Age | Commit message (Collapse) | Author | Files | Lines |
|
The CP0 control register set has never been defined, however encodings
for the CFC0 and CTC0 instructions remained available for implementers
up until the MIPS32 ISA declared them invalid and causing the Reserved
Instruction exception[1]. Therefore we handle them for both assembly
and disassembly, however in the latter case the names of CP0 registers
from the regular set are incorrectly printed if named registers are
requested. This is because we do not define separate operand classes
for coprocessor regular and control registers respectively, which means
the disassembler has no way to tell the two cases apart. Consequently
nonsensical disassembly is produced like:
cfc0 v0,c0_random
Later the MIPSr5 ISA reused the encodings for XPA ASE MFHC0 and MTHC0
instructions[2] although it failed to document them in the relevant
opcode table until MIPSr6 only.
Correct the issue then by defining a new register class, OP_REG_CONTROL,
and corresponding operand codes, `g' and `y' for the two positions in
the machine instruction a control register operand can take. Adjust the
test cases affected accordingly.
While at it swap the regular MIPS opcode table "cfc0" and "ctc0" entries
with each other so that they come in the alphabetical order.
References:
[1] "MIPS32 Architecture For Programmers, Volume II: The MIPS32
Instruction Set", MIPS Technologies, Inc., Document Number: MD00086,
Revision 1.00, August 29, 2002, Table A-9 "MIPS32 COP0 Encoding of
rs Field", p. 242
[2] "MIPS Architecture For Programmers, Volume II-A: The MIPS32
Instruction Set", MIPS Technologies, Inc., Document Number: MD00086,
Revision 5.04, December 11, 2013, Section 3.2 "Alphabetical List of
Instructions", pp. 195, 216
include/
* opcode/mips.h: Document `g' and `y' operand codes.
(mips_reg_operand_type): Add OP_REG_CONTROL enumeration
constant.
gas/
* tc-mips.c (convert_reg_type) <OP_REG_CONTROL>: New case.
(macro) <M_TRUNCWS, M_TRUNCWD>: Use the `g' rather than `G'
operand code.
opcodes/
* mips-dis.c (print_reg) <OP_REG_COPRO>: Move control register
handling code over to...
<OP_REG_CONTROL>: ... this new case.
* mips-opc.c (decode_mips_operand) <'g', 'y'>: New cases.
(mips_builtin_opcodes): Update "cfc1", "ctc1", "cttc1", "cttc2",
"cfc0", "ctc0", "cfc2", "ctc2", "cfc3", and "ctc3" entries
replacing the `G' operand code with `g'. Update "cftc1" and
"cftc2" entries replacing the `E' operand code with `y'.
* micromips-opc.c (decode_micromips_operand) <'g'>: New case.
(micromips_opcodes): Update "cfc1", "cfc2", "ctc1", and "ctc2"
entries replacing the `G' operand code with `g'.
binutils/
* testsuite/binutils-all/mips/mips-xpa-virt-1.d: Correct CFC0
operand disassembly.
* testsuite/binutils-all/mips/mips-xpa-virt-3.d: Likewise.
|
|
The DMTC1 instruction operates on a floating-point general register as
its second operand, however in the disassembly of the microMIPS encoding
a floating-point control register is shown instead. This is due to an
incorrect ordering of the two "dmtc1" entries in the opcode table, which
gives precedence to one using the `G' aka coprocessor format over one
using the `S' or floating-point register format.
The coprocessor format, or OP_REG_COPRO, is used so that GAS supports
referring to FPRs by their numbers in assembly, such as $0, $1, etc.
however in the case of CP1/FPU it is also used by the disassembler to
decode those numbers to the names of corresponding control registers.
This in turn causes nonsensical disassembly such as:
dmtc1 a1,c1_fir
in a reference to $f0. It has been like this ever since microMIPS ISA
support has been added.
Correct the ordering of the two entries then by swapping them with each
other, making disassembly output consistent with the regular MIPS DMTC1
instruction as well all the remaining CP1 move instructions. Adjust all
the test cases affected accordingly.
opcodes/
* micromips-opc.c (micromips_opcodes): Swap the two "dmtc1"
entries with each other.
gas/
* testsuite/gas/mips/micromips.d: Update disassembly according
to "dmtc1" entry fix with opcodes.
