--- /dev/null
+++ b/arch/arm/dts/kirkwood-atl-sbx81lifkw.dts
@@ -0,0 +1,133 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+	model = "Allied Telesis SBx81LIFKW Board";
+	compatible = "atl,SBx81LIFKW", "marvell,kirkwood-88f6281",
+		     "marvell,kirkwood";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>; /* 128 MB */
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 earlyprintk";
+		stdout-path = &uart0;
+	};
+
+	aliases {
+		ethernet0 = &eth0;
+		i2c0 = &i2c0;
+		spi0 = &spi0;
+	};
+
+	dsa {
+		compatible = "marvell,dsa";
+		#address-cells = <2>;
+		#size-cells = <0>;
+		dsa,ethernet = <&eth0>;
+		dsa,mii-bus = <&mdio>;
+		status = "okay";
+
+		switch@0 {
+			#address-cells =  <1>;
+			#size-cells = <0>;
+			reg = <1 0>;
+
+			port@0 {
+				reg = <0>;
+				label = "internal0";
+			};
+			port@1 {
+				reg = <1>;
+				label = "internal1";
+			};
+			port@8 {
+				reg = <8>;
+				label = "internal8";
+				phy-mode = "rgmii-id";
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+			port@9 {
+				reg = <9>;
+				label = "internal9";
+				phy-mode = "rgmii-id";
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+			port@10 {
+				reg = <10>;
+				label = "cpu";
+			};
+		};
+	};
+};
+
+&spi0 {
+	status = "okay";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "st,m25p128", "jedec,spi-nor", "spi-flash";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+		mode = <0>;
+
+		partition@u-boot {
+			reg = <0x00000000 0x00c00000>;
+			label = "u-boot";
+		};
+		partition@u-boot-env {
+			reg = <0x00c00000 0x00040000>;
+			label = "u-boot-env";
+		};
+		partition@unused {
+			reg = <0x00100000 0x00f00000>;
+			label = "unused";
+		};
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	eeprom@52 {
+		compatible = "atmel,24c04";
+		reg = <0x52>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&mdio {
+	status = "okay";
+};
+
+&eth0 {
+	status = "okay";
+
+	ethernet0-port@0 {
+		speed = <1000>;
+		duplex = <1>;
+	};
+};
+
+&pciec {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig
index 2dd107a..5a5a63c 100644
--- a/arch/arm/mach-kirkwood/Kconfig
+++ b/arch/arm/mach-kirkwood/Kconfig
@@ -59,6 +59,9 @@ config TARGET_NAS220
 config TARGET_NSA310S
 	bool "Zyxel NSA310S"
 
+config TARGET_SBx81LIFKW
+	bool "Allied Telesis SBx81GS24/SBx81GT40/SBx81XS6/SBx81XS16"
+
 endchoice
 
 config SYS_SOC
@@ -81,5 +84,6 @@ source "board/Seagate/dockstar/Kconfig"
 source "board/Seagate/goflexhome/Kconfig"
 source "board/Seagate/nas220/Kconfig"
 source "board/zyxel/nsa310s/Kconfig"
+source "board/alliedtelesis/SBx81LIFKW/Kconfig"
 
 endif
diff --git a/board/alliedtelesis/SBx81LIFKW/Kconfig b/board/alliedtelesis/SBx81LIFKW/Kconfig
new file mode 100644
index 0000000..5c2609b
--- /dev/null
+++ b/board/alliedtelesis/SBx81LIFKW/Kconfig
@@ -0,0 +1,12 @@
+if TARGET_SBx81LIFKW
+
+config SYS_BOARD
+       default "SBx81LIFKW"
+
+config SYS_VENDOR
+       default "alliedtelesis"
+
+config SYS_CONFIG_NAME
+       default "SBx81LIFKW"
+
+endif
diff --git a/board/alliedtelesis/SBx81LIFKW/MAINTAINERS b/board/alliedtelesis/SBx81LIFKW/MAINTAINERS
new file mode 100644
index 0000000..31ccec0
--- /dev/null
