Merge branch 'next' of https://gitlab.denx.de/u-boot/custodians/u-boot-riscv into next

27 files changed, 217 insertions, 1287 deletions

diff --git a/arch/arm/dts/imx8mm-venice-gw7901-u-boot.dtsi b/arch/arm/dts/imx8mm-venice-gw7901-u-boot.dtsi
index 11c773b..dc99e7b 100644
--- a/arch/arm/dts/imx8mm-venice-gw7901-u-boot.dtsi
+++ b/arch/arm/dts/imx8mm-venice-gw7901-u-boot.dtsi
@@ -129,6 +129,57 @@
 	phy-reset-post-delay = <1>;
 };
 
+&switch {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		lan1: port@0 {
+			phy-handle = <&sw_phy0>;
+		};
+
+		lan2: port@1 {
+			phy-handle = <&sw_phy1>;
+		};
+
+		lan3: port@2 {
+			phy-handle = <&sw_phy2>;
+		};
+
+		lan4: port@3 {
+			phy-handle = <&sw_phy3>;
+		};
+	};
+
+	mdios {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mdio@0 {
+			reg = <0>;
+			compatible = "microchip,ksz-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			sw_phy0: ethernet-phy@0 {
+				reg = <0x0>;
+			};
+
+			sw_phy1: ethernet-phy@1 {
+				reg = <0x1>;
+			};
+
+			sw_phy2: ethernet-phy@2 {
+				reg = <0x2>;
+			};
+
+			sw_phy3: ethernet-phy@3 {
+				reg = <0x3>;
+			};
+		};
+	};
+};
+
 &pinctrl_fec1 {
 	u-boot,dm-spl;
 };
diff --git a/arch/arm/dts/imx8mp-venice-gw74xx-u-boot.dtsi b/arch/arm/dts/imx8mp-venice-gw74xx-u-boot.dtsi
index 920246d..caf5d3a 100644
--- a/arch/arm/dts/imx8mp-venice-gw74xx-u-boot.dtsi
+++ b/arch/arm/dts/imx8mp-venice-gw74xx-u-boot.dtsi
@@ -162,6 +162,65 @@
 	u-boot,dm-spl;
 };
 
+&switch {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		lan1: port@0 {
+			phy-handle = <&sw_phy0>;
+		};
+
+		lan2: port@1 {
+			phy-handle = <&sw_phy1>;
+		};
+
+		lan3: port@2 {
+			phy-handle = <&sw_phy2>;
+		};
+
+		lan4: port@3 {
+			phy-handle = <&sw_phy3>;
+		};
+
+		lan5: port@4 {
+			phy-handle = <&sw_phy4>;
+		};
+	};
+
+	mdios {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mdio@0 {
+			reg = <0>;
+			compatible = "microchip,ksz-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			sw_phy0: ethernet-phy@0 {
+				reg = <0x0>;
+			};
+
+			sw_phy1: ethernet-phy@1 {
+				reg = <0x1>;
+			};
+
+			sw_phy2: ethernet-phy@2 {
+				reg = <0x2>;
+			};
+
+			sw_phy3: ethernet-phy@3 {
+				reg = <0x3>;
+			};
+
+			sw_phy4: ethernet-phy@4 {
+				reg = <0x4>;
+			};
+		};
+	};
+};
+
 &usdhc2 {
 	assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_400M>;
 	assigned-clock-rates = <400000000>;
diff --git a/arch/arm/include/asm/arch-imx8m/imx-regs.h b/arch/arm/include/asm/arch-imx8m/imx-regs.h
index ff3b9dd..29d5baa 100644
--- a/arch/arm/include/asm/arch-imx8m/imx-regs.h
+++ b/arch/arm/include/asm/arch-imx8m/imx-regs.h
@@ -27,6 +27,7 @@
 #define IOMUXC_GPR_BASE_ADDR	0x30340000
 #define OCOTP_BASE_ADDR		0x30350000
 #define ANATOP_BASE_ADDR	0x30360000
+#define SNVS_BASE_ADDR		0x30370000
 #define CCM_BASE_ADDR		0x30380000
 #define SRC_BASE_ADDR		0x30390000
 #define GPC_BASE_ADDR		0x303A0000
@@ -113,6 +114,10 @@
 #define SRC_DDR1_RCR_CORE_RESET_N_MASK	BIT(1)
 #define SRC_DDR1_RCR_PRESET_N_MASK	BIT(0)
 
+#define SNVS_LPSR			0x4c
+#define SNVS_LPLVDR			0x64
+#define SNVS_LPPGDR_INIT		0x41736166
+
 struct iomuxc_gpr_base_regs {
 	u32 gpr[47];
 };
diff --git a/arch/arm/mach-imx/imx8m/soc.c b/arch/arm/mach-imx/imx8m/soc.c
index 47c0a4f..a486328 100644
--- a/arch/arm/mach-imx/imx8m/soc.c
+++ b/arch/arm/mach-imx/imx8m/soc.c
@@ -544,6 +544,16 @@ static int imx8m_check_clock(void *ctx, struct event *event)
 }
 EVENT_SPY(EVT_DM_POST_INIT, imx8m_check_clock);
 
+static void imx8m_setup_snvs(void)
+{
+	/* Enable SNVS clock */
+	clock_enable(CCGR_SNVS, 1);
+	/* Initialize glitch detect */
+	writel(SNVS_LPPGDR_INIT, SNVS_BASE_ADDR + SNVS_LPLVDR);
+	/* Clear interrupt status */
+	writel(0xffffffff, SNVS_BASE_ADDR + SNVS_LPSR);
+}
+
 int arch_cpu_init(void)
 {
 	struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR;
@@ -594,6 +604,8 @@ int arch_cpu_init(void)
 			writel(0x200, &ocotp->ctrl_clr);
 	}
 
+	imx8m_setup_snvs();
+
 	return 0;
 }
 
diff --git a/arch/riscv/Kconfig b/arch/riscv/Kconfig
index 78e964d..32a90b8 100644
--- a/arch/riscv/Kconfig
+++ b/arch/riscv/Kconfig
@@ -269,6 +269,20 @@ config XIP
 	  from a NOR flash memory without copying the code to ram.
 	  Say yes here if U-Boot boots from flash directly.
 
+config SPL_XIP
+	bool "Enable XIP mode for SPL"
+	help
+	  If SPL starts in read-only memory (XIP for example) then we shouldn't
+	  rely on lock variables (for example hart_lottery and available_harts_lock),
+	  this affects only SPL, other stages should proceed as non-XIP.
+
+config AVAILABLE_HARTS
+	bool "Send IPI by available harts"
+	default y
+	help
+	  By default, IPI sending mechanism will depend on available_harts.
+	  If disable this, it will send IPI by CPUs node numbers of device tree.
+
 config SHOW_REGS
 	bool "Show registers on unhandled exception"
 
diff --git a/arch/riscv/cpu/cpu.c b/arch/riscv/cpu/cpu.c
index 3ffcbbd..52ab025 100644
--- a/arch/riscv/cpu/cpu.c
+++ b/arch/riscv/cpu/cpu.c
@@ -19,15 +19,17 @@
  * The variables here must be stored in the data section since they are used
  * before the bss section is available.
  */
-#ifndef CONFIG_XIP
+#if !CONFIG_IS_ENABLED(XIP)
 u32 hart_lottery __section(".data") = 0;
 
+#ifdef CONFIG_AVAILABLE_HARTS
 /*
  * The main hart running U-Boot has acquired available_harts_lock until it has
  * finished initialization of global data.
  */
 u32 available_harts_lock = 1;
 #endif
+#endif
 
 static inline bool supports_extension(char ext)
 {
diff --git a/arch/riscv/cpu/start.S b/arch/riscv/cpu/start.S
index b7f21ab..4687bca 100644
--- a/arch/riscv/cpu/start.S
+++ b/arch/riscv/cpu/start.S
@@ -122,7 +122,7 @@ call_board_init_f_0:
 call_harts_early_init:
 	jal	harts_early_init
 
-#ifndef CONFIG_XIP
+#if !CONFIG_IS_ENABLED(XIP)
 	/*
 	 * Pick hart to initialize global data and run U-Boot. The other harts
 	 * wait for initialization to complete.
@@ -152,22 +152,24 @@ call_harts_early_init:
 	/* save the boot hart id to global_data */
 	SREG	tp, GD_BOOT_HART(gp)
 
-#ifndef CONFIG_XIP
+#if !CONFIG_IS_ENABLED(XIP)
+#ifdef CONFIG_AVAILABLE_HARTS
 	la	t0, available_harts_lock
 	amoswap.w.rl zero, zero, 0(t0)
+#endif
 
 wait_for_gd_init:
-	la	t0, available_harts_lock
-	li	t1, 1
-1:	amoswap.w.aq t1, t1, 0(t0)
-	bnez	t1, 1b
-
 	/*
 	 * Set the global data pointer only when gd_t has been initialized.
 	 * This was already set by arch_setup_gd on the boot hart, but all other
 	 * harts' global data pointers gets set here.
 	 */
 	mv	gp, s0
+#ifdef CONFIG_AVAILABLE_HARTS
+	la	t0, available_harts_lock
+	li	t1, 1
+1:	amoswap.w.aq t1, t1, 0(t0)
+	bnez	t1, 1b
 