* testsuite/gas/mips/micromips-compact.d: Likewise.
* testsuite/gas/mips/micromips-insn32.d: Likewise.
* testsuite/gas/mips/micromips-noinsn32.d: Likewise.
* testsuite/gas/mips/micromips-trap.d: Likewise.
* testsuite/gas/mips/micromips@isa-override-1.d: Likewise.
|
|
cpu/
* frv.opc: Replace bfd_boolean with bool, FALSE with false, and
TRUE with true throughout.
opcodes/
* sysdep.h (POISON_BFD_BOOLEAN): Define.
* aarch64-asm-2.c, * aarch64-asm.c, * aarch64-asm.h,
* aarch64-dis-2.c, * aarch64-dis.c, * aarch64-dis.h,
* aarch64-gen.c, * aarch64-opc.c, * aarch64-opc.h, * arc-dis.c,
* arc-dis.h, * arc-fxi.h, * arc-opc.c, * arm-dis.c, * bfin-dis.c,
* cris-dis.c, * csky-dis.c, * csky-opc.h, * dis-buf.c,
* disassemble.c, * frv-opc.c, * frv-opc.h, * h8300-dis.c,
* i386-dis.c, * m68k-dis.c, * metag-dis.c, * microblaze-dis.c,
* microblaze-dis.h, * micromips-opc.c, * mips-dis.c,
* mips-formats.h, * mips-opc.c, * mips16-opc.c, * mmix-dis.c,
* msp430-dis.c, * nds32-dis.c, * nfp-dis.c, * nios2-dis.c,
* ppc-dis.c, * riscv-dis.c, * score-dis.c, * score7-dis.c,
* tic6x-dis.c, * v850-dis.c, * vax-dis.c, * wasm32-dis.c,
* xtensa-dis.c: Replace bfd_boolean with bool, FALSE with false,
and TRUE with true throughout.
|
|
|
|
|
|
|
|
|
|
Add support for the base and Virtualization ASE microMIPS instructions
as per the architecture specifications[1][2][3][4].
Most of this change by Andrew Bennett.
[1] "MIPS Architecture for Programmers Volume II-B: The microMIPS32
Instruction Set", MIPS Technologies, Inc., Document Number: MD00582,
Revision 5.04, January 15, 2014, Section 5.5 "Recoded 32-Bit
Instructions", p. 340
[2] "microMIPS32 Architecture for Programmers Volume IV-i:
Virtualization Module of the microMIPS32 Architecture", MIPS
Technologies, Inc., Document Number: MD00848, Revision 1.06,
December 10, 2013, Section 6.1 "Overview", pp. 133, 136
[3] "MIPS Architecture for Programmers Volume II-B: The microMIPS64
Instruction Set", MIPS Technologies, Inc., Document Number: MD00594,
Revision 5.04, January 15, 2014, Section 5.5 "Recoded 32-Bit
Instructions", pp. 415, 444
[4] "microMIPS64 Architecture for Programmers Volume IV-i:
Virtualization Module of the microMIPS64 Architecture", MIPS
Technologies, Inc., Document Number: MD00849, Revision 1.06,
December 10, 2013, Section 6.1 "Overview", pp. 134-135, 139-140
binutils/
* NEWS: Mention microMIPS XPA support.
opcodes/
* micromips-opc.c (XPA, XPAVZ): New macros.
(micromips_opcodes): Add "mfhc0", "mfhgc0", "mthc0" and
"mthgc0".
gas/
* config/tc-mips.c (mips_ases): Add microMIPS XPA support.
* testsuite/gas/mips/micromips@xpa.d: New test.
* testsuite/gas/mips/mips.exp: Run the new test. Enable
`xpa-virt-err' test for `micromips'.
|
|
Add base microMIPS Release 5 ISA support and the ERETNC instruction in
particular, as per the architecture specifications[1][2].
Most of this change by Andrew Bennett.
