imx: Extend PCL063 support for phyCORE-i.MX6ULL SOM

Extend PHYTEC phyBOARD-i.MX6UL for phyCORE-i.MX6UL SoM (PCL063)
with eMMC on SoM.

CPU:   Freescale i.MX6ULL rev1.0 792 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 38C
Reset cause: POR
Model: Phytec phyBOARD-i.MX6ULL-Segin SBC
Board: PHYTEC phyCORE-i.MX6ULL
DRAM:  256 MiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
In:    serial@02020000
Out:   serial@02020000
Err:   serial@02020000
Net:   FEC0

Working:
 - Eth0
 - i2C
 - MMC/SD
 - eMMC
 - UART (1 & 5)
 - USB (host & otg)

Signed-off-by: Parthiban Nallathambi <parthitce@gmail.com>

12 files changed, 384 insertions, 11 deletions

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index f01ff9f..24a409d 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -589,6 +589,7 @@ dtb-$(CONFIG_MX6UL) += \
 dtb-$(CONFIG_MX6ULL) += \
 	imx6ull-14x14-evk.dtb \
 	imx6ull-colibri.dtb \
+	imx6ull-phycore-segin.dtb \
 	imx6ull-dart-6ul.dtb
 
 dtb-$(CONFIG_ARCH_MX6) += \
diff --git a/arch/arm/dts/imx6ul-phycore-segin.dts b/arch/arm/dts/imx6ul-phycore-segin.dts
index a46012e..7d68bf8 100644
--- a/arch/arm/dts/imx6ul-phycore-segin.dts
+++ b/arch/arm/dts/imx6ul-phycore-segin.dts
@@ -16,7 +16,8 @@
 
 /dts-v1/;
 
-#include "imx6ul-pcl063.dtsi"
+#include "imx6ul.dtsi"
+#include "pcl063-common.dtsi"
 
 / {
 	model = "Phytec phyBOARD-i.MX6UL-Segin SBC";
@@ -24,6 +25,10 @@
 		     "fsl,imx6ul";
 };
 
+&gpmi {
+	status = "okay";
+};
+
 &i2c1 {
 	i2c_rtc: rtc@68 {
 		compatible = "microcrystal,rv4162";
diff --git a/arch/arm/dts/imx6ull-phycore-segin.dts b/arch/arm/dts/imx6ull-phycore-segin.dts
new file mode 100644
index 0000000..6df3ad2
--- /dev/null
+++ b/arch/arm/dts/imx6ull-phycore-segin.dts
@@ -0,0 +1,70 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2019 Parthiban Nallathambi <parthitce@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "imx6ull.dtsi"
+#include "pcl063-common.dtsi"
+
+/ {
+	model = "Phytec phyBOARD-i.MX6ULL-Segin SBC";
+	compatible = "phytec,phyboard-imx6ull-segin", "phytec,imx6ull-pcl063",
+		     "fsl,imx6ull";
+};
+
+&i2c1 {
+	i2c_rtc: rtc@68 {
+		compatible = "microcrystal,rv4162";
+		reg = <0x68>;
+		status = "okay";
+	};
+};
+
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usdhc2 {
+	status = "okay";
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_otg1_id>;
+	dr_mode = "otg";
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	status = "okay";
+};
+
+&usbotg2 {
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+
+	pinctrl_uart5: uart5grp {
+		fsl,pins = <
+			MX6UL_PAD_UART5_TX_DATA__UART5_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX	0x1b0b1
+			MX6UL_PAD_GPIO1_IO08__UART5_DCE_RTS	0x1b0b1
+			MX6UL_PAD_GPIO1_IO09__UART5_DCE_CTS	0x1b0b1
+		>;
+	};
+
+	pinctrl_usb_otg1_id: usbotg1idgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID    0x17059
+		>;
+	};
+
+};
diff --git a/arch/arm/dts/imx6ul-pcl063.dtsi b/arch/arm/dts/pcl063-common.dtsi
index 24a6a47..2b14b2d 100644
--- a/arch/arm/dts/imx6ul-pcl063.dtsi
+++ b/arch/arm/dts/pcl063-common.dtsi
@@ -7,10 +7,6 @@
  * Author: Christian Hemp <c.hemp@phytec.de>
  */
 
-/dts-v1/;
-
-#include "imx6ul.dtsi"
-
 / {
 	model = "Phytec phyCORE-i.MX6 Ultra Lite SOM";
 	compatible = "phytec,imx6ul-pcl063", "fsl,imx6ul";
@@ -47,7 +43,7 @@
 	pinctrl-0 = <&pinctrl_gpmi_nand>;
 	nand-on-flash-bbt;
 	fsl,no-blockmark-swap;
-	status = "okay";
+	status = "disabled";
 
