configs: Re-run migrationsWIP/fix-migrated-sym-test

As the CI test for stopping platforms from being merged that were
defining symbols that had Kconfig entries, a small number of symbols
needed to be migrated again.  Do so, and catch two cases the README
should also have been updated but was not.

Signed-off-by: Tom Rini <trini@konsulko.com>

14 files changed, 11 insertions, 56 deletions

diff --git a/README b/README
index 6bb8d6e..b2a61c6 100644
--- a/README
+++ b/README
@@ -565,13 +565,6 @@ The following options need to be configured:
 		boards with QUICC Engines require OF_QE to set UCC MAC
 		addresses
 
-		CONFIG_OF_SYSTEM_SETUP
-
-		Other code has addition modification that it wants to make
-		to the flat device tree before handing it off to the kernel.
-		This causes ft_system_setup() to be called before booting
-		the kernel.
-
 		CONFIG_OF_IDE_FIXUP
 
 		U-Boot can detect if an IDE device is present or not.
@@ -1847,10 +1840,6 @@ The following options need to be configured:
 		CONFIG_SPL_SKIP_RELOCATE
 		Avoid SPL relocation
 
-		CONFIG_SPL_NAND_IDENT
-		SPL uses the chip ID list to identify the NAND flash.
-		Requires CONFIG_SPL_NAND_BASE.
-
 		CONFIG_SPL_UBI
 		Support for a lightweight UBI (fastmap) scanner and
 		loader
diff --git a/configs/imx8mn_var_som_defconfig b/configs/imx8mn_var_som_defconfig
index 34b31d7..bb351a2 100644
--- a/configs/imx8mn_var_som_defconfig
+++ b/configs/imx8mn_var_som_defconfig
@@ -31,6 +31,7 @@ CONFIG_ARCH_MISC_INIT=y
 CONFIG_SPL_BOARD_INIT=y
 CONFIG_SPL_BOOTROM_SUPPORT=y
 CONFIG_SPL_SEPARATE_BSS=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
 CONFIG_SPL_I2C=y
 CONFIG_SPL_POWER=y
 CONFIG_SPL_WATCHDOG=y
diff --git a/configs/imx8mp_rsb3720a1_4G_defconfig b/configs/imx8mp_rsb3720a1_4G_defconfig
index b9480bb..096061f 100644
--- a/configs/imx8mp_rsb3720a1_4G_defconfig
+++ b/configs/imx8mp_rsb3720a1_4G_defconfig
@@ -21,8 +21,10 @@ CONFIG_SPL_MMC=y
 CONFIG_SPL_SERIAL=y
 CONFIG_SPL_DRIVERS_MISC=y
 CONFIG_SPL=y
+CONFIG_IMX_BOOTAUX=y
 CONFIG_SPL_IMX_ROMAPI_LOADADDR=0x48000000
 CONFIG_DISTRO_DEFAULTS=y
+CONFIG_REMAKE_ELF=y
 CONFIG_SYS_LOAD_ADDR=0x40480000
 CONFIG_FIT=y
 CONFIG_FIT_EXTERNAL_OFFSET=0x3000
diff --git a/configs/imx8mp_rsb3720a1_6G_defconfig b/configs/imx8mp_rsb3720a1_6G_defconfig
index fe60b81..b46f37c 100644
--- a/configs/imx8mp_rsb3720a1_6G_defconfig
+++ b/configs/imx8mp_rsb3720a1_6G_defconfig
@@ -21,8 +21,10 @@ CONFIG_SPL_MMC=y
 CONFIG_SPL_SERIAL=y
 CONFIG_SPL_DRIVERS_MISC=y
 CONFIG_SPL=y
+CONFIG_IMX_BOOTAUX=y
 CONFIG_SPL_IMX_ROMAPI_LOADADDR=0x48000000
 CONFIG_DISTRO_DEFAULTS=y
+CONFIG_REMAKE_ELF=y
 CONFIG_SYS_LOAD_ADDR=0x40480000
 CONFIG_FIT=y
 CONFIG_FIT_EXTERNAL_OFFSET=0x3000
diff --git a/configs/j721s2_evm_a72_defconfig b/configs/j721s2_evm_a72_defconfig
index f4dc095..7e2bbc4 100644
--- a/configs/j721s2_evm_a72_defconfig
+++ b/configs/j721s2_evm_a72_defconfig
@@ -135,6 +135,7 @@ CONFIG_CFI_FLASH=y
 CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
 CONFIG_FLASH_CFI_MTD=y
 CONFIG_SYS_FLASH_CFI=y
+CONFIG_SYS_MAX_FLASH_BANKS_DETECT=y
 CONFIG_DM_SPI_FLASH=y
 CONFIG_SPI_FLASH_SFDP_SUPPORT=y
 CONFIG_SPI_FLASH_SOFT_RESET=y
diff --git a/configs/j721s2_evm_r5_defconfig b/configs/j721s2_evm_r5_defconfig
index 09f832e..996efd4 100644
--- a/configs/j721s2_evm_r5_defconfig
+++ b/configs/j721s2_evm_r5_defconfig
@@ -111,6 +111,7 @@ CONFIG_CFI_FLASH=y
 CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
 CONFIG_FLASH_CFI_MTD=y
 CONFIG_SYS_FLASH_CFI=y
+CONFIG_SYS_MAX_FLASH_BANKS_DETECT=y
 CONFIG_DM_SPI_FLASH=y
 CONFIG_SPI_FLASH_SFDP_SUPPORT=y
 CONFIG_SPI_FLASH_SOFT_RESET=y
diff --git a/configs/kontron_pitx_imx8m_defconfig b/configs/kontron_pitx_imx8m_defconfig
index 7643021..0f6bc3f 100644
--- a/configs/kontron_pitx_imx8m_defconfig
+++ b/configs/kontron_pitx_imx8m_defconfig
@@ -20,14 +20,17 @@ CONFIG_SPL_DRIVERS_MISC=y
 CONFIG_SPL=y
 CONFIG_IMX_BOOTAUX=y
 CONFIG_DISTRO_DEFAULTS=y
+CONFIG_REMAKE_ELF=y
 CONFIG_SYS_LOAD_ADDR=0x40480000
 CONFIG_FIT=y
 CONFIG_SPL_FIT_PRINT=y
 CONFIG_SPL_LOAD_FIT=y
 # CONFIG_USE_SPL_FIT_GENERATOR is not set
+CONFIG_OF_SYSTEM_SETUP=y
 CONFIG_BOARD_EARLY_INIT_F=y
 CONFIG_BOARD_LATE_INIT=y
 CONFIG_MISC_INIT_R=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
 CONFIG_SPL_I2C=y
 CONFIG_SPL_POWER=y
 CONFIG_SPL_WATCHDOG=y
diff --git a/configs/verdin-imx8mp_defconfig b/configs/verdin-imx8mp_defconfig
index 4c28f7f..e4e9efd 100644
--- a/configs/verdin-imx8mp_defconfig
+++ b/configs/verdin-imx8mp_defconfig
@@ -25,6 +25,7 @@ CONFIG_SPL=y
 CONFIG_IMX_BOOTAUX=y
 CONFIG_SPL_IMX_ROMAPI_LOADADDR=0x48000000
 CONFIG_DISTRO_DEFAULTS=y
+CONFIG_REMAKE_ELF=y
 CONFIG_SYS_LOAD_ADDR=0x43500000
 CONFIG_FIT=y
 CONFIG_FIT_EXTERNAL_OFFSET=0x3000
diff --git a/include/configs/imx8mn_var_som.h b/include/configs/imx8mn_var_som.h
index 1e800f0..f25d893 100644
--- a/include/configs/imx8mn_var_som.h
+++ b/include/configs/imx8mn_var_som.h
@@ -14,8 +14,6 @@
 