References:
[1] "MIPS Architecture for Programmers Volume II-B: The microMIPS32
Instruction Set", MIPS Technologies, Inc., Document Number: MD00582,
Revision 5.04, January 15, 2014, Section 5.5 "Recoded 32-Bit
Instructions", pp. 266-267
[2] "MIPS Architecture for Programmers Volume II-B: The microMIPS64
Instruction Set", MIPS Technologies, Inc., Document Number: MD00594,
Revision 5.04, January 15, 2014, Section 5.5 "Recoded 32-Bit
Instructions", pp. 326-327
binutils/
* NEWS: Mention microMIPS Release 5 ISA support.
opcodes/
* micromips-opc.c (I36): New macro.
(micromips_opcodes): Add "eretnc".
gas/
* testsuite/gas/mips/micromips@r5.d: New test.
* testsuite/gas/mips/mips.exp: Run the new test.
|
|
Following the way how descriptive SYNC mnemonics have been defined in
the architecture[1][2] mark them as aliases, so that the generic SYNC
instruction can be alternatively disassembled along with its immediate
operand, as noted in the documents referred.
References:
[1] "MIPS Architecture For Programmers, Volume II-A: The MIPS32
Instruction Set", MIPS Technologies, Inc., Document Number: MD00086,
Revision 5.04, December 11, 2013, Table 4.7 "Encodings of the
Bits[10:6] of the SYNC instruction; the SType Field", p. 305
[2] "MIPS Architecture for Programmers, Volume II-B: The microMIPS32
Instruction Set", MIPS Technologies, Inc., Document Number: MD00582,
Revision 5.04, January 15, 2014, Table 5.28 "Encodings of the
Bits[10:6] of the SYNC instruction; the SType Field", p. 481
opcodes/
* mips-opc.c (mips_builtin_opcodes): Mark "synciobdma", "syncs",
"syncw", "syncws", "sync_acquire", "sync_mb", "sync_release",
"sync_rmb" and "sync_wmb" as aliases.
* micromips-opc.c (micromips_opcodes): Mark "sync_acquire",
"sync_mb", "sync_release", "sync_rmb" and "sync_wmb" as aliases.
gas/
* testsuite/gas/mips/mips32r2-sync-1.d: New test.
* testsuite/gas/mips/micromips@mips32r2-sync-1.d: New test.
* testsuite/gas/mips/mips.exp: Run the new tests.
|
|
|
|
Convert microMIPS branches and jumps whose delay slot would be filled by
a generated NOP instruction to the corresponding compact form where one
exists, in a manner similar to MIPS16 JR->JRC and JALR->JALRC swap.
Do so even where the transformation switches from a 16-bit to a 32-bit
branch encoding for no benefit in code size reduction, as this is still
advantageous. This is because a branch/NOP pair takes 2 pipeline slots
or a 2-cycle completion latency except in superscalar implementations.
Whereas a compact branch may or may not stall on its target fetch, so it
will at most have a 2-cycle completion latency and may have only 1 even
in scalar implementations, and in superscalar implementations it is
expected to have no worse latency as a branch/NOP pair has. Also it
won't stall and therefore take the extra latency cycle in the not-taken
case.
Technically this is the same as MIPS16 compaction: for the qualifying
instruction encodings the APPEND_ADD_COMPACT machine code generation
method is selected where APPEND_ADD_WITH_NOP otherwise would and tells
the code generator in `append_insn' to convert the regular form of an
instruction to its corresponding compact form. For this the opcode is
tweaked as necessary and the microMIPS opcode table is scanned for the
matching updated instruction. A non-$0 `rt' operand to BEQ and BNE
instructions is moved to the `rs' operand field of BEQZC and BNEZC
encodings as required.
Unlike with MIPS16 compaction however we need to handle out-of-distance
branch relaxation as well. We do this by deferring the generation of
any delay-slot NOP required to relaxation made in `md_convert_frag', by
converting the APPEND_ADD_WITH_NOP machine code generation to APPEND_ADD
where a relaxed instruction is recorded. Relaxation then, depending on
actual code produced, chooses between either using a compact branch or
jump encoding and emitting the NOP outstanding if no compact encoding is
possible.
For code simplicity's sake the relaxation pass is retained even if the
principle of preferring a compact encoding to a 16-bit branch/NOP pair
means, in the absence of out-of-range branch relaxation, that a single
compact branch machine code instruction will eventually be produced from
a given assembly source instruction.
gas/
* config/tc-mips.c (RELAX_MICROMIPS_ENCODE): Add `nods' flag.