 	/* register available harts in the available_harts mask */
 	li	t1, 1
@@ -177,6 +179,7 @@ wait_for_gd_init:
 	SREG	t2, GD_AVAILABLE_HARTS(gp)
 
 	amoswap.w.rl zero, zero, 0(t0)
+#endif
 
 	/*
 	 * Continue on hart lottery winner, others branch to
diff --git a/arch/riscv/include/asm/global_data.h b/arch/riscv/include/asm/global_data.h
index 095484a..858594a 100644
--- a/arch/riscv/include/asm/global_data.h
+++ b/arch/riscv/include/asm/global_data.h
@@ -27,9 +27,11 @@ struct arch_global_data {
 #if CONFIG_IS_ENABLED(SMP)
 	struct ipi_data ipi[CONFIG_NR_CPUS];
 #endif
-#ifndef CONFIG_XIP
+#if !CONFIG_IS_ENABLED(XIP)
+#ifdef CONFIG_AVAILABLE_HARTS
 	ulong available_harts;
 #endif
+#endif
 };
 
 #include <asm-generic/global_data.h>
diff --git a/arch/riscv/lib/asm-offsets.c b/arch/riscv/lib/asm-offsets.c
index f1fe089..452dfce 100644
--- a/arch/riscv/lib/asm-offsets.c
+++ b/arch/riscv/lib/asm-offsets.c
@@ -16,9 +16,11 @@ int main(void)
 {
 	DEFINE(GD_BOOT_HART, offsetof(gd_t, arch.boot_hart));
 	DEFINE(GD_FIRMWARE_FDT_ADDR, offsetof(gd_t, arch.firmware_fdt_addr));
-#ifndef CONFIG_XIP
+#if !CONFIG_IS_ENABLED(XIP)
+#ifdef CONFIG_AVAILABLE_HARTS
 	DEFINE(GD_AVAILABLE_HARTS, offsetof(gd_t, arch.available_harts));
 #endif
+#endif
 
 	return 0;
 }
diff --git a/arch/riscv/lib/smp.c b/arch/riscv/lib/smp.c
index ba99210..c0f65af 100644
--- a/arch/riscv/lib/smp.c
+++ b/arch/riscv/lib/smp.c
@@ -45,11 +45,13 @@ static int send_ipi_many(struct ipi_data *ipi, int wait)
 			continue;
 		}
 
-#ifndef CONFIG_XIP
+#if !CONFIG_IS_ENABLED(XIP)
+#ifdef CONFIG_AVAILABLE_HARTS
 		/* skip if hart is not available */
 		if (!(gd->arch.available_harts & (1 << reg)))
 			continue;
 #endif
+#endif
 
 		gd->arch.ipi[reg].addr = ipi->addr;
 		gd->arch.ipi[reg].arg0 = ipi->arg0;
diff --git a/board/data_modul/imx8mm_edm_sbc/imx8mm_data_modul_edm_sbc.c b/board/data_modul/imx8mm_edm_sbc/imx8mm_data_modul_edm_sbc.c
index 6dc4e6a..dc08830 100644
--- a/board/data_modul/imx8mm_edm_sbc/imx8mm_data_modul_edm_sbc.c
+++ b/board/data_modul/imx8mm_edm_sbc/imx8mm_data_modul_edm_sbc.c
@@ -34,22 +34,6 @@ int board_phys_sdram_size(phys_size_t *size)
 	return 0;
 }
 
-/* IMX8M SNVS registers needed for the bootcount functionality */
-#define SNVS_BASE_ADDR			0x30370000
-#define SNVS_LPSR			0x4c
-#define SNVS_LPLVDR			0x64
-#define SNVS_LPPGDR_INIT		0x41736166
-
-static void setup_snvs(void)
-{
-	/* Enable SNVS clock */
-	clock_enable(CCGR_SNVS, 1);
-	/* Initialize glitch detect */
-	writel(SNVS_LPPGDR_INIT, SNVS_BASE_ADDR + SNVS_LPLVDR);
-	/* Clear interrupt status */
-	writel(0xffffffff, SNVS_BASE_ADDR + SNVS_LPSR);
-}
-
 static void setup_mac_address(void)
 {
 	unsigned char enetaddr[6];
@@ -99,7 +83,6 @@ static void setup_boot_device(void)
 
 int board_init(void)
 {
-	setup_snvs();
 	return 0;
 }
 
diff --git a/board/dhelectronics/dh_imx8mp/imx8mp_dhcom_pdk2.c b/board/dhelectronics/dh_imx8mp/imx8mp_dhcom_pdk2.c
index 6f06daf..9d8e19d 100644
--- a/board/dhelectronics/dh_imx8mp/imx8mp_dhcom_pdk2.c
+++ b/board/dhelectronics/dh_imx8mp/imx8mp_dhcom_pdk2.c
@@ -37,22 +37,6 @@ int board_phys_sdram_size(phys_size_t *size)
 	return 0;
 }
 
-/* IMX8M SNVS registers needed for the bootcount functionality */
-#define SNVS_BASE_ADDR			0x30370000
-#define SNVS_LPSR			0x4c
-#define SNVS_LPLVDR			0x64
-#define SNVS_LPPGDR_INIT		0x41736166
-
-static void setup_snvs(void)
-{
-	/* Enable SNVS clock */
-	clock_enable(CCGR_SNVS, 1);
-	/* Initialize glitch detect */
-	writel(SNVS_LPPGDR_INIT, SNVS_BASE_ADDR + SNVS_LPLVDR);
-	/* Clear interrupt status */
-	writel(0xffffffff, SNVS_BASE_ADDR + SNVS_LPSR);
-}
-
 static void setup_eqos(void)
 {
 	struct iomuxc_gpr_base_regs *gpr =
@@ -145,7 +129,6 @@ int board_init(void)
 {
 	setup_eqos();
 	setup_fec();
-	setup_snvs();
 	return 0;
 }
 
diff --git a/board/menlo/mx8menlo/mx8menlo.c b/board/menlo/mx8menlo/mx8menlo.c
index 9d3708a..61fc4ec 100644
--- a/board/menlo/mx8menlo/mx8menlo.c
+++ b/board/menlo/mx8menlo/mx8menlo.c
@@ -12,24 +12,7 @@
 #include <asm/mach-imx/iomux-v3.h>
 #include <spl.h>
 
-#define SNVS_BASE_ADDR		0x30370000
-#define SNVS_LPSR		0x4c
-#define SNVS_LPLVDR		0x64
-#define SNVS_LPPGDR_INIT	0x41736166
-
-static void setup_snvs(void)
-{
-	/* Enable SNVS clock */
-	clock_enable(CCGR_SNVS, 1);
-	/* Initialize glitch detect */
-	writel(SNVS_LPPGDR_INIT, SNVS_BASE_ADDR + SNVS_LPLVDR);
-	/* Clear interrupt status */
-	writel(0xffffffff, SNVS_BASE_ADDR + SNVS_LPSR);
-}
-
 void board_early_init(void)
 {
 	init_uart_clk(1);
-
-	setup_snvs();
 }
diff --git a/cmd/fdt.c b/cmd/fdt.c
index 842e6cb..6fbd920 100644
--- a/cmd/fdt.c
+++ b/cmd/fdt.c
@@ -48,11 +48,27 @@ void set_working_fdt_addr(ulong addr)
 /*
  * Get a value from the fdt and format it to be set in the environment
  */
-static int fdt_value_env_set(const void *nodep, int len, const char *var)
+static int fdt_value_env_set(const void *nodep, int len,
+			     const char *var, int index)
 {
-	if (is_printable_string(nodep, len))
-		env_set(var, (void *)nodep);
-	else if (len == 4) {
+	if (is_printable_string(nodep, len)) {
+		const char *nodec = (const char *)nodep;
+		int i;
+
+		/*
+		 * Iterate over all members in stringlist and find the one at
+		 * offset $index. If no such index exists, indicate failure.
+		 */
+		for (i = 0; i < len; i += strlen(nodec) + 1) {
+			if (index-- > 0)
+				continue;
+
+			env_set(var, nodec + i);
+			return 0;
+		}
+
+		return 1;
+	} else if (len == 4) {
 		char buf[11];
 
 		sprintf(buf, "0x%08X", fdt32_to_cpu(*(fdt32_t *)nodep));
@@ -426,10 +442,14 @@ static int do_fdt(struct cmd_tbl *cmdtp, int flag, int argc, char *const argv[])
 				return 0;
 			} else if (nodep && len > 0) {
 				if (subcmd[0] == 'v') {
+					int index = 0;
 					int ret;
 