 	#address-cells = <1>;
 	#size-cells = <1>;
@@ -99,6 +95,18 @@
 	status = "okay";
 };
 
+&usdhc2 {
+	u-boot,dm-spl;
+	u-boot,dm-pre-reloc;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	bus-width = <8>;
+	no-1-8-v;
+	non-removable;
+	keep-power-in-suspend;
+	status = "disabled";
+};
+
 &iomuxc {
 	pinctrl-names = "default";
 
@@ -170,4 +178,19 @@
 
 		>;
 	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x170f9
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x100f9
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x170f9
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x170f9
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x170f9
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x170f9
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x170f9
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x170f9
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x170f9
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x170f9
+		>;
+	};
 };
diff --git a/arch/arm/mach-imx/mx6/Kconfig b/arch/arm/mach-imx/mx6/Kconfig
index f513c4c..baccc0b 100644
--- a/arch/arm/mach-imx/mx6/Kconfig
+++ b/arch/arm/mach-imx/mx6/Kconfig
@@ -455,6 +455,18 @@ config TARGET_PCL063
 	select DM_THERMAL
 	select SUPPORT_SPL
 
+config TARGET_PCL063_ULL
+	bool "PHYTEC PCL063 (phyCORE-i.MX6ULL)"
+	select MX6ULL
+	select DM
+	select DM_ETH
+	select DM_GPIO
+	select DM_I2C
+	select DM_MMC
+	select DM_SERIAL
+	select DM_THERMAL
+	select SUPPORT_SPL
+
 config TARGET_SECOMX6
 	bool "secomx6 boards"
 
diff --git a/board/phytec/pcl063/Kconfig b/board/phytec/pcl063/Kconfig
index 977db70..58f72f2 100644
--- a/board/phytec/pcl063/Kconfig
+++ b/board/phytec/pcl063/Kconfig
@@ -10,3 +10,16 @@ config SYS_CONFIG_NAME
 	default "pcl063"
 
 endif
+
+if TARGET_PCL063_ULL
+
+config SYS_BOARD
+	default "pcl063"
+
+config SYS_VENDOR
+	default "phytec"
+
+config SYS_CONFIG_NAME
+	default "pcl063_ull"
+
+endif
diff --git a/board/phytec/pcl063/MAINTAINERS b/board/phytec/pcl063/MAINTAINERS
index 037f243..710b968 100644
--- a/board/phytec/pcl063/MAINTAINERS
+++ b/board/phytec/pcl063/MAINTAINERS
@@ -1,9 +1,14 @@
 PCL063 BOARD
 M:	Martyn Welch <martyn.welch@collabora.com>
+M:	Parthiban Nallathambi <parthitce@gmail.com>
 S:	Maintained
 F:	arch/arm/dts/imx6ul-pcl063.dtsi
 F:	arch/arm/dts/imx6ul-phycore-segin.dts
+F:	arch/arm/dts/imx6ull-phycore-segin.dts
+F:	arch/arm/dts/pcl063-common.dtsi
 F:	arch/arm/dts/imx6ull-u-boot.dtsi
 F:	board/phytec/pcl063/
 F:	configs/phycore_pcl063_defconfig
+F:	configs/phycore_pcl063_ull_defconfig
 F:	include/configs/pcl063.h
+F:	include/configs/pcl063_ull.h
diff --git a/board/phytec/pcl063/pcl063.c b/board/phytec/pcl063/pcl063.c
index 38b233d..17012df 100644
--- a/board/phytec/pcl063/pcl063.c
+++ b/board/phytec/pcl063/pcl063.c
@@ -200,7 +200,10 @@ int board_init(void)
 
 int checkboard(void)
 {
-	puts("Board: PHYTEC phyCORE-i.MX6UL\n");
+	u32 cpurev = get_cpu_rev();
+
+	printf("Board: PHYTEC phyCORE-i.MX%s\n",
+	      get_imx_type((cpurev & 0xFF000) >> 12));
 
 	return 0;
 }
diff --git a/board/phytec/pcl063/spl.c b/board/phytec/pcl063/spl.c
index b93cd49..73a7746 100644
--- a/board/phytec/pcl063/spl.c
+++ b/board/phytec/pcl063/spl.c
@@ -13,6 +13,7 @@
 #include <asm/arch/mx6-ddr.h>
 #include <asm/arch/mx6-pins.h>
 #include <asm/arch/crm_regs.h>
+#include <asm/arch/sys_proto.h>
 #include <fsl_esdhc.h>
 