(RELAX_MICROMIPS_RELAX32, RELAX_MICROMIPS_TOOFAR16)
(RELAX_MICROMIPS_MARK_TOOFAR16, RELAX_MICROMIPS_CLEAR_TOOFAR16)
(RELAX_MICROMIPS_TOOFAR32, RELAX_MICROMIPS_MARK_TOOFAR32)
(RELAX_MICROMIPS_CLEAR_TOOFAR32): Shift bits.
(get_append_method): Also return APPEND_ADD_COMPACT for
microMIPS instructions.
(find_altered_mips16_opcode): Exclude macros from matching.
Factor code out...
(find_altered_opcode): ... to this new function.
(find_altered_micromips_opcode): New function.
(frag_branch_delay_slot_size): Likewise.
(append_insn): Handle microMIPS branch/jump compaction.
(macro_start): Likewise.
(relaxed_micromips_32bit_branch_length): Likewise.
(md_convert_frag): Likewise.
* testsuite/gas/mips/micromips.s: Add conditional explicit NOPs
for delay slot filling.
* testsuite/gas/mips/micromips-b16.s: Add explicit NOPs for
delay slot filling.
* testsuite/gas/mips/micromips-size-1.s: Likewise.
* testsuite/gas/mips/micromips.l: Adjust line numbers.
* testsuite/gas/mips/micromips-warn.l: Likewise.
* testsuite/gas/mips/micromips-size-1.l: Likewise.
* testsuite/gas/mips/micromips.d: Adjust padding.
* testsuite/gas/mips/micromips-trap.d: Likewise.
* testsuite/gas/mips/micromips-insn32.d: Likewise.
* testsuite/gas/mips/micromips-noinsn32.d: Likewise.
* testsuite/gas/mips/micromips@beq.d: Update patterns for
branch/jump compaction.
* testsuite/gas/mips/micromips@bge.d: Likewise.
* testsuite/gas/mips/micromips@bgeu.d: Likewise.
* testsuite/gas/mips/micromips@blt.d: Likewise.
* testsuite/gas/mips/micromips@bltu.d: Likewise.
* testsuite/gas/mips/micromips@branch-misc-4.d: Likewise.
* testsuite/gas/mips/micromips@branch-misc-4-64.d: Likewise.
* testsuite/gas/mips/micromips@branch-misc-5.d: Likewise.
* testsuite/gas/mips/micromips@branch-misc-5pic.d: Likewise.
* testsuite/gas/mips/micromips@branch-misc-5-64.d: Likewise.
* testsuite/gas/mips/micromips@branch-misc-5pic-64.d: Likewise.
* testsuite/gas/mips/micromips@jal-svr4pic-local.d: Likewise.
* testsuite/gas/mips/micromips@jal-svr4pic-local-n32.d:
Likewise.
* testsuite/gas/mips/micromips@jal-svr4pic-local-n64.d:
Likewise.
* testsuite/gas/mips/micromips@loc-swap.d: Likewise.
* testsuite/gas/mips/micromips@loc-swap-dis.d: Likewise.
* testsuite/gas/mips/micromips@relax.d: Likewise.
* testsuite/gas/mips/micromips@relax-at.d: Likewise.
* testsuite/gas/mips/micromips@relax-swap3.d: Likewise.
* testsuite/gas/mips/branch-extern-2.d: Likewise.
* testsuite/gas/mips/branch-extern-4.d: Likewise.
* testsuite/gas/mips/branch-section-2.d: Likewise.
* testsuite/gas/mips/branch-section-4.d: Likewise.
* testsuite/gas/mips/branch-weak-2.d: Likewise.
* testsuite/gas/mips/branch-weak-5.d: Likewise.
* testsuite/gas/mips/micromips-branch-absolute.d: Likewise.
* testsuite/gas/mips/micromips-branch-absolute-n32.d: Likewise.
* testsuite/gas/mips/micromips-branch-absolute-n64.d: Likewise.
* testsuite/gas/mips/micromips-branch-absolute-addend.d:
Likewise.
* testsuite/gas/mips/micromips-branch-absolute-addend-n32.d:
Likewise.
* testsuite/gas/mips/micromips-branch-absolute-addend-n64.d:
Likewise.