+					if (argc == 7)
+						index = simple_strtoul(argv[6], NULL, 10);
+
 					ret = fdt_value_env_set(nodep, len,
-								var);
+								var, index);
 					if (ret != 0)
 						return ret;
 				} else if (subcmd[0] == 'a') {
@@ -1085,7 +1105,9 @@ static char fdt_help_text[] =
 	"fdt resize [<extrasize>]            - Resize fdt to size + padding to 4k addr + some optional <extrasize> if needed\n"
 	"fdt print  <path> [<prop>]          - Recursive print starting at <path>\n"
 	"fdt list   <path> [<prop>]          - Print one level starting at <path>\n"
-	"fdt get value <var> <path> <prop>   - Get <property> and store in <var>\n"
+	"fdt get value <var> <path> <prop> [<index>] - Get <property> and store in <var>\n"
+	"                                      In case of stringlist property, use optional <index>\n"
+	"                                      to select string within the stringlist. Default is 0.\n"
 	"fdt get name <var> <path> <index>   - Get name of node <index> and store in <var>\n"
 	"fdt get addr <var> <path> <prop>    - Get start address of <property> and store in <var>\n"
 	"fdt get size <var> <path> [<prop>]  - Get size of [<property>] or num nodes and store in <var>\n"
diff --git a/configs/ae350_rv32_spl_defconfig b/configs/ae350_rv32_spl_defconfig
index 9b79cc4..1cc98a2 100644
--- a/configs/ae350_rv32_spl_defconfig
+++ b/configs/ae350_rv32_spl_defconfig
@@ -48,3 +48,4 @@ CONFIG_SYS_NS16550=y
 CONFIG_SPI=y
 CONFIG_ATCSPI200_SPI=y
 # CONFIG_BINMAN_FDT is not set
+# CONFIG_AVAILABLE_HARTS is not set
diff --git a/configs/ae350_rv32_spl_xip_defconfig b/configs/ae350_rv32_spl_xip_defconfig
index c7b6ea4..67c1e35 100644
--- a/configs/ae350_rv32_spl_xip_defconfig
+++ b/configs/ae350_rv32_spl_xip_defconfig
@@ -11,7 +11,7 @@ CONFIG_SPL=y
 CONFIG_SYS_LOAD_ADDR=0x100000
 CONFIG_TARGET_AX25_AE350=y
 CONFIG_RISCV_SMODE=y
-CONFIG_XIP=y
+CONFIG_SPL_XIP=y
 CONFIG_DISTRO_DEFAULTS=y
 CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
 CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xffff00
diff --git a/configs/ae350_rv64_spl_defconfig b/configs/ae350_rv64_spl_defconfig
index 4c33ca2..4318300 100644
--- a/configs/ae350_rv64_spl_defconfig
+++ b/configs/ae350_rv64_spl_defconfig
@@ -49,3 +49,4 @@ CONFIG_SYS_NS16550=y
 CONFIG_SPI=y
 CONFIG_ATCSPI200_SPI=y
 # CONFIG_BINMAN_FDT is not set
+# CONFIG_AVAILABLE_HARTS is not set
diff --git a/configs/ae350_rv64_spl_xip_defconfig b/configs/ae350_rv64_spl_xip_defconfig
index a197c97..baee9bf 100644
--- a/configs/ae350_rv64_spl_xip_defconfig
+++ b/configs/ae350_rv64_spl_xip_defconfig
@@ -12,7 +12,7 @@ CONFIG_SYS_LOAD_ADDR=0x100000
 CONFIG_TARGET_AX25_AE350=y
 CONFIG_ARCH_RV64I=y
 CONFIG_RISCV_SMODE=y
-CONFIG_XIP=y
+CONFIG_SPL_XIP=y
 CONFIG_DISTRO_DEFAULTS=y
 CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
 CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xfffe70
diff --git a/configs/kontron-sl-mx8mm_defconfig b/configs/kontron-sl-mx8mm_defconfig
index 5387f65..f8589b0 100644
--- a/configs/kontron-sl-mx8mm_defconfig
+++ b/configs/kontron-sl-mx8mm_defconfig
@@ -39,7 +39,6 @@ CONFIG_CUSTOM_SYS_SPL_MALLOC_ADDR=0x42200000
 CONFIG_SYS_SPL_MALLOC_SIZE=0x80000
 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x300
-# CONFIG_SPL_FIT_IMAGE_TINY is not set
 CONFIG_SPL_I2C=y
 CONFIG_SPL_DM_SPI_FLASH=y
 CONFIG_SPL_POWER=y
diff --git a/doc/imx/habv4/csf_examples/mx8m/csf.sh b/doc/imx/habv4/csf_examples/mx8m/csf.sh
index 6898513..7d267a7 100644
--- a/doc/imx/habv4/csf_examples/mx8m/csf.sh
+++ b/doc/imx/habv4/csf_examples/mx8m/csf.sh
@@ -40,7 +40,7 @@ dd if=csf_spl.bin of=flash.bin bs=1 seek=${spl_dd_offset} conv=notrunc
 # fitImage tree
 fit_block_base=$(printf "0x%x" $(( $(sed -n "/CONFIG_SYS_TEXT_BASE=/ s@.*=@@p" .config) - $(sed -n "/CONFIG_FIT_EXTERNAL_OFFSET=/ s@.*=@@p" .config) - 0x200 - 0x40)) )
 fit_block_offset=$(printf "0x%s" $(fdtget -t x u-boot.dtb /binman/imx-boot/uboot offset))
-fit_block_size=$(printf "0x%x" $(( ( $(fdtdump u-boot.itb 2>/dev/null | sed -n "/^...totalsize:/ s@.*\(0x[0-9a-f]\+\).*@\1@p") + 0x1000 - 0x1 ) & ~(0x1000 - 0x1) + 0x20 )) )
+fit_block_size=$(printf "0x%x" $(( ( ($(fdtdump u-boot.itb 2>/dev/null | sed -n "/^...totalsize:/ s@.*\(0x[0-9a-f]\+\).*@\1@p") + 0x1000 - 0x1 ) & ~(0x1000 - 0x1)) + 0x20 )) )
 sed -i "/Blocks = / s@.*@  Blocks = $fit_block_base $fit_block_offset $fit_block_size \"flash.bin\", \\\\@" csf_fit.tmp
 
 # U-Boot
diff --git a/drivers/serial/usbtty.h b/drivers/serial/usbtty.h
index 0d89fc0..e27aa36 100644
--- a/drivers/serial/usbtty.h
+++ b/drivers/serial/usbtty.h
@@ -13,8 +13,6 @@
 #include <usbdevice.h>
 #if defined(CONFIG_PPC)
 #include <usb/mpc8xx_udc.h>
-#elif defined(CONFIG_DW_UDC)
-#include <usb/designware_udc.h>
 #elif defined(CONFIG_CI_UDC)
 #include <usb/ci_udc.h>
 #endif
diff --git a/drivers/usb/Kconfig b/drivers/usb/Kconfig
index fd13cf3..3afb45d 100644
--- a/drivers/usb/Kconfig
+++ b/drivers/usb/Kconfig
@@ -48,7 +48,7 @@ config DM_USB
 	  automatically probed when found on the bus.
 