 /* Configuration for Micron MT41K256M16TW-107 IT:P, 32M x 16 x 8 -> 256MiB */
@@ -117,11 +118,32 @@ static iomux_v3_cfg_t const usdhc1_pads[] = {
 	MX6_PAD_UART1_RTS_B__USDHC1_CD_B | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 };
 
+#ifndef CONFIG_NAND_MXS
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+	MX6_PAD_NAND_RE_B__USDHC2_CLK    | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_WE_B__USDHC2_CMD    | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA00__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA01__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA02__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA03__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA04__USDHC2_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA05__USDHC2_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA06__USDHC2_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA07__USDHC2_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+#endif
+
 static struct fsl_esdhc_cfg usdhc_cfg[] = {
 	{
 		.esdhc_base = USDHC1_BASE_ADDR,
 		.max_bus_width = 4,
 	},
+#ifndef CONFIG_NAND_MXS
+	{
+		.esdhc_base = USDHC2_BASE_ADDR,
+		.max_bus_width = 8,
+	},
+#endif
 };
 
 int board_mmc_getcd(struct mmc *mmc)
@@ -131,12 +153,58 @@ int board_mmc_getcd(struct mmc *mmc)
 
 int board_mmc_init(bd_t *bis)
 {
-	imx_iomux_v3_setup_multiple_pads(usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
-	usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
-
-	return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
+	int i, ret;
+
+	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+		switch (i) {
+		case 0:
+			SETUP_IOMUX_PADS(usdhc1_pads);
+			usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+			break;
+#ifndef CONFIG_NAND_MXS
+		case 1:
+			SETUP_IOMUX_PADS(usdhc2_pads);
+			usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+			break;
+#endif
+		default:
+			printf("Warning - USDHC%d controller not supporting\n",
+			       i + 1);
+			return 0;
+		}
+
+		ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+		if (ret) {
+			printf("Warning: failed to initialize mmc dev %d\n", i);
+			return ret;
+		}
+	}
+
+	return 0;
 }
 
+void board_boot_order(u32 *spl_boot_list)
+{
+	u32 bmode = imx6_src_get_boot_mode();
+	u8 boot_dev = BOOT_DEVICE_MMC1;
+
+	switch ((bmode & IMX6_BMODE_MASK) >> IMX6_BMODE_SHIFT) {
+	case IMX6_BMODE_SD:
+	case IMX6_BMODE_ESD:
+		boot_dev = BOOT_DEVICE_MMC1;
+		break;
+	case IMX6_BMODE_MMC:
+	case IMX6_BMODE_EMMC:
+		boot_dev = BOOT_DEVICE_MMC2;
+		break;
+	default:
+		/* Default - BOOT_DEVICE_MMC1 */
+		printf("Wrong board boot order\n");
+		break;
+	}
+
+	spl_boot_list[0] = boot_dev;
+}
 #endif /* CONFIG_FSL_ESDHC */
 
 void board_init_f(ulong dummy)
diff --git a/configs/phycore_pcl063_ull_defconfig b/configs/phycore_pcl063_ull_defconfig
new file mode 100644
index 0000000..75408a8
--- /dev/null
+++ b/configs/phycore_pcl063_ull_defconfig
@@ -0,0 +1,54 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_SYS_TEXT_BASE=0x87800000
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_TARGET_PCL063_ULL=y
+CONFIG_SPL_MMC_SUPPORT=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SPL=y
+# CONFIG_CMD_DEKBLOB is not set
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_NR_DRAM_BANKS=8
+CONFIG_FIT=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
+CONFIG_BOOTDELAY=3
+# CONFIG_USE_BOOTCOMMAND is not set
+CONFIG_BOARD_EARLY_INIT_F=y
+CONFIG_SPL_USB_HOST_SUPPORT=y
+CONFIG_SPL_WATCHDOG_SUPPORT=y
+CONFIG_CMD_DM=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+# CONFIG_RANDOM_UUID is not set
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_SDP=y
+CONFIG_CMD_CACHE=y
+# CONFIG_ISO_PARTITION is not set
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="imx6ull-phycore-segin"
+CONFIG_DM_I2C_GPIO=y
+CONFIG_SYS_I2C_MXC=y
+CONFIG_FSL_ESDHC=y
+CONFIG_PHYLIB=y
+CONFIG_PHY_MICREL=y
+CONFIG_FEC_MXC=y
+CONFIG_MII=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX6=y
+CONFIG_DM_PMIC=y
+# CONFIG_SPL_PMIC_CHILDREN is not set
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_MXC_UART=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_MANUFACTURER="Phytec"
+CONFIG_USB_GADGET_VENDOR_NUM=0x01b67
+CONFIG_USB_GADGET_PRODUCT_NUM=0x4fff
+CONFIG_CI_UDC=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_LZO=y
diff --git a/include/configs/pcl063.h b/include/configs/pcl063.h
index 12d8d67..8fef250 100644
--- a/include/configs/pcl063.h
+++ b/include/configs/pcl063.h
@@ -22,6 +22,8 @@
  * Tweak the SPL text base address to avoid this.
  */
 