* testsuite/gas/mips/micromips-compact.d: New test.
* testsuite/gas/mips/mips.exp: Run the new test.
ld/
* testsuite/ld-mips-elf/micromips-branch-absolute.d: Update
patterns for branch compaction.
* testsuite/ld-mips-elf/micromips-branch-absolute-addend.d:
Likewise.
opcodes/
* micromips-opc.c (micromips_opcodes): Reorder "bc" next to "b",
"beqzc" next to "beq", "bnezc" next to "bne" and "jrc" next to
"j".
|
|
|
|
The MIPS assembly idiom 'move' now maps to the 'or' machine instruction. This
change affects microMIPS, MIPS32, MIPS64.
2015-08-12 Simon Dardis <simon.dardis@imgtec.com>
opcodes/
* micromips-opc.c (micromips_opcodes): Re-order table so that move
based on 'or' is first.
* mips-opc.c (mips_builtin_opcodes): Ditto.
bfd/
* elfxx-mips.c (STUB_MOVE): Change to use 'or' only.
(mips_o32_exec_plt0_entry, mips_n32_exec_plt0_entry,
mips_n64_exec_plt0_entry, micromips_insn32_o32_exec_plt0_entry):
Update to use 'or' instead of 'addu/daddu'.
(_bfd_mips_elf_finish_dynamic_symbol): Update usage of STUB_MOVE.
(move_insns_32): Reorder table.
gas/
* config/tc-mips.c (move_register): Change to use 'or' only.
(s_cpload, s_cpsetup, s_cprestore, s_cpreturn): Update to
use or for move.
gas/testsuite/
* gas/mips/elf-rel23.d: Update test.
* gas/mips/elf-rel23.d: Ditto.
* gas/mips/elf-rel23a.d: Ditto.
* gas/mips/elf-rel23b.d: Ditto.
* gas/mips/elf_e_flags1.d: Ditto.
* gas/mips/elf_e_flags2.d: Ditto.
* gas/mips/elf_e_flags3.d: Ditto.
* gas/mips/elf_e_flags4.d: Ditto.
* gas/mips/loc-swap-dis.d: Ditto.
* gas/mips/micromips-insn32.d: Ditto.
* gas/mips/micromips-noinsn32.d: Ditto.
* gas/mips/micromips-trap.d: Ditto.
* gas/mips/micromips.d: Ditto.
* gas/mips/mips-abi32-pic.d: Ditto.
* gas/mips/mips-abi32.d: Ditto.
* gas/mips/mips-gp32-fp32-pic.d: Ditto.
* gas/mips/mips-gp32-fp32.d: Ditto.
* gas/mips/mips-gp32-fp64-pic.d: Ditto.
* gas/mips/mips-gp32-fp64.d: Ditto.
* gas/mips/mips-gp64-fp32-pic.d: Ditto.
* gas/mips/mips-gp64-fp32.d: Ditto.
* gas/mips/mips-gp64-fp64-pic.d: Ditto.
* gas/mips/mips-gp64-fp64.d: Ditto.
* gas/mips/mipsr6@loc-swap-dis.d: Ditto.
* gas/mips/tls-o32.d: Ditto.
* gas/mips/uld2-eb.d: Ditto.
* gas/mips/uld2-el.d: Ditto.
* gas/mips/ulw2-eb-ilocks.d: Ditto.
* gas/mips/ulw2-eb.d: Ditto.
* gas/mips/ulw2-el-ilocks.d: Ditto.
* gas/mips/ulw2-el.d: Ditto.
* gas/mips/move.d: New test.
* gas/mips/move.s: Ditto.
* gas/mips/micromips32-move.d: Ditto.
* gas/mips/micromips32-move.s: Ditto.
* gas/mips/mips.exp: Run the new tests.
gold/
* mips.cc (plt0_entry_o32, plt0_entry_n32, plt0_entry_n64,
lazy_stub_normal_1, lazy_stub_normal_1_n64,
lazy_stub_normal_2, lazy_stub_normal_2_n64, lazy_stub_big,
lazy_stub_big_n64, lazy_stub_micromips32_normal_1_n64,
lazy_stub_micromips32_normal_2_n64, lazy_stub_micromips32_big,
lazy_stub_micromips32_big_n64): Update to use 'or' for move instead
of 'addu/daddu'.
ld/testsuite/
* ld-mips-elf/compressed-plt-1-n32-mips16.od: Update test.