 config SPL_DM_USB
-	bool "Enable driver model for USB host most in SPL"
+	bool "Enable driver model for USB host mode in SPL"
 	depends on SPL_DM && DM_USB
 	default n if ARCH_MVEBU
 	default y
diff --git a/drivers/usb/gadget/Makefile b/drivers/usb/gadget/Makefile
index 306dd31..dd09ee0 100644
--- a/drivers/usb/gadget/Makefile
+++ b/drivers/usb/gadget/Makefile
@@ -42,6 +42,5 @@ else
 ifdef CONFIG_USB_DEVICE
 obj-y += core.o
 obj-y += ep0.o
-obj-$(CONFIG_DW_UDC) += designware_udc.o
 endif
 endif
diff --git a/drivers/usb/gadget/designware_udc.c b/drivers/usb/gadget/designware_udc.c
deleted file mode 100644
index 41a6e8c..0000000
--- a/drivers/usb/gadget/designware_udc.c
+++ /dev/null
@@ -1,1021 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Based on drivers/usb/gadget/omap1510_udc.c
- * TI OMAP1510 USB bus interface driver
- *
- * (C) Copyright 2009
- * Vipin Kumar, STMicroelectronics, vipin.kumar@st.com.
- */
-
-#include <common.h>
-#include <serial.h>
-#include <asm/io.h>
-#include <linux/delay.h>
-
-#include <env.h>
-#include <usbdevice.h>
-#include "ep0.h"
-#include <usb/designware_udc.h>
-#include <usb/udc.h>
-#include <asm/arch/hardware.h>
-
-#define UDC_INIT_MDELAY		80	/* Device settle delay */
-
-/* Some kind of debugging output... */
-#ifndef DEBUG_DWUSBTTY
-#define UDCDBG(str)
-#define UDCDBGA(fmt, args...)
-#else
-#define UDCDBG(str) serial_printf(str "\n")
-#define UDCDBGA(fmt, args...) serial_printf(fmt "\n", ##args)
-#endif
-
-static struct urb *ep0_urb;
-static struct usb_device_instance *udc_device;
-
-static struct plug_regs *const plug_regs_p =
-    (struct plug_regs * const)CONFIG_SYS_PLUG_BASE;
-static struct udc_regs *const udc_regs_p =
-    (struct udc_regs * const)CONFIG_SYS_USBD_BASE;
-static struct udc_endp_regs *const outep_regs_p =
-    &((struct udc_regs * const)CONFIG_SYS_USBD_BASE)->out_regs[0];
-static struct udc_endp_regs *const inep_regs_p =
-    &((struct udc_regs * const)CONFIG_SYS_USBD_BASE)->in_regs[0];
-
-/*
- * udc_state_transition - Write the next packet to TxFIFO.
- * @initial:	Initial state.
- * @final:	Final state.
- *
- * Helper function to implement device state changes. The device states and
- * the events that transition between them are:
- *
- *				STATE_ATTACHED
- *				||	/\
- *				\/	||
- *	DEVICE_HUB_CONFIGURED			DEVICE_HUB_RESET
- *				||	/\
- *				\/	||
- *				STATE_POWERED
- *				||	/\
- *				\/	||
- *	DEVICE_RESET				DEVICE_POWER_INTERRUPTION
- *				||	/\
- *				\/	||
- *				STATE_DEFAULT
- *				||	/\
- *				\/	||
- *	DEVICE_ADDRESS_ASSIGNED			DEVICE_RESET
- *				||	/\
- *				\/	||
- *				STATE_ADDRESSED
- *				||	/\
- *				\/	||
- *	DEVICE_CONFIGURED			DEVICE_DE_CONFIGURED
- *				||	/\
- *				\/	||
- *				STATE_CONFIGURED
- *
- * udc_state_transition transitions up (in the direction from STATE_ATTACHED
- * to STATE_CONFIGURED) from the specified initial state to the specified final
- * state, passing through each intermediate state on the way. If the initial
- * state is at or above (i.e. nearer to STATE_CONFIGURED) the final state, then
- * no state transitions will take place.
- *
- * udc_state_transition also transitions down (in the direction from
- * STATE_CONFIGURED to STATE_ATTACHED) from the specified initial state to the
- * specified final state, passing through each intermediate state on the way.
- * If the initial state is at or below (i.e. nearer to STATE_ATTACHED) the final
- * state, then no state transitions will take place.
- *
- * This function must only be called with interrupts disabled.
- */
-static void udc_state_transition(usb_device_state_t initial,
-				 usb_device_state_t final)
-{
-	if (initial < final) {
-		switch (initial) {
-		case STATE_ATTACHED:
-			usbd_device_event_irq(udc_device,
-					      DEVICE_HUB_CONFIGURED, 0);
-			if (final == STATE_POWERED)
-				break;
-		case STATE_POWERED:
-			usbd_device_event_irq(udc_device, DEVICE_RESET, 0);
-			if (final == STATE_DEFAULT)
-				break;
-		case STATE_DEFAULT:
-			usbd_device_event_irq(udc_device,
-					      DEVICE_ADDRESS_ASSIGNED, 0);
-			if (final == STATE_ADDRESSED)
-				break;
-		case STATE_ADDRESSED:
-			usbd_device_event_irq(udc_device, DEVICE_CONFIGURED, 0);
-		case STATE_CONFIGURED:
-			break;
-		default:
-			break;
-		}
-	} else if (initial > final) {
-		switch (initial) {
-		case STATE_CONFIGURED:
-			usbd_device_event_irq(udc_device,
-					      DEVICE_DE_CONFIGURED, 0);
-			if (final == STATE_ADDRESSED)
-				break;
-		case STATE_ADDRESSED:
-			usbd_device_event_irq(udc_device, DEVICE_RESET, 0);
-			if (final == STATE_DEFAULT)
-				break;
-		case STATE_DEFAULT:
-			usbd_device_event_irq(udc_device,
-					      DEVICE_POWER_INTERRUPTION, 0);
-			if (final == STATE_POWERED)
-				break;
-		case STATE_POWERED:
-			usbd_device_event_irq(udc_device, DEVICE_HUB_RESET, 0);
-		case STATE_ATTACHED:
-			break;
-		default:
-			break;
-		}
-	}
-}
-
-/* Stall endpoint */
-static void udc_stall_ep(u32 ep_num)
-{
-	writel(readl(&inep_regs_p[ep_num].endp_cntl) | ENDP_CNTL_STALL,
-	       &inep_regs_p[ep_num].endp_cntl);
-
-	writel(readl(&outep_regs_p[ep_num].endp_cntl) | ENDP_CNTL_STALL,
-	       &outep_regs_p[ep_num].endp_cntl);
-}
-
-static void *get_fifo(int ep_num, int in)
-{
-	u32 *fifo_ptr = (u32 *)CONFIG_SYS_FIFO_BASE;
-
-	switch (ep_num) {
-	case UDC_EP3:
-		fifo_ptr += readl(&inep_regs_p[1].endp_bsorfn);
-		/* break intentionally left out */
-
-	case UDC_EP1:
-		fifo_ptr += readl(&inep_regs_p[0].endp_bsorfn);
-		/* break intentionally left out */
-
-	case UDC_EP0:
-	default:
-		if (in) {
-			fifo_ptr +=
-			    readl(&outep_regs_p[2].endp_maxpacksize) >> 16;
-			/* break intentionally left out */
-		} else {
-			break;
-		}
-
-	case UDC_EP2:
-		fifo_ptr += readl(&outep_regs_p[0].endp_maxpacksize) >> 16;
-		/* break intentionally left out */
-	}
-
-	return (void *)fifo_ptr;
-}
-
-static int usbgetpckfromfifo(int epNum, u8 *bufp, u32 len)
-{
-	u8 *fifo_ptr = (u8 *)get_fifo(epNum, 0);
-	u32 i, nw, nb;
-	u32 *wrdp;
-	u8 *bytp;
-	u32 tmp[128];
-
-	if (readl(&udc_regs_p->dev_stat) & DEV_STAT_RXFIFO_EMPTY)
-		return -1;
-
-	nw = len / sizeof(u32);
-	nb = len % sizeof(u32);
-
-	/* use tmp buf if bufp is not word aligned */
-	if ((int)bufp & 0x3)
-		wrdp = (u32 *)&tmp[0];
-	else
-		wrdp = (u32 *)bufp;
-
-	for (i = 0; i < nw; i++) {
-		writel(readl(fifo_ptr), wrdp);
-		wrdp++;
-	}
-
-	bytp = (u8 *)wrdp;
-	for (i = 0; i < nb; i++) {
-		writeb(readb(fifo_ptr), bytp);
-		fifo_ptr++;
-		bytp++;
-	}
-	readl(&outep_regs_p[epNum].write_done);
-
-	/* copy back tmp buffer to bufp if bufp is not word aligned */
-	if ((int)bufp & 0x3)
-		memcpy(bufp, tmp, len);
-
-	return 0;
-}
-
-static void usbputpcktofifo(int epNum, u8 *bufp, u32 len)
-{
-	u32 i, nw, nb;
-	u32 *wrdp;
-	u8 *bytp;
-	u8 *fifo_ptr = get_fifo(epNum, 1);
-
-	nw = len / sizeof(int);
-	nb = len % sizeof(int);
-	wrdp = (u32 *)bufp;
-	for (i = 0; i < nw; i++) {
-		writel(*wrdp, fifo_ptr);
-		wrdp++;
-	}
-
-	bytp = (u8 *)wrdp;
-	for (i = 0; i < nb; i++) {
-		writeb(*bytp, fifo_ptr);
-		fifo_ptr++;
-		bytp++;
-	}
-}
-
-/*
- * dw_write_noniso_tx_fifo - Write the next packet to TxFIFO.
- * @endpoint:		Endpoint pointer.
- *
- * If the endpoint has an active tx_urb, then the next packet of data from the
- * URB is written to the tx FIFO.  The total amount of data in the urb is given
- * by urb->actual_length.  The maximum amount of data that can be sent in any
- * one packet is given by endpoint->tx_packetSize.  The number of data bytes
- * from this URB that have already been transmitted is given by endpoint->sent.
- * endpoint->last is updated by this routine with the number of data bytes
- * transmitted in this packet.
- *
- */
-static void dw_write_noniso_tx_fifo(struct usb_endpoint_instance
-				       *endpoint)
-{
-	struct urb *urb = endpoint->tx_urb;
-	int align;
-
-	if (urb) {
-		u32 last;
-
-		UDCDBGA("urb->buffer %p, buffer_length %d, actual_length %d",
-			urb->buffer, urb->buffer_length, urb->actual_length);
-
-		last = min_t(u32, urb->actual_length - endpoint->sent,
-			     endpoint->tx_packetSize);
-
-		if (last) {
-			u8 *cp = urb->buffer + endpoint->sent;
-
-			/*
-			 * This ensures that USBD packet fifo is accessed
-			 * - through word aligned pointer or
-			 * - through non word aligned pointer but only
-			 *   with a max length to make the next packet
-			 *   word aligned
-			 */
-
-			align = ((ulong)cp % sizeof(int));
-			if (align)
-				last = min(last, sizeof(int) - align);
-
-			UDCDBGA("endpoint->sent %d, tx_packetSize %d, last %d",