+++ b/board/alliedtelesis/SBx81LIFKW/MAINTAINERS
@@ -0,0 +1,7 @@
+SBx81LIFKW BOARD
+M:	Chris Packham <chris.packham@alliedtelesis.co.nz>
+S:	Maintained
+F:	board/alliedtelesis/SBx81LIFKW/
+F:	include/configs/SBx81LIFKW
+F:	configs/SBx81LIFKW_defconfig
+F:	arch/arm/dts/kirkwood-atl-sbx81lifkw.dts
diff --git a/board/alliedtelesis/SBx81LIFKW/Makefile b/board/alliedtelesis/SBx81LIFKW/Makefile
new file mode 100644
index 0000000..806020e
--- /dev/null
+++ b/board/alliedtelesis/SBx81LIFKW/Makefile
@@ -0,0 +1,7 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# (C) Copyright 2010, 2018
+# Allied Telesis <www.alliedtelesis.com>
+#
+
+obj-y	+= sbx81lifkw.o
diff --git a/board/alliedtelesis/SBx81LIFKW/kwbimage.cfg b/board/alliedtelesis/SBx81LIFKW/kwbimage.cfg
new file mode 100644
index 0000000..9726f15
--- /dev/null
+++ b/board/alliedtelesis/SBx81LIFKW/kwbimage.cfg
@@ -0,0 +1,47 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# (C) Copyright 2018 Allied Telesis
+#
+# Refer docs/README.kwimage for more details about how-to configure
+# and create kirkwood boot image
+#
+
+# Boot Media configurations
+BOOT_FROM	spi	# Boot from SPI flash
+
+# SOC registers configuration using bootrom header extension
+# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
+DATA 0xffd100e0 0x1b1b1b1b
+DATA 0xffd20134 0xffffffff
+DATA 0xffd20138 0x009fffff
+DATA 0xffd20154 0x00000000
+DATA 0xffd2014c 0x00000000
+DATA 0xffd20148 0x00000001
+
+# Dram initalization for 1 x x16
+#  DDR II Micron part number MT47H64M16HR-3
+#  MClk 333MHz, Size 128MB, ECC disable
+#
+DATA 0xffd01400 0x43000618
+DATA 0xffd01404 0x35143000
+DATA 0xffd01408 0x11012227
+DATA 0xffd0140c 0x00000819
+DATA 0xffd01410 0x0000000d
+DATA 0xffd01414 0x00000000
+DATA 0xffd01418 0x00000000
+DATA 0xffd0141c 0x00000632
+DATA 0xffd01420 0x00000040
+DATA 0xffd01424 0x0000f07f
+DATA 0xffd01500 0x00000000	# SDRAM CS[0] Base address at 0x00000000
+DATA 0xffd01504 0x07FFFFF1	# SDRAM CS[0] Size 128MiB
+DATA 0xffd01508 0x10000000
+DATA 0xffd0150c 0x00FFFFF4	# SDRAM CS[1] Size, window disabled
+DATA 0xffd01514 0x00FFFFF8	# SDRAM CS[2] Size, window disabled
+DATA 0xffd0151c 0x00FFFFFC	# SDRAM CS[3] Size, window disabled
+DATA 0xffd01494 0x00030000
+DATA 0xffd01498 0x00000000
+DATA 0xffd0149c 0x0000e803
+DATA 0xffd01480 0x00000001
+
+# End of Header extension
+DATA 0x0 0x0
diff --git a/board/alliedtelesis/SBx81LIFKW/sbx81lifkw.c b/board/alliedtelesis/SBx81LIFKW/sbx81lifkw.c
new file mode 100644
index 0000000..3cacdc8
--- /dev/null
+++ b/board/alliedtelesis/SBx81LIFKW/sbx81lifkw.c
@@ -0,0 +1,187 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2010, 2018
+ * Allied Telesis <www.alliedtelesis.com>
+ */
+
+#include <common.h>
+#include <linux/io.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/soc.h>
+#include <asm/arch/mpp.h>
+#include <asm/arch/gpio.h>
+
+/* Note: GPIO differences between specific boards
+ *
+ * We're trying to avoid having multiple build targets for all the Kirkwood
+ * based boards one area where things tend to differ is GPIO usage. For the
+ * most part the GPIOs driven by the bootloader are similar enough in function
+ * that there is no harm in driving them.