* ld-mips-elf/compressed-plt-1-n32-umips.od: Ditto.
* ld-mips-elf/compressed-plt-1-o32-mips16-got.od: Ditto.
* ld-mips-elf/compressed-plt-1-o32-mips16-only.od: Ditto.
* ld-mips-elf/compressed-plt-1-o32-mips16-word.od: Ditto.
* ld-mips-elf/compressed-plt-1-o32-mips16.od: Ditto.
* ld-mips-elf/compressed-plt-1-o32-se.od: Ditto.
* ld-mips-elf/compressed-plt-1-o32-umips-got.od: Ditto.
* ld-mips-elf/compressed-plt-1-o32-umips-word.od: Ditto.
* ld-mips-elf/compressed-plt-1-o32-umips.od: Ditto.
* ld-mips-elf/jalx-2.dd: Ditto.
* ld-mips-elf/mips16-pic-3.dd: Ditto.
* ld-mips-elf/pic-and-nonpic-3a.dd: Ditto.
* ld-mips-elf/pic-and-nonpic-3b.dd: Ditto.
* ld-mips-elf/pic-and-nonpic-5b.dd: Ditto.
* ld-mips-elf/pic-and-nonpic-6-n32.dd: Ditto.
* ld-mips-elf/pic-and-nonpic-6-o32.dd: Ditto.
* ld-mips-elf/stub-dynsym-1-10000.d: Ditto.
* ld-mips-elf/stub-dynsym-1-2fe80.d: Ditto.
* ld-mips-elf/stub-dynsym-1-7fff.d: Ditto.
* ld-mips-elf/stub-dynsym-1-8000.d: Ditto.
* ld-mips-elf/stub-dynsym-1-fff0.d: Ditto.
* ld-mips-elf/tlsbin-o32.d: Ditto.
* ld-mips-elf/tlsdyn-o32-1.d: Ditto.
* ld-mips-elf/tlsdyn-o32-2.d: Ditto.
* ld-mips-elf/tlsdyn-o32-3.d: Ditto.
* ld-mips-elf/tlsdyn-o32.d: Ditto.
* ld-mips-elf/tlslib-o32.d: Ditto.
|
|
|
|
This change moves the microMIPS 10-bit uninterpreted immediate code
embedded at bits 25..16 in the SYSCALL, WAIT, SDBBP and HYPCALL
instructions from `B' over to `+J' which is the operand code used in
the standard MIPS instruction set for a similar code embedded at bits
20..11, currently used by HYPCALL only in that set.
opcodes/
* micromips-opc.c (decode_micromips_operand): Rename `B' to `+J'.
(micromips_opcodes): Use "+J" in place of "B" for "hypcall",
"sdbbp", "syscall" and "wait".
include/opcode/
* mips.h: Document the move of `MICROMIPSOP_*_CODE10' from `B'
over to `+J'.
|
|
The 48-bit LI instruction encoding has been removed from the microMIPS
ISA and no implementation ever made that included it.
* micromips-opc.c (micromips_opcodes): Remove #ifdef-ed out
48-bit "li" encoding.
|
|
gas/
* config/tc-mips.c: Rename INSN_LOAD_COPROC_DELAY to INSN_LOAD_COPROC
and INSN_COPROC_MOVE_DELAY to INSN_COPROC_MOVE throughout.
include/opcode/
* mips.h (INSN_LOAD_COPROC_DELAY): Rename to...
(INSN_LOAD_COPROC): New define.
(INSN_COPROC_MOVE_DELAY): Rename to...
(INSN_COPROC_MOVE): New define.
opcodes/
* micromips-opc.c (COD): Rename throughout to...
(CM): New define, update to use INSN_COPROC_MOVE.
(LCD): Rename throughout to...
(LC): New define, update to use INSN_LOAD_COPROC.
* mips-opc.c: Likewise.
|
|
Specification:
https://dmz-portal.mips.com/wiki/MIPS_O32_ABI_-_FR0_and_FR1_Interlinking
include/
* elf/mips.h (PT_MIPS_ABIFLAGS, SHT_MIPS_ABIFLAGS): Define.