-				endpoint->sent, endpoint->tx_packetSize, last);
-
-			usbputpcktofifo(endpoint->endpoint_address &
-					USB_ENDPOINT_NUMBER_MASK, cp, last);
-		}
-		endpoint->last = last;
-	}
-}
-
-/*
- * Handle SETUP USB interrupt.
- * This function implements TRM Figure 14-14.
- */
-static void dw_udc_setup(struct usb_endpoint_instance *endpoint)
-{
-	u8 *datap = (u8 *)&ep0_urb->device_request;
-	int ep_addr = endpoint->endpoint_address;
-
-	UDCDBG("-> Entering device setup");
-	usbgetpckfromfifo(ep_addr, datap, 8);
-
-	/* Try to process setup packet */
-	if (ep0_recv_setup(ep0_urb)) {
-		/* Not a setup packet, stall next EP0 transaction */
-		udc_stall_ep(0);
-		UDCDBG("can't parse setup packet, still waiting for setup");
-		return;
-	}
-
-	/* Check direction */
-	if ((ep0_urb->device_request.bmRequestType & USB_REQ_DIRECTION_MASK)
-	    == USB_REQ_HOST2DEVICE) {
-		UDCDBG("control write on EP0");
-		if (le16_to_cpu(ep0_urb->device_request.wLength)) {
-			/* Stall this request */
-			UDCDBG("Stalling unsupported EP0 control write data "
-			       "stage.");
-			udc_stall_ep(0);
-		}
-	} else {
-
-		UDCDBG("control read on EP0");
-		/*
-		 * The ep0_recv_setup function has already placed our response
-		 * packet data in ep0_urb->buffer and the packet length in
-		 * ep0_urb->actual_length.
-		 */
-		endpoint->tx_urb = ep0_urb;
-		endpoint->sent = 0;
-		/*
-		 * Write packet data to the FIFO.  dw_write_noniso_tx_fifo
-		 * will update endpoint->last with the number of bytes written
-		 * to the FIFO.
-		 */
-		dw_write_noniso_tx_fifo(endpoint);
-
-		writel(0x0, &inep_regs_p[ep_addr].write_done);
-	}
-
-	udc_unset_nak(endpoint->endpoint_address);
-
-	UDCDBG("<- Leaving device setup");
-}
-
-/*
- * Handle endpoint 0 RX interrupt
- */
-static void dw_udc_ep0_rx(struct usb_endpoint_instance *endpoint)
-{
-	u8 dummy[64];
-
-	UDCDBG("RX on EP0");
-
-	/* Check direction */
-	if ((ep0_urb->device_request.bmRequestType
-	     & USB_REQ_DIRECTION_MASK) == USB_REQ_HOST2DEVICE) {
-		/*
-		 * This rx interrupt must be for a control write data
-		 * stage packet.
-		 *
-		 * We don't support control write data stages.
-		 * We should never end up here.
-		 */
-
-		UDCDBG("Stalling unexpected EP0 control write "
-		       "data stage packet");
-		udc_stall_ep(0);
-	} else {
-		/*
-		 * This rx interrupt must be for a control read status
-		 * stage packet.
-		 */
-		UDCDBG("ACK on EP0 control read status stage packet");
-		u32 len = (readl(&outep_regs_p[0].endp_status) >> 11) & 0xfff;
-		usbgetpckfromfifo(0, dummy, len);
-	}
-}
-
-/*
- * Handle endpoint 0 TX interrupt
- */
-static void dw_udc_ep0_tx(struct usb_endpoint_instance *endpoint)
-{
-	struct usb_device_request *request = &ep0_urb->device_request;
-	int ep_addr;
-
-	UDCDBG("TX on EP0");
-
-	/* Check direction */
-	if ((request->bmRequestType & USB_REQ_DIRECTION_MASK) ==
-	    USB_REQ_HOST2DEVICE) {
-		/*
-		 * This tx interrupt must be for a control write status
-		 * stage packet.
-		 */
-		UDCDBG("ACK on EP0 control write status stage packet");
-	} else {
-		/*
-		 * This tx interrupt must be for a control read data
-		 * stage packet.
-		 */
-		int wLength = le16_to_cpu(request->wLength);
-
-		/*
-		 * Update our count of bytes sent so far in this
-		 * transfer.
-		 */
-		endpoint->sent += endpoint->last;
-
-		/*
-		 * We are finished with this transfer if we have sent
-		 * all of the bytes in our tx urb (urb->actual_length)
-		 * unless we need a zero-length terminating packet.  We
-		 * need a zero-length terminating packet if we returned
-		 * fewer bytes than were requested (wLength) by the host,
-		 * and the number of bytes we returned is an exact
-		 * multiple of the packet size endpoint->tx_packetSize.
-		 */
-		if ((endpoint->sent == ep0_urb->actual_length) &&
-		    ((ep0_urb->actual_length == wLength) ||
-		     (endpoint->last != endpoint->tx_packetSize))) {
-			/* Done with control read data stage. */
-			UDCDBG("control read data stage complete");
-		} else {
-			/*
-			 * We still have another packet of data to send
-			 * in this control read data stage or else we
-			 * need a zero-length terminating packet.
-			 */
-			UDCDBG("ACK control read data stage packet");
-			dw_write_noniso_tx_fifo(endpoint);
-
-			ep_addr = endpoint->endpoint_address;
-			writel(0x0, &inep_regs_p[ep_addr].write_done);
-		}
-	}
-}
-
-static struct usb_endpoint_instance *dw_find_ep(int ep)
-{
-	int i;
-
-	for (i = 0; i < udc_device->bus->max_endpoints; i++) {
-		if ((udc_device->bus->endpoint_array[i].endpoint_address &
-		     USB_ENDPOINT_NUMBER_MASK) == ep)
-			return &udc_device->bus->endpoint_array[i];
-	}
-	return NULL;
-}
-
-/*
- * Handle RX transaction on non-ISO endpoint.
- * The ep argument is a physical endpoint number for a non-ISO IN endpoint
- * in the range 1 to 15.
- */
-static void dw_udc_epn_rx(int ep)
-{
-	int nbytes = 0;
-	struct urb *urb;
-	struct usb_endpoint_instance *endpoint = dw_find_ep(ep);
-
-	if (endpoint) {
-		urb = endpoint->rcv_urb;
-
-		if (urb) {
-			u8 *cp = urb->buffer + urb->actual_length;
-
-			nbytes = (readl(&outep_regs_p[ep].endp_status) >> 11) &
-			    0xfff;
-			usbgetpckfromfifo(ep, cp, nbytes);
-			usbd_rcv_complete(endpoint, nbytes, 0);
-		}
-	}
-}
-
-/*
- * Handle TX transaction on non-ISO endpoint.
- * The ep argument is a physical endpoint number for a non-ISO IN endpoint
- * in the range 16 to 30.
- */
-static void dw_udc_epn_tx(int ep)
-{
-	struct usb_endpoint_instance *endpoint = dw_find_ep(ep);
-
-	if (!endpoint)
-		return;
-
-	/*
-	 * We need to transmit a terminating zero-length packet now if
-	 * we have sent all of the data in this URB and the transfer
-	 * size was an exact multiple of the packet size.
-	 */
-	if (endpoint->tx_urb &&
-	    (endpoint->last == endpoint->tx_packetSize) &&
-	    (endpoint->tx_urb->actual_length - endpoint->sent -
-	     endpoint->last == 0)) {
-		/* handle zero length packet here */
-		writel(0x0, &inep_regs_p[ep].write_done);
-
-	}
-
-	if (endpoint->tx_urb && endpoint->tx_urb->actual_length) {
-		/* retire the data that was just sent */
-		usbd_tx_complete(endpoint);
-		/*
-		 * Check to see if we have more data ready to transmit
-		 * now.
-		 */
-		if (endpoint->tx_urb && endpoint->tx_urb->actual_length) {
-			/* write data to FIFO */
-			dw_write_noniso_tx_fifo(endpoint);
-			writel(0x0, &inep_regs_p[ep].write_done);
-
-		} else if (endpoint->tx_urb
-			   && (endpoint->tx_urb->actual_length == 0)) {
-			/* udc_set_nak(ep); */
-		}
-	}
-}
-
-/*
- * Start of public functions.
- */
-
-/* Called to start packet transmission. */
-int udc_endpoint_write(struct usb_endpoint_instance *endpoint)
-{
-	udc_unset_nak(endpoint->endpoint_address & USB_ENDPOINT_NUMBER_MASK);
-	return 0;
-}
-
-/* Start to initialize h/w stuff */
-int udc_init(void)
-{
-	int i;
-	u32 plug_st;
-
-	udc_device = NULL;
-
-	UDCDBG("starting");
-
-	readl(&plug_regs_p->plug_pending);
-
-	for (i = 0; i < UDC_INIT_MDELAY; i++)
-		udelay(1000);
-
-	plug_st = readl(&plug_regs_p->plug_state);
-	writel(plug_st | PLUG_STATUS_EN, &plug_regs_p->plug_state);
-
-	writel(~0x0, &udc_regs_p->endp_int);
-	writel(~0x0, &udc_regs_p->dev_int_mask);
-	writel(~0x0, &udc_regs_p->endp_int_mask);
-
-#ifndef CONFIG_USBD_HS
-	writel(DEV_CONF_FS_SPEED | DEV_CONF_REMWAKEUP | DEV_CONF_SELFPOW |
-	       DEV_CONF_PHYINT_16, &udc_regs_p->dev_conf);
-#else
-	writel(DEV_CONF_HS_SPEED | DEV_CONF_REMWAKEUP | DEV_CONF_SELFPOW |
-			DEV_CONF_PHYINT_16, &udc_regs_p->dev_conf);
-#endif
-
-	writel(DEV_CNTL_SOFTDISCONNECT, &udc_regs_p->dev_cntl);
-
-	/* Clear all interrupts pending */
-	writel(DEV_INT_MSK, &udc_regs_p->dev_int);
-
-	return 0;
-}
-
-int is_usbd_high_speed(void)
-{
-	return (readl(&udc_regs_p->dev_stat) & DEV_STAT_ENUM) ? 0 : 1;
-}
-
-/*
- * udc_setup_ep - setup endpoint
- * Associate a physical endpoint with endpoint_instance
- */
-void udc_setup_ep(struct usb_device_instance *device,
-		  u32 ep, struct usb_endpoint_instance *endpoint)
-{
-	UDCDBGA("setting up endpoint addr %x", endpoint->endpoint_address);
-	int ep_addr;
-	int ep_num, ep_type;
-	int packet_size;
-	int buffer_size;
-	int attributes;
-	char *tt;
-	u32 endp_intmask;
-
-	if ((ep != 0) && (udc_device->device_state < STATE_ADDRESSED))
-		return;
-
-	tt = env_get("usbtty");
-	if (!tt)
-		tt = "generic";
-
-	ep_addr = endpoint->endpoint_address;
-	ep_num = ep_addr & USB_ENDPOINT_NUMBER_MASK;
-
-	if ((ep_addr & USB_ENDPOINT_DIR_MASK) == USB_DIR_IN) {
-		/* IN endpoint */