 #define CONFIG_SPL_MAX_SIZE		(148 * SZ_1K)
 #define CONFIG_SYS_MONITOR_LEN		SZ_512K
-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR		0x300
 #define CONFIG_SYS_UBOOT_BASE	\
 	(QSPI0_AMBA_BASE + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512)
 
@@ -84,7 +82,4 @@
 /* USDHC */
 #define CONFIG_SYS_FSL_ESDHC_ADDR	0
 
-/* I2C */
-#define CONFIG_SYS_I2C_SPEED		400000
-
 #endif /* __IMX8MN_VAR_SOM_H */
diff --git a/include/configs/imx8mp_rsb3720.h b/include/configs/imx8mp_rsb3720.h
index ac4a7d0..b899775 100644
--- a/include/configs/imx8mp_rsb3720.h
+++ b/include/configs/imx8mp_rsb3720.h
@@ -18,11 +18,9 @@
 
 #define CONFIG_SPL_MAX_SIZE		(152 * 1024)
 #define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
-#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
 #define CONFIG_SYS_UBOOT_BASE	(QSPI0_AMBA_BASE + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512)
 
 #ifdef CONFIG_SPL_BUILD
-#define CONFIG_SPL_LDSCRIPT		"arch/arm/cpu/armv8/u-boot-spl.lds"
 #define CONFIG_SPL_STACK		0x960000
 #define CONFIG_SPL_BSS_START_ADDR	0x0098FC00
 #define CONFIG_SPL_BSS_MAX_SIZE		0x400	/* 1 KB */
@@ -37,26 +35,11 @@
 #define CONFIG_SPL_ABORT_ON_RAW_IMAGE
 
 #if defined(CONFIG_NAND_BOOT)
-#define CONFIG_SPL_NAND_SUPPORT
-#define CONFIG_SPL_DMA
 #define CONFIG_SPL_NAND_MXS
-#define CONFIG_SPL_NAND_BASE
-#define CONFIG_SPL_NAND_IDENT
-#define CONFIG_SYS_NAND_U_BOOT_OFFS	0x4000000 /* Put the FIT out of \
-						   * first 64MB boot area \
-						   */
-
-/* Set a redundant offset in nand FIT mtdpart. The new uuu will burn full
- * boot image (not only FIT part) to the mtdpart, so we check both two offsets
- */
-#define CONFIG_SYS_NAND_U_BOOT_OFFS_REDUND \
-	(CONFIG_SYS_NAND_U_BOOT_OFFS + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512 - 0x8400)
-
 #endif
 