(Val_GNU_MIPS_ABI_FP_OLD_64): Rename from Val_GNU_MIPS_ABI_FP_64.
(Val_GNU_MIPS_ABI_FP_64): Redefine.
(Val_GNU_MIPS_ABI_FP_XX): Define.
(Elf_External_ABIFlags_v0, Elf_Internal_ABIFlags_v0): New structures.
(AFL_REG_NONE, AFL_REG_32, AFL_REG_64, AFL_REG_128): Define.
(AFL_ASE_DSP, AFL_ASE_DSPR2, AFL_ASE_EVA, AFL_ASE_MCU): Likewise.
(AFL_ASE_MDMX, AFL_ASE_MIPS3D, AFL_ASE_MT, AFL_ASE_SMARTMIPS): Likewise.
(AFL_ASE_VIRT, AFL_ASE_MSA, AFL_ASE_MIPS16): Likewise.
(AFL_ASE_MICROMIPS, AFL_ASE_XPA): Likewise.
(AFL_EXT_XLR, AFL_EXT_OCTEON2, AFL_EXT_OCTEONP): Likewise.
(AFL_EXT_LOONGSON_3A, AFL_EXT_OCTEON, AFL_EXT_5900): Likewise.
(AFL_EXT_4650, AFL_EXT_4010, AFL_EXT_4100, AFL_EXT_3900): Likewise.
(AFL_EXT_10000, AFL_EXT_SB1, AFL_EXT_4111, AFL_EXT_4120): Likewise.
(AFL_EXT_5400, AFL_EXT_5500, AFL_EXT_LOONGSON_2E): Likewise.
(AFL_EXT_LOONGSON_2F): Likewise.
(bfd_mips_elf_swap_abiflags_v0_in): Prototype.
(bfd_mips_elf_swap_abiflags_v0_out): Likewise.
(bfd_mips_isa_ext): Likewise.
bfd/
* elfxx-mips.c (ABI_O32_P, MIPS_ELF_ABIFLAGS_SECTION_NAME_P): New macro.
(mips_elf_obj_tdata): Add abiflags and abiflags_valid fields.
(bfd_mips_elf_swap_abiflags_v0_in): New function.
(bfd_mips_elf_swap_abiflags_v0_out): Likewise.
(_bfd_mips_elf_section_from_shdr): Handle SHT_MIPS_ABIFLAGS.
(_bfd_mips_elf_fake_sections): Likewise.
(_bfd_mips_elf_always_size_sections): Handle .MIPS.abiflags.
(_bfd_mips_elf_additional_program_headers): Account for new
PT_MIPS_ABIFLAGS program header.
(_bfd_mips_elf_modify_segment_map): Create PT_MIPS_ABIFLAGS segment and
associate with .MIPS.abiflags.
(_bfd_mips_elf_gc_mark_extra_sections): New function.
(bfd_mips_isa_ext, update_mips_abiflags_isa): New static function.
(infer_mips_abiflags): Likewise.
(_bfd_mips_elf_final_link): Handle .MIPS.abiflags.
(mips_32bit_flags_p): Moved higher.
(mips_elf_merge_obj_attributes, _bfd_mips_fp_abi_string): Error
checking for FP ABIs.
(_bfd_mips_elf_merge_private_bfd_data): Restructure and add abiflags
checks. Check EF_MIPS_FP64 flag consistency.
(print_mips_ases, print_mips_isa_ext): New static function.
(print_mips_fp_abi_value, get_mips_reg_size): Likewise.
(_bfd_mips_elf_print_private_bfd_data): Display abiflags data.
(_bfd_mips_post_process_headers): Set EI_ABIVERSION = 3 for
Val_GNU_MIPS_ABI_FP_64 or Val_GNU_MIPS_ABI_FP_64A.
* elfxx-mips.h (_bfd_mips_elf_gc_mark_extra_sections): New prototype.
* elf32-mips.c (elf_backend_gc_mark_extra_sections): Implement.
* elfn32-mips.c (elf_backend_gc_mark_extra_sections): Implement.
* elf64-mips.c (elf_backend_gc_mark_extra_sections): Implement.
binutils/
* readelf.c (get_mips_segment_type): Display name for PT_MIPS_ABIFLAGS.