-		packet_size = endpoint->tx_packetSize;
-		buffer_size = packet_size * 2;
-		attributes = endpoint->tx_attributes;
-	} else {
-		/* OUT endpoint */
-		packet_size = endpoint->rcv_packetSize;
-		buffer_size = packet_size * 2;
-		attributes = endpoint->rcv_attributes;
-	}
-
-	switch (attributes & USB_ENDPOINT_XFERTYPE_MASK) {
-	case USB_ENDPOINT_XFER_CONTROL:
-		ep_type = ENDP_EPTYPE_CNTL;
-		break;
-	case USB_ENDPOINT_XFER_BULK:
-	default:
-		ep_type = ENDP_EPTYPE_BULK;
-		break;
-	case USB_ENDPOINT_XFER_INT:
-		ep_type = ENDP_EPTYPE_INT;
-		break;
-	case USB_ENDPOINT_XFER_ISOC:
-		ep_type = ENDP_EPTYPE_ISO;
-		break;
-	}
-
-	struct udc_endp_regs *out_p = &outep_regs_p[ep_num];
-	struct udc_endp_regs *in_p = &inep_regs_p[ep_num];
-
-	if (!ep_addr) {
-		/* Setup endpoint 0 */
-		buffer_size = packet_size;
-
-		writel(readl(&in_p->endp_cntl) | ENDP_CNTL_CNAK,
-		       &in_p->endp_cntl);
-
-		writel(readl(&out_p->endp_cntl) | ENDP_CNTL_CNAK,
-		       &out_p->endp_cntl);
-
-		writel(ENDP_CNTL_CONTROL | ENDP_CNTL_FLUSH, &in_p->endp_cntl);
-
-		writel(buffer_size / sizeof(int), &in_p->endp_bsorfn);
-
-		writel(packet_size, &in_p->endp_maxpacksize);
-
-		writel(ENDP_CNTL_CONTROL | ENDP_CNTL_RRDY, &out_p->endp_cntl);
-
-		writel(packet_size | ((buffer_size / sizeof(int)) << 16),
-		       &out_p->endp_maxpacksize);
-
-	} else if ((ep_addr & USB_ENDPOINT_DIR_MASK) == USB_DIR_IN) {
-		/* Setup the IN endpoint */
-		writel(0x0, &in_p->endp_status);
-		writel((ep_type << 4) | ENDP_CNTL_RRDY, &in_p->endp_cntl);
-		writel(buffer_size / sizeof(int), &in_p->endp_bsorfn);
-		writel(packet_size, &in_p->endp_maxpacksize);
-
-		if (!strcmp(tt, "cdc_acm")) {
-			if (ep_type == ENDP_EPTYPE_INT) {
-				/* Conf no. 1 Interface no. 0 */
-				writel((packet_size << 19) |
-				       ENDP_EPDIR_IN | (1 << 7) |
-				       (0 << 11) | (ep_type << 5) | ep_num,
-				       &udc_regs_p->udc_endp_reg[ep_num]);
-			} else {
-				/* Conf no. 1 Interface no. 1 */
-				writel((packet_size << 19) |
-				       ENDP_EPDIR_IN | (1 << 7) |
-				       (1 << 11) | (ep_type << 5) | ep_num,
-				       &udc_regs_p->udc_endp_reg[ep_num]);
-			}
-		} else {
-			/* Conf no. 1 Interface no. 0 */
-			writel((packet_size << 19) |
-			       ENDP_EPDIR_IN | (1 << 7) |
-			       (0 << 11) | (ep_type << 5) | ep_num,
-			       &udc_regs_p->udc_endp_reg[ep_num]);
-		}
-
-	} else {
-		/* Setup the OUT endpoint */
-		writel(0x0, &out_p->endp_status);
-		writel((ep_type << 4) | ENDP_CNTL_RRDY, &out_p->endp_cntl);
-		writel(packet_size | ((buffer_size / sizeof(int)) << 16),
-		       &out_p->endp_maxpacksize);
-
-		if (!strcmp(tt, "cdc_acm")) {
-			writel((packet_size << 19) |
-			       ENDP_EPDIR_OUT | (1 << 7) |
-			       (1 << 11) | (ep_type << 5) | ep_num,
-			       &udc_regs_p->udc_endp_reg[ep_num]);
-		} else {
-			writel((packet_size << 19) |
-			       ENDP_EPDIR_OUT | (1 << 7) |
-			       (0 << 11) | (ep_type << 5) | ep_num,
-			       &udc_regs_p->udc_endp_reg[ep_num]);
-		}
-
-	}
-
-	endp_intmask = readl(&udc_regs_p->endp_int_mask);
-	endp_intmask &= ~((1 << ep_num) | 0x10000 << ep_num);
-	writel(endp_intmask, &udc_regs_p->endp_int_mask);
-}
-
-/* Turn on the USB connection by enabling the pullup resistor */
-void udc_connect(void)
-{
-	u32 plug_st, dev_cntl;
-
-	dev_cntl = readl(&udc_regs_p->dev_cntl);
-	dev_cntl |= DEV_CNTL_SOFTDISCONNECT;
-	writel(dev_cntl, &udc_regs_p->dev_cntl);
-
-	udelay(1000);
-
-	dev_cntl = readl(&udc_regs_p->dev_cntl);
-	dev_cntl &= ~DEV_CNTL_SOFTDISCONNECT;
-	writel(dev_cntl, &udc_regs_p->dev_cntl);
-
-	plug_st = readl(&plug_regs_p->plug_state);
-	plug_st &= ~(PLUG_STATUS_PHY_RESET | PLUG_STATUS_PHY_MODE);
-	writel(plug_st, &plug_regs_p->plug_state);
-}
-
-/* Turn off the USB connection by disabling the pullup resistor */
-void udc_disconnect(void)
-{
-	u32 plug_st;
-
-	writel(DEV_CNTL_SOFTDISCONNECT, &udc_regs_p->dev_cntl);
-
-	plug_st = readl(&plug_regs_p->plug_state);
-	plug_st |= (PLUG_STATUS_PHY_RESET | PLUG_STATUS_PHY_MODE);
-	writel(plug_st, &plug_regs_p->plug_state);
-}
-
-/* Switch on the UDC */
-void udc_enable(struct usb_device_instance *device)
-{
-	UDCDBGA("enable device %p, status %d", device, device->status);
-
-	/* Save the device structure pointer */
-	udc_device = device;
-
-	/* Setup ep0 urb */
-	if (!ep0_urb) {
-		ep0_urb =
-		    usbd_alloc_urb(udc_device, udc_device->bus->endpoint_array);
-	} else {
-		serial_printf("udc_enable: ep0_urb already allocated %p\n",
-			      ep0_urb);
-	}
-
-	writel(DEV_INT_SOF, &udc_regs_p->dev_int_mask);
-}
-
-/**
- * udc_startup - allow udc code to do any additional startup
- */
-void udc_startup_events(struct usb_device_instance *device)
-{
-	/* The DEVICE_INIT event puts the USB device in the state STATE_INIT. */
-	usbd_device_event_irq(device, DEVICE_INIT, 0);
-
-	/*
-	 * The DEVICE_CREATE event puts the USB device in the state
-	 * STATE_ATTACHED.
-	 */
-	usbd_device_event_irq(device, DEVICE_CREATE, 0);
-
-	/*
-	 * Some USB controller driver implementations signal
-	 * DEVICE_HUB_CONFIGURED and DEVICE_RESET events here.
-	 * DEVICE_HUB_CONFIGURED causes a transition to the state STATE_POWERED,
-	 * and DEVICE_RESET causes a transition to the state STATE_DEFAULT.
-	 * The DW USB client controller has the capability to detect when the
-	 * USB cable is connected to a powered USB bus, so we will defer the
-	 * DEVICE_HUB_CONFIGURED and DEVICE_RESET events until later.
-	 */
-
-	udc_enable(device);
-}
-
-/*
- * Plug detection interrupt handling
- */
-static void dw_udc_plug_irq(void)
-{
-	if (readl(&plug_regs_p->plug_state) & PLUG_STATUS_ATTACHED) {
-		/*
-		 * USB cable attached
-		 * Turn off PHY reset bit (PLUG detect).
-		 * Switch PHY opmode to normal operation (PLUG detect).
-		 */
-		udc_connect();
-		writel(DEV_INT_SOF, &udc_regs_p->dev_int_mask);
-
-		UDCDBG("device attached and powered");
-		udc_state_transition(udc_device->device_state, STATE_POWERED);
-	} else {
-		writel(~0x0, &udc_regs_p->dev_int_mask);
-
-		UDCDBG("device detached or unpowered");
-		udc_state_transition(udc_device->device_state, STATE_ATTACHED);
-	}
-}
-
-/*
- * Device interrupt handling
- */
-static void dw_udc_dev_irq(void)
-{
-	if (readl(&udc_regs_p->dev_int) & DEV_INT_USBRESET) {
-		writel(~0x0, &udc_regs_p->endp_int_mask);
-
-		writel(readl(&inep_regs_p[0].endp_cntl) | ENDP_CNTL_FLUSH,
-		       &inep_regs_p[0].endp_cntl);
-
-		writel(DEV_INT_USBRESET, &udc_regs_p->dev_int);
-
-		/*
-		 * This endpoint0 specific register can be programmed only
-		 * after the phy clock is initialized
-		 */
-		writel((EP0_MAX_PACKET_SIZE << 19) | ENDP_EPTYPE_CNTL,
-				&udc_regs_p->udc_endp_reg[0]);
-
-		UDCDBG("device reset in progess");
-		udc_state_transition(udc_device->device_state, STATE_DEFAULT);
-	}
-
-	/* Device Enumeration completed */
-	if (readl(&udc_regs_p->dev_int) & DEV_INT_ENUM) {
-		writel(DEV_INT_ENUM, &udc_regs_p->dev_int);
-
-		/* Endpoint interrupt enabled for Ctrl IN & Ctrl OUT */
-		writel(readl(&udc_regs_p->endp_int_mask) & ~0x10001,
-		       &udc_regs_p->endp_int_mask);
-
-		UDCDBG("default -> addressed");
-		udc_state_transition(udc_device->device_state, STATE_ADDRESSED);
-	}
-
-	/* The USB will be in SUSPEND in 3 ms */
-	if (readl(&udc_regs_p->dev_int) & DEV_INT_INACTIVE) {
-		writel(DEV_INT_INACTIVE, &udc_regs_p->dev_int);
-
-		UDCDBG("entering inactive state");
-		/* usbd_device_event_irq(udc_device, DEVICE_BUS_INACTIVE, 0); */
-	}
-
-	/* SetConfiguration command received */
-	if (readl(&udc_regs_p->dev_int) & DEV_INT_SETCFG) {
-		writel(DEV_INT_SETCFG, &udc_regs_p->dev_int);
-
-		UDCDBG("entering configured state");
-		udc_state_transition(udc_device->device_state,
-				     STATE_CONFIGURED);
-	}
-
-	/* SetInterface command received */
-	if (readl(&udc_regs_p->dev_int) & DEV_INT_SETINTF)
-		writel(DEV_INT_SETINTF, &udc_regs_p->dev_int);
-
-	/* USB Suspend detected on cable */
-	if (readl(&udc_regs_p->dev_int) & DEV_INT_SUSPUSB) {
-		writel(DEV_INT_SUSPUSB, &udc_regs_p->dev_int);
-
-		UDCDBG("entering suspended state");
-		usbd_device_event_irq(udc_device, DEVICE_BUS_INACTIVE, 0);
-	}
-
-	/* USB Start-Of-Frame detected on cable */
-	if (readl(&udc_regs_p->dev_int) & DEV_INT_SOF)
-		writel(DEV_INT_SOF, &udc_regs_p->dev_int);
-}
-
-/*
- * Endpoint interrupt handling
- */
-static void dw_udc_endpoint_irq(void)
-{
-	while (readl(&udc_regs_p->endp_int) & ENDP0_INT_CTRLOUT) {
-
-		writel(ENDP0_INT_CTRLOUT, &udc_regs_p->endp_int);
-
-		if ((readl(&outep_regs_p[0].endp_status) & ENDP_STATUS_OUTMSK)