+#define CONFIG_SYS_FSL_USDHC_NUM	1
+
 /* Size of malloc() pool */
 #define CONFIG_SYS_MALLOC_LEN		(16 * SZ_1M)
 
diff --git a/include/configs/pcl063_ull.h b/include/configs/pcl063_ull.h
new file mode 100644
index 0000000..0f1a010
--- /dev/null
+++ b/include/configs/pcl063_ull.h
@@ -0,0 +1,117 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Board configuration file for Phytec phyBOARD-i.MX6ULL-Segin SBC
+ * Copyright (C) 2019 Parthiban Nallathambi <parthitce@gmail.com>
+ *
+ * Based on include/configs/xpress.h:
+ * Copyright (C) 2015-2016 Stefan Roese <sr@denx.de>
+ */
+#ifndef __PCL063_ULL_H
+#define __PCL063_ULL_H
+
+#include <linux/sizes.h>
+#include "mx6_common.h"
+
+/* SPL options */
+#include "imx6_spl.h"
+
+#define CONFIG_SYS_FSL_USDHC_NUM	2
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(16 * SZ_1M)
+
+/* Environment settings */
+#define CONFIG_ENV_SIZE			(0x4000)
+#define CONFIG_ENV_OFFSET		(0x80000)
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+#define CONFIG_ENV_OFFSET_REDUND	\
+	(CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+
+/* Environment in SD */
+#define CONFIG_SYS_MMC_ENV_DEV		0
+#define CONFIG_SYS_MMC_ENV_PART		0
+#define MMC_ROOTFS_DEV		0
+#define MMC_ROOTFS_PART		2
+
+/* Console configs */
+#define CONFIG_MXC_UART_BASE		UART1_BASE
+
+/* MMC Configs */
+#define CONFIG_FSL_USDHC
+
+#define CONFIG_SYS_FSL_ESDHC_ADDR	USDHC2_BASE_ADDR
+#define CONFIG_SUPPORT_EMMC_BOOT
+
+/* I2C configs */
+#ifdef CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
+#define CONFIG_SYS_I2C_SPEED		100000
+#endif
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_MEMTEST_START	0x80000000
+#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x10000000)
+
+#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
+#define CONFIG_SYS_HZ			1000
+
+/* Physical Memory Map */
+#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
+#define PHYS_SDRAM_SIZE			SZ_256M
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* NAND */
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_SYS_NAND_BASE		0x40000000
+
+/* USB Configs */
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_MXC_USB_PORTSC		(PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS		0
+#define CONFIG_USB_MAX_CONTROLLER_COUNT	1
+
+#define CONFIG_IMX_THERMAL
+
+#define ENV_MMC \
+	"mmcdev=" __stringify(MMC_ROOTFS_DEV) "\0" \
+	"mmcpart=" __stringify(MMC_ROOTFS_PART) "\0" \
+	"fitpart=1\0" \
+	"bootdelay=3\0" \
+	"silent=1\0" \
+	"optargs=rw rootwait\0" \
+	"mmcautodetect=yes\0" \
+	"mmcrootfstype=ext4\0" \
+	"mmcfit_name=fitImage\0" \
+	"mmcloadfit=fatload mmc ${mmcdev}:${fitpart} ${fit_addr} " \
+		    "${mmcfit_name}\0" \
+	"mmcargs=setenv bootargs " \
+		"root=/dev/mmcblk${mmcdev}p${mmcpart} ${optargs} " \
+		"console=${console} rootfstype=${mmcrootfstype}\0" \
+	"mmc_mmc_fit=run mmcloadfit;run mmcargs addcon; bootm ${fit_addr}\0" \
+
+/* Default environment */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"fdt_high=0xffffffff\0" \
+	"console=ttymxc0,115200n8\0" \
+	"addcon=setenv bootargs ${bootargs} console=${console},${baudrate}\0" \
+	"fit_addr=0x82000000\0" \
+	ENV_MMC
+
+#define CONFIG_BOOTCOMMAND		"run mmc_mmc_fit"
+
+#define BOOT_TARGET_DEVICES(func) \
+	func(MMC, mmc, 0) \
+	func(MMC, mmc, 1) \
+	func(DHCP, dhcp, na)
+
+#include <config_distro_bootcmd.h>
+
+#endif /* __PCL063_ULL_H */