(get_mips_section_type_name): Display name for SHT_MIPS_ABIFLAGS.
(display_mips_gnu_attribute): Abstracted fp abi printing to...
(print_mips_fp_abi_value): New static function. Handle new FP ABIs.
(print_mips_ases, print_mips_isa_ext): New static functions.
(get_mips_reg_size): Likewise.
(process_mips_specific): Display abiflags data.
elfcpp/
* elfcpp.h (PT_MIPS_ABIFLAGS): New program header type.
gas/
* config/tc-mips.c (mips_flags_frag): New static global.
(struct mips_set_options): Add oddspreg field.
(file_mips_opts, mips_opts): Initialize oddspreg.
(ISA_HAS_ODD_SINGLE_FPR): Add CPU argument and update for R5900 and
Loongson-3a.
(enum options, md_longopts, md_parse_option): Add -mfpxx, -modd-spreg
and -mno-odd-spreg options.
(md_begin): Create .MIPS.abiflags section.
(fpabi_incompatible_with, fpabi_requires): New static function.
(check_fpabi): Likewise.
(mips_check_options): Handle fp=xx and oddspreg restrictions.
(file_mips_check_options): Set oddspreg by default for fp=xx.
(mips_oddfpreg_ok): Re-write function.
(check_regno): Check odd numbered registers regardless of FPR size.
For fp != 32 use as_bad instead of as_warn.
(match_float_constant): Rewrite check regarding FP register width. Add
support for generating constants when MXHC1 is present. Handle fp=xx
to comply with the ABI.
(macro): Update M_LI_DD similarly to match_float_constant. Generate
MTHC1 when available. Check that correct code can be generated for
fp=xx and fp=64 ABIs.
(parse_code_option, s_mipsset): Add fp=xx, oddspreg and nooddspreg
options.
(mips_convert_ase_flags): New static function.
(mips_elf_final_processing): Use fpabi == Val_GNU_MIPS_ABI_FP_OLD_64
to determine when to add the EF_MIPS_FP64 flag. Populate the
.MIPS.abiflags section.
(md_mips_end): Update .gnu_attribute based on command line and .module
as applicable. Use check_fpabi to ensure .gnu.attribute and command
line/.module options are consistent.
* doc/as.texinfo: Add missing -mgp64/-mfp64 options and document new
-mfpxx, -modd-spreg and -mno-odd-spreg options.
* doc/c-mips.texi: Document -mfpxx, -modd-spreg, -mno-odd-spreg,
gnu_attribute values and FP ABIs.
ld/
* emulparams/elf32bmip.sh: Add .MIPS.abiflags.
* emulparams/elf32bmipn32-defs.sh: Likewise.
* emulparams/elf64bmip-defs.sh: Likewise.
opcodes/
* micromips-opc.c (COD, LCD) New macros.
(cfc1, ctc1): Remove FP_S attribute.
(dmfc1, mfc1, mfhc1): Add LCD attribute.
(dmtc1, mtc1, mthc1): Add COD attribute.
* mips-opc.c (cfc1, cftc1, ctc, cttc1): Remove FP_S attribute.
binutils/testsuite/
* binutils-all/readelf.s: Account for .MIPS.abiflags and
.gnu.attributes.
* binutils-all/readelf.ss-tmips: Likewise.
* binutils-all/strip-3.d: Likewise.
gas/testsuite/
* gas/mips/attr-gnu-4-0.d: New.
* gas/mips/attr-gnu-4-0.s: Likewise.
* gas/mips/attr-gnu-4-1-mfp32.l: Likewise.
* gas/mips/attr-gnu-4-1-mfp32.s: Likewise.
* gas/mips/attr-gnu-4-1-mfp64.l: Likewise.
* gas/mips/attr-gnu-4-1-mfp64.s: Likewise.
* gas/mips/attr-gnu-4-1-mfpxx.s: Likewise.
* gas/mips/attr-gnu-4-1-msingle-float.l: Likewise.
* gas/mips/attr-gnu-4-1-msingle-float.s: Likewise.
* gas/mips/attr-gnu-4-1-msoft-float.l: Likewise.
* gas/mips/attr-gnu-4-1-msoft-float.