-		    == ENDP_STATUS_OUT_SETUP) {
-			dw_udc_setup(udc_device->bus->endpoint_array + 0);
-			writel(ENDP_STATUS_OUT_SETUP,
-			       &outep_regs_p[0].endp_status);
-
-		} else if ((readl(&outep_regs_p[0].endp_status) &
-			    ENDP_STATUS_OUTMSK) == ENDP_STATUS_OUT_DATA) {
-			dw_udc_ep0_rx(udc_device->bus->endpoint_array + 0);
-			writel(ENDP_STATUS_OUT_DATA,
-			       &outep_regs_p[0].endp_status);
-
-		} else if ((readl(&outep_regs_p[0].endp_status) &
-			    ENDP_STATUS_OUTMSK) == ENDP_STATUS_OUT_NONE) {
-			/* NONE received */
-		}
-
-		writel(0x0, &outep_regs_p[0].endp_status);
-	}
-
-	if (readl(&udc_regs_p->endp_int) & ENDP0_INT_CTRLIN) {
-		dw_udc_ep0_tx(udc_device->bus->endpoint_array + 0);
-
-		writel(ENDP_STATUS_IN, &inep_regs_p[0].endp_status);
-		writel(ENDP0_INT_CTRLIN, &udc_regs_p->endp_int);
-	}
-
-	if (readl(&udc_regs_p->endp_int) & ENDP_INT_NONISOOUT_MSK) {
-		u32 epnum = 0;
-		u32 ep_int = readl(&udc_regs_p->endp_int) &
-		    ENDP_INT_NONISOOUT_MSK;
-
-		ep_int >>= 16;
-		while (0x0 == (ep_int & 0x1)) {
-			ep_int >>= 1;
-			epnum++;
-		}
-
-		writel((1 << 16) << epnum, &udc_regs_p->endp_int);
-
-		if ((readl(&outep_regs_p[epnum].endp_status) &
-		     ENDP_STATUS_OUTMSK) == ENDP_STATUS_OUT_DATA) {
-
-			dw_udc_epn_rx(epnum);
-			writel(ENDP_STATUS_OUT_DATA,
-			       &outep_regs_p[epnum].endp_status);
-		} else if ((readl(&outep_regs_p[epnum].endp_status) &
-			    ENDP_STATUS_OUTMSK) == ENDP_STATUS_OUT_NONE) {
-			writel(0x0, &outep_regs_p[epnum].endp_status);
-		}
-	}
-
-	if (readl(&udc_regs_p->endp_int) & ENDP_INT_NONISOIN_MSK) {
-		u32 epnum = 0;
-		u32 ep_int = readl(&udc_regs_p->endp_int) &
-		    ENDP_INT_NONISOIN_MSK;
-
-		while (0x0 == (ep_int & 0x1)) {
-			ep_int >>= 1;
-			epnum++;
-		}
-
-		if (readl(&inep_regs_p[epnum].endp_status) & ENDP_STATUS_IN) {
-			writel(ENDP_STATUS_IN,
-			       &outep_regs_p[epnum].endp_status);
-			dw_udc_epn_tx(epnum);
-
-			writel(ENDP_STATUS_IN,
-			       &outep_regs_p[epnum].endp_status);
-		}
-
-		writel((1 << epnum), &udc_regs_p->endp_int);
-	}
-}
-
-/*
- * UDC interrupts
- */
-void udc_irq(void)
-{
-	/*
-	 * Loop while we have interrupts.
-	 * If we don't do this, the input chain
-	 * polling delay is likely to miss
-	 * host requests.
-	 */
-	while (readl(&plug_regs_p->plug_pending))
-		dw_udc_plug_irq();
-
-	while (readl(&udc_regs_p->dev_int))
-		dw_udc_dev_irq();
-
-	if (readl(&udc_regs_p->endp_int))
-		dw_udc_endpoint_irq();
-}
-
-/* Flow control */
-void udc_set_nak(int epid)
-{
-	writel(readl(&inep_regs_p[epid].endp_cntl) | ENDP_CNTL_SNAK,
-	       &inep_regs_p[epid].endp_cntl);
-
-	writel(readl(&outep_regs_p[epid].endp_cntl) | ENDP_CNTL_SNAK,
-	       &outep_regs_p[epid].endp_cntl);
-}
-
-void udc_unset_nak(int epid)
-{
-	u32 val;
-
-	val = readl(&inep_regs_p[epid].endp_cntl);
-	val &= ~ENDP_CNTL_SNAK;
-	val |= ENDP_CNTL_CNAK;
-	writel(val, &inep_regs_p[epid].endp_cntl);
-
-	val = readl(&outep_regs_p[epid].endp_cntl);
-	val &= ~ENDP_CNTL_SNAK;
-	val |= ENDP_CNTL_CNAK;
-	writel(val, &outep_regs_p[epid].endp_cntl);
-}
diff --git a/include/usb/designware_udc.h b/include/usb/designware_udc.h
deleted file mode 100644
index f716f07..0000000
--- a/include/usb/designware_udc.h
+++ /dev/null
@@ -1,183 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2009
- * Vipin Kumar, STMicroelectronics, vipin.kumar@st.com.
- */
-
-#ifndef __DW_UDC_H
-#define __DW_UDC_H
-
-/*
- * Defines for  USBD
- *
- * The udc_ahb controller has three AHB slaves:
- *
- * 1.  THe UDC registers
- * 2.  The plug detect
- * 3.  The RX/TX FIFO
- */
-
-#define MAX_ENDPOINTS		16
-
-struct udc_endp_regs {
-	u32 endp_cntl;
-	u32 endp_status;
-	u32 endp_bsorfn;
-	u32 endp_maxpacksize;
-	u32 reserved_1;
-	u32 endp_desc_point;
-	u32 reserved_2;
-	u32 write_done;
-};
-
-/* Endpoint Control Register definitions */
-
-#define  ENDP_CNTL_STALL		0x00000001
-#define  ENDP_CNTL_FLUSH		0x00000002
-#define  ENDP_CNTL_SNOOP		0x00000004
-#define  ENDP_CNTL_POLL			0x00000008
-#define  ENDP_CNTL_CONTROL		0x00000000
-#define  ENDP_CNTL_ISO			0x00000010
-#define  ENDP_CNTL_BULK			0x00000020
-#define  ENDP_CNTL_INT			0x00000030
-#define  ENDP_CNTL_NAK			0x00000040
-#define  ENDP_CNTL_SNAK			0x00000080
-#define  ENDP_CNTL_CNAK			0x00000100
-#define  ENDP_CNTL_RRDY			0x00000200
-
-/* Endpoint Satus Register definitions */
-
-#define  ENDP_STATUS_PIDMSK		0x0000000f
-#define  ENDP_STATUS_OUTMSK		0x00000030
-#define  ENDP_STATUS_OUT_NONE		0x00000000
-#define  ENDP_STATUS_OUT_DATA		0x00000010
-#define  ENDP_STATUS_OUT_SETUP		0x00000020
-#define  ENDP_STATUS_IN			0x00000040
-#define  ENDP_STATUS_BUFFNAV		0x00000080
-#define  ENDP_STATUS_FATERR		0x00000100
-#define  ENDP_STATUS_HOSTBUSERR		0x00000200
-#define  ENDP_STATUS_TDC		0x00000400
-#define  ENDP_STATUS_RXPKTMSK		0x003ff800
-
-struct udc_regs {
-	struct udc_endp_regs in_regs[MAX_ENDPOINTS];
-	struct udc_endp_regs out_regs[MAX_ENDPOINTS];
-	u32 dev_conf;
-	u32 dev_cntl;
-	u32 dev_stat;
-	u32 dev_int;
-	u32 dev_int_mask;
-	u32 endp_int;
-	u32 endp_int_mask;
-	u32 reserved_3[0x39];
-	u32 reserved_4;		/* offset 0x500 */
-	u32 udc_endp_reg[MAX_ENDPOINTS];
-};
-
-/* Device Configuration Register definitions */
-
-#define  DEV_CONF_HS_SPEED		0x00000000
-#define  DEV_CONF_LS_SPEED		0x00000002
-#define  DEV_CONF_FS_SPEED		0x00000003
-#define  DEV_CONF_REMWAKEUP		0x00000004
-#define  DEV_CONF_SELFPOW		0x00000008
-#define  DEV_CONF_SYNCFRAME		0x00000010
-#define  DEV_CONF_PHYINT_8		0x00000020
-#define  DEV_CONF_PHYINT_16		0x00000000
-#define  DEV_CONF_UTMI_BIDIR		0x00000040
-#define  DEV_CONF_STATUS_STALL		0x00000080
-
-/* Device Control Register definitions */
-
-#define  DEV_CNTL_RESUME		0x00000001
-#define  DEV_CNTL_TFFLUSH		0x00000002
-#define  DEV_CNTL_RXDMAEN		0x00000004
-#define  DEV_CNTL_TXDMAEN		0x00000008
-#define  DEV_CNTL_DESCRUPD		0x00000010
-#define  DEV_CNTL_BIGEND		0x00000020
-#define  DEV_CNTL_BUFFILL		0x00000040
-#define  DEV_CNTL_TSHLDEN		0x00000080
-#define  DEV_CNTL_BURSTEN		0x00000100
-#define  DEV_CNTL_DMAMODE		0x00000200
-#define  DEV_CNTL_SOFTDISCONNECT	0x00000400
-#define  DEV_CNTL_SCALEDOWN		0x00000800
-#define  DEV_CNTL_BURSTLENU		0x00010000
-#define  DEV_CNTL_BURSTLENMSK		0x00ff0000
-#define  DEV_CNTL_TSHLDLENU		0x01000000
-#define  DEV_CNTL_TSHLDLENMSK		0xff000000
-
-/* Device Status Register definitions */
-
-#define  DEV_STAT_CFG			0x0000000f
-#define  DEV_STAT_INTF			0x000000f0
-#define  DEV_STAT_ALT			0x00000f00
-#define  DEV_STAT_SUSP			0x00001000
-#define  DEV_STAT_ENUM			0x00006000
-#define  DEV_STAT_ENUM_SPEED_HS		0x00000000
-#define  DEV_STAT_ENUM_SPEED_FS		0x00002000
-#define  DEV_STAT_ENUM_SPEED_LS		0x00004000
-#define  DEV_STAT_RXFIFO_EMPTY		0x00008000
-#define  DEV_STAT_PHY_ERR		0x00010000
-#define  DEV_STAT_TS			0xf0000000
-
-/* Device Interrupt Register definitions */
-
-#define  DEV_INT_MSK			0x0000007f
-#define  DEV_INT_SETCFG			0x00000001
-#define  DEV_INT_SETINTF		0x00000002
-#define  DEV_INT_INACTIVE		0x00000004
-#define  DEV_INT_USBRESET		0x00000008
-#define  DEV_INT_SUSPUSB		0x00000010
-#define  DEV_INT_SOF			0x00000020
-#define  DEV_INT_ENUM			0x00000040
-
-/* Endpoint Interrupt Register definitions */
-
-#define  ENDP0_INT_CTRLIN		0x00000001
-#define  ENDP1_INT_BULKIN		0x00000002
-#define  ENDP_INT_NONISOIN_MSK		0x0000AAAA
-#define  ENDP2_INT_BULKIN		0x00000004
-#define  ENDP0_INT_CTRLOUT		0x00010000
-#define  ENDP1_INT_BULKOUT		0x00020000
-#define  ENDP2_INT_BULKOUT		0x00040000
-#define  ENDP_INT_NONISOOUT_MSK		0x55540000
-
-/* Endpoint Register definitions */
-#define  ENDP_EPDIR_OUT			0x00000000
-#define  ENDP_EPDIR_IN			0x00000010
-#define  ENDP_EPTYPE_CNTL		0x0
-#define  ENDP_EPTYPE_ISO		0x1
-#define  ENDP_EPTYPE_BULK		0x2
-#define  ENDP_EPTYPE_INT		0x3
-
-/*
- * Defines for Plug Detect
- */
-
-struct plug_regs {
-	u32 plug_state;
-	u32 plug_pending;
-};
-
-/* Plug State Register definitions */
-#define  PLUG_STATUS_EN			0x1
-#define  PLUG_STATUS_ATTACHED		0x2
-#define  PLUG_STATUS_PHY_RESET		0x4
-#define  PLUG_STATUS_PHY_MODE		0x8
-
-/*
- * Defines for UDC FIFO (Slave Mode)
- */
-struct udcfifo_regs {
-	u32 *fifo_p;
-};
-
-/*
- * UDC endpoint definitions
- */
-#define  UDC_EP0			0
-#define  UDC_EP1			1
-#define  UDC_EP2			2
-#define  UDC_EP3			3
-
-#endif /* __DW_UDC_H */
diff --git a/tools/binman/bintool.py b/tools/binman/bintool.py
index 032179a..a582d9d 100644
--- a/tools/binman/bintool.py
+++ b/tools/binman/bintool.py
@@ -319,7 +319,7 @@ class Bintool:
             return result.stdout
 