+ *
+ *         XZ4  XS6     XS16  GS24A         GT40   GP24A         GT24A
+ * GPIO39  -    INT(<)  NC    MUX_RST_N(>)  NC     POE_DIS_N(>)  NC
+ */
+
+#define SBX81LIFKW_OE_LOW	~(BIT(31) | BIT(30) | BIT(28) | BIT(27) | \
+				  BIT(18) | BIT(17) | BIT(13) | BIT(12) | \
+				  BIT(10))
+#define SBX81LIFKW_OE_HIGH	~(BIT(0) | BIT(1) | BIT(7))
+#define SBX81LIFKW_OE_VAL_LOW	 (BIT(31) | BIT(30) | BIT(28) | BIT(27))
+#define SBX81LIFKW_OE_VAL_HIGH	 (BIT(0) | BIT(1))
+
+#define MV88E6097_RESET		27
+
+DECLARE_GLOBAL_DATA_PTR;
+
+struct led {
+	u32 reg;
+	u32 value;
+	u32 mask;
+};
+
+struct led amber_solid = {
+	MVEBU_GPIO0_BASE,
+	BIT(10),
+	BIT(18) | BIT(10)
+};
+
+struct led green_solid = {
+	MVEBU_GPIO0_BASE,
+	BIT(18) | BIT(10),
+	BIT(18) | BIT(10)
+};
+
+struct led amber_flash = {
+	MVEBU_GPIO0_BASE,
+	0,
+	BIT(18) | BIT(10)
+};
+
+struct led green_flash = {
+	MVEBU_GPIO0_BASE,
+	BIT(18),
+	BIT(18) | BIT(10)
+};
+
+static void status_led_set(struct led *led)
+{
+	clrsetbits_le32(led->reg, led->mask, led->value);
+}
+
+int board_early_init_f(void)
+{
+	/*
+	 * default gpio configuration
+	 * There are maximum 64 gpios controlled through 2 sets of registers
+	 * the  below configuration configures mainly initial LED status
+	 */
+	mvebu_config_gpio(SBX81LIFKW_OE_VAL_LOW,
+			  SBX81LIFKW_OE_VAL_HIGH,
+			  SBX81LIFKW_OE_LOW, SBX81LIFKW_OE_HIGH);
+
+	/* Multi-Purpose Pins Functionality configuration */
+	static const u32 kwmpp_config[] = {
+		MPP0_SPI_SCn,
+		MPP1_SPI_MOSI,
+		MPP2_SPI_SCK,
+		MPP3_SPI_MISO,
+		MPP4_UART0_RXD,
+		MPP5_UART0_TXD,
+		MPP6_SYSRST_OUTn,
+		MPP7_PEX_RST_OUTn,
+		MPP8_TW_SDA,
+		MPP9_TW_SCK,
+		MPP10_GPO,
+		MPP11_GPIO,
+		MPP12_GPO,
+		MPP13_GPIO,
+		MPP14_GPIO,
+		MPP15_UART0_RTS,
+		MPP16_UART0_CTS,
+		MPP17_GPIO,
+		MPP18_GPO,
+		MPP19_GPO,
+		MPP20_GPIO,
+		MPP21_GPIO,
+		MPP22_GPIO,
+		MPP23_GPIO,
+		MPP24_GPIO,
+		MPP25_GPIO,
+		MPP26_GPIO,
+		MPP27_GPIO,
+		MPP28_GPIO,
+		MPP29_GPIO,
+		MPP30_GPIO,
+		MPP31_GPIO,
+		MPP32_GPIO,
+		MPP33_GPIO,
+		MPP34_GPIO,
+		MPP35_GPIO,
+		MPP36_GPIO,
+		MPP37_GPIO,
+		MPP38_GPIO,
+		MPP39_GPIO,
+		MPP40_GPIO,
+		MPP41_GPIO,
+		MPP42_GPIO,
+		MPP43_GPIO,
+		MPP44_GPIO,
+		MPP45_GPIO,
+		MPP46_GPIO,
+		MPP47_GPIO,
+		MPP48_GPIO,
+		MPP49_GPIO,
+		0
+	};
+
+	kirkwood_mpp_conf(kwmpp_config, NULL);
+	return 0;
+}
+
+int board_init(void)
+{
+	/* Power-down unused subsystems. The required
+	 * subsystems are:
+	 *
+	 *  GE0         b0
+	 *  PEX0 PHY    b1
+	 *  PEX0.0      b2
+	 *  TSU         b5
+	 *  SDRAM       b6
+	 *  RUNIT       b7
+	 */
+	writel((BIT(0) | BIT(1) | BIT(2) |
+		BIT(5) | BIT(6) | BIT(7)),
+		KW_CPU_REG_BASE + 0x1c);
+
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
+
+	status_led_set(&amber_solid);
+
+	return 0;
+}
+
+#ifdef CONFIG_MV88E61XX_SWITCH
+/* Configure and enable Switch and PHY */
+void reset_phy(void)
+{
+	/* Ensure the 88e6097 gets at least 10ms Reset
+	 */
+	kw_gpio_set_value(MV88E6097_RESET, 0);
+	mdelay(20);
+	kw_gpio_set_value(MV88E6097_RESET, 1);
+	mdelay(20);
+}
+#endif
+
+#ifdef CONFIG_MISC_INIT_R
+int misc_init_r(void)
+{
+	status_led_set(&green_flash);
+
+	return 0;
+}
+#endif
diff --git a/configs/SBx81LIFKW_defconfig b/configs/SBx81LIFKW_defconfig
new file mode 100644
index 0000000..ec9df1a
--- /dev/null
+++ b/configs/SBx81LIFKW_defconfig
@@ -0,0 +1,33 @@
+CONFIG_ARM=y
+CONFIG_KIRKWOOD=y
+CONFIG_SYS_TEXT_BASE=0x00600000
+CONFIG_TARGET_SBx81LIFKW=y
+CONFIG_IDENT_STRING="\nSBx81LIFKW"
+CONFIG_DEFAULT_DEVICE_TREE="kirkwood-atl-sbx81lifkw"
+# CONFIG_SYS_MALLOC_F is not set
+CONFIG_BOOTDELAY=3
+CONFIG_SILENT_CONSOLE=y
+CONFIG_SILENT_U_BOOT_ONLY=y
+CONFIG_HUSH_PARSER=y
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_I2C=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_DHCP=y
+CONFIG_BOOTP_NTPSERVER=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_SNTP=y
+CONFIG_OF_CONTROL=y
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_DM=y
+CONFIG_DM_GPIO=y
+CONFIG_DM_PCA953X=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_MVTWSI=y
+CONFIG_I2C_MUX=y
+CONFIG_I2C_MUX_PCA954x=y
+# CONFIG_MMC is not set
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_STMICRO=y
+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
+CONFIG_SPI=y
+CONFIG_KIRKWOOD_SPI=y
diff --git a/include/configs/SBx81LIFKW.h b/include/configs/SBx81LIFKW.h
new file mode 100644
index 0000000..756eaa4
--- /dev/null
+++ b/include/configs/SBx81LIFKW.h
@@ -0,0 +1,124 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * (C) Copyright 2016 Allied Telesis <www.alliedtelesis.co.nz>
+ */
+
+#ifndef _CONFIG_SBX81LIFKW_H
+#define _CONFIG_SBX81LIFKW_H
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_FEROCEON_88FR131	1	/* CPU Core subversion */
+#define CONFIG_KW88F6281	1	/* SOC Name */
+#define CONFIG_SKIP_LOWLEVEL_INIT	/* disable board lowlevel_init */
+#define CONFIG_SYS_KWD_CONFIG	$(CONFIG_BOARDDIR)/kwbimage.cfg
+#define CONFIG_BUILD_TARGET	"u-boot.kwb"
+
+/* additions for new ARM relocation support */
+#define CONFIG_SYS_SDRAM_BASE	0x00000000
+
+#define CONFIG_MD5	/* get_random_hex on krikwood needs MD5 support */
+#define CONFIG_KIRKWOOD_EGIGA_INIT	/* Enable GbePort0/1 for kernel */
+#define CONFIG_KIRKWOOD_PCIE_INIT	/* Enable PCIE Port0 */
+#define CONFIG_KIRKWOOD_RGMII_PAD_1V8	/* Set RGMII Pad voltage to 1.8V */
+#define CONFIG_KIRKWOOD_GPIO	1
+
+#define CONFIG_MISC_INIT_R		/* call misc_init_r */
+
+/*
+ * NS16550 Configuration
+ */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	(-4)
+#define CONFIG_SYS_NS16550_CLK		CONFIG_SYS_TCLK
+#define CONFIG_SYS_NS16550_COM1		KW_UART0_BASE
+
+/*
+ * Serial Port configuration
+ * The following definitions let you select what serial you want to use
+ * for your console driver.
+ */
+
+#define CONFIG_CONS_INDEX	1	/*Console on UART0 */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_CMDLINE_TAG	1	/* enable passing of ATAGs */
+#define CONFIG_INITRD_TAG	1	/* enable INITRD tag */
+#define CONFIG_SETUP_MEMORY_TAGS 1	/* enable memory tag */
+
+#define MTDPARTS_DEFAULT "mtdparts=spi0.0:768K(boot)ro,256K(boot-env),14M(user),1M(errlog)"
+#define MTDPARTS_MTDOOPS "errlog"
+#define CONFIG_DOS_PARTITION
+
+/*
+ *  Environment variables configurations
+ */
+#define CONFIG_ENV_SPI_BUS		0
+#define CONFIG_ENV_SPI_CS		0
+#define CONFIG_ENV_SPI_MAX_HZ		20000000	/* 20Mhz */
+#define CONFIG_ENV_SPI_MODE		CONFIG_SF_DEFAULT_MODE
+#define CONFIG_ENV_SECT_SIZE		0x40000		/* 256K */
+#define CONFIG_ENV_SIZE			0x02000
+#define CONFIG_ENV_OFFSET		0xc0000		/* env starts here - 768K */
+
+/*
+ * U-Boot bootcode configuration
+ */
+
+#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for monitor */
+#define CONFIG_SYS_MALLOC_LEN		  (4 << 20)	/* Reserve 4.0 MB for malloc */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Mem map for Linux*/
+
+/* size in bytes reserved for initial data */
+
+#include <asm/arch/config.h>
+/* There is no PHY directly connected so don't ask it for link status */
+#undef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
+
+/*
+ * Other required minimal configurations
+ */
+#define CONFIG_ARCH_CPU_INIT	/* call arch_cpu_init() */
+#define CONFIG_NR_DRAM_BANKS	4
+#define CONFIG_SYS_MEMTEST_START 0x00400000	/* 4M */
+#define CONFIG_SYS_MEMTEST_END	0x007fffff	/*(_8M -1) */
+#define CONFIG_SYS_RESET_ADDRESS 0xffff0000	/* Rst Vector Adr */
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_NETCONSOLE	/* include NetConsole support */
+#define CONFIG_NET_MULTI	/* specify more that one ports available */
+#define CONFIG_MII		/* expose smi over miiphy interface */
+#define CONFIG_PHYLIB
+#define CONFIG_MVGBE	/* Enable kirkwood Gbe Controller Driver */
+#define CONFIG_MVGBE_PORTS	{1, 0}	/* enable a single port */
+#define CONFIG_PHY_BASE_ADR	0x01
+#define CONFIG_ENV_OVERWRITE	/* ethaddr can be reprogrammed */
+#define CONFIG_RESET_PHY_R	/* use reset_phy() to init switch */
+#define CONFIG_MV88E61XX_SWITCH	/* Enable MV88E61XX switch driver */
+#define CONFIG_MV88E61XX_PHY_PORTS 0x303 /* Pt0,1,8,9 */
+#define CONFIG_MV88E61XX_CPU_PORT 10 /* 10(CPU) */
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * Time settings
+ */
+#define CONFIG_RTC_MV
+
+#define CONFIG_SYS_LOAD_ADDR  0x1000000      /* default location for tftp and bootm */
+
+#endif /* _CONFIG_SBX81LIFKW_H */