 #endif
 
-#define CONFIG_REMAKE_ELF
 /* ENET Config */
 /* ENET1 */
 #if defined(CONFIG_CMD_NET)
@@ -186,15 +169,12 @@
 #define CONFIG_MXC_UART_BASE		UART3_BASE_ADDR
 
 /* Monitor Command Prompt */
-#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
 #define CONFIG_SYS_CBSIZE		2048
 #define CONFIG_SYS_MAXARGS		64
 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
 					sizeof(CONFIG_SYS_PROMPT) + 16)
 
-#define CONFIG_IMX_BOOTAUX
-
 #define CONFIG_SYS_FSL_USDHC_NUM	2
 #define CONFIG_SYS_FSL_ESDHC_ADDR	0
 
@@ -213,11 +193,6 @@
 /* NAND stuff */
 #define CONFIG_SYS_MAX_NAND_DEVICE     1
 #define CONFIG_SYS_NAND_BASE           0x20000000
-#define CONFIG_SYS_NAND_5_ADDR_CYCLE
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-#define CONFIG_SYS_NAND_USE_FLASH_BBT
 #endif /* CONFIG_NAND_MXS */
 
-#define CONFIG_SYS_I2C_SPEED		100000
-
 #endif /* __IMX8MP_RSB3720_H */
diff --git a/include/configs/j721s2_evm.h b/include/configs/j721s2_evm.h
index 6fd098c..8788464 100644
--- a/include/configs/j721s2_evm.h
+++ b/include/configs/j721s2_evm.h
@@ -60,9 +60,6 @@
 #define CONFIG_SYS_BOOTM_LEN		SZ_64M
 #define CONFIG_CQSPI_REF_CLK		133333333
 
-/* HyperFlash related configuration */
-#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 1
-
 /* U-Boot general configuration */
 #define EXTRA_ENV_J721S2_BOARD_SETTINGS					\
 	"default_device_tree=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0"	\
diff --git a/include/configs/kontron_pitx_imx8m.h b/include/configs/kontron_pitx_imx8m.h
index 0f96b90..2449a98 100644
--- a/include/configs/kontron_pitx_imx8m.h
+++ b/include/configs/kontron_pitx_imx8m.h
@@ -11,11 +11,8 @@
 
 #define CONFIG_SPL_MAX_SIZE		(124 * SZ_1K)
 #define CONFIG_SYS_MONITOR_LEN		(512 * SZ_1K)
-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	0x300
 
 #ifdef CONFIG_SPL_BUILD
-#define CONFIG_SPL_LDSCRIPT		"arch/arm/cpu/armv8/u-boot-spl.lds"
 #define CONFIG_SPL_STACK		0x187FF0
 #define CONFIG_SPL_BSS_START_ADDR       0x00180000
 #define CONFIG_SPL_BSS_MAX_SIZE         SZ_8K
@@ -33,8 +30,6 @@
 #define CONFIG_POWER_PFUZE100_I2C_ADDR  0x08
 #endif
 
-#define CONFIG_REMAKE_ELF
-
 /* ENET1 Config */
 #if defined(CONFIG_CMD_NET)
 #define CONFIG_ETHPRIME                 "FEC"
@@ -92,6 +87,4 @@
 #define CONFIG_SYS_FSL_USDHC_NUM	2
 #define CONFIG_SYS_FSL_ESDHC_ADDR       0
 
-#define CONFIG_OF_SYSTEM_SETUP
-
 #endif
diff --git a/include/configs/ten64.h b/include/configs/ten64.h
index 54e65f2..1a62ddf 100644
--- a/include/configs/ten64.h
+++ b/include/configs/ten64.h
@@ -9,7 +9,6 @@
 
 #include "ls1088a_common.h"
 
-#define CONFIG_SYS_CLK_FREQ		100000000
 #define COUNTER_FREQUENCY		25000000	/* 25MHz */
 
 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
diff --git a/include/configs/verdin-imx8mp.h b/include/configs/verdin-imx8mp.h
index f8b4bf2..766707d 100644
--- a/include/configs/verdin-imx8mp.h
+++ b/include/configs/verdin-imx8mp.h
@@ -16,7 +16,6 @@
 
 #ifdef CONFIG_SPL_BUILD
 /*#define CONFIG_ENABLE_DDR_TRAINING_DEBUG*/
-#define CONFIG_SPL_LDSCRIPT		"arch/arm/cpu/armv8/u-boot-spl.lds"
 #define CONFIG_SPL_STACK		0x960000
 #define CONFIG_SPL_BSS_START_ADDR	0x0098fc00
 #define CONFIG_SPL_BSS_MAX_SIZE		SZ_1K
@@ -31,11 +30,8 @@
 #define CONFIG_POWER_PCA9450
 
 #define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SPEED		100000
 #endif /* CONFIG_SPL_BUILD */
 
-#define CONFIG_REMAKE_ELF
-
 /* ENET Config */
 /* ENET1 */
 #if defined(CONFIG_CMD_NET)