     @classmethod
-    def build_from_git(cls, git_repo, make_target, bintool_path):
+    def build_from_git(cls, git_repo, make_target, bintool_path, flags=None):
         """Build a bintool from a git repo
 
         This clones the repo in a temporary directory, builds it with 'make',
@@ -330,6 +330,7 @@ class Bintool:
             make_target (str): Target to pass to 'make' to build the tool
             bintool_path (str): Relative path of the tool in the repo, after
                 build is complete
+            flags (list of str): Flags or variables to pass to make, or None
 
         Returns:
             tuple:
@@ -341,8 +342,11 @@ class Bintool:
         print(f"- clone git repo '{git_repo}' to '{tmpdir}'")
         tools.run('git', 'clone', '--depth', '1', git_repo, tmpdir)
         print(f"- build target '{make_target}'")
-        tools.run('make', '-C', tmpdir, '-j', f'{multiprocessing.cpu_count()}',
-                  make_target)
+        cmd = ['make', '-C', tmpdir, '-j', f'{multiprocessing.cpu_count()}',
+               make_target]
+        if flags:
+            cmd += flags
+        tools.run(*cmd)
         fname = os.path.join(tmpdir, bintool_path)
         if not os.path.exists(fname):
             print(f"- File '{fname}' was not produced")
diff --git a/tools/binman/btool/futility.py b/tools/binman/btool/futility.py
index 75a05c2..04c9aef 100644
--- a/tools/binman/btool/futility.py
+++ b/tools/binman/btool/futility.py
@@ -160,8 +160,17 @@ class Bintoolfutility(bintool.Bintool):
         Raises:
             Valuerror: Fetching could not be completed
         """
-        if method != bintool.FETCH_BIN:
+        if method != bintool.FETCH_BUILD:
             return None
-        fname, tmpdir = self.fetch_from_drive(
-            '1hdsInzsE4aJbmBeJ663kYgjOQyW1I-E0')
-        return fname, tmpdir
+
+        # The Chromium OS repo is here:
+        # https://chromium.googlesource.com/chromiumos/platform/vboot_reference/
+        #
+        # Unfortunately this requires logging in and obtaining a line for the
+        # .gitcookies file. So use a mirror instead.
+        result = self.build_from_git(
+            'https://github.com/sjg20/vboot_reference.git',
+            'all',
+            'build/futility/futility',
+            flags=['USE_FLASHROM=0'])
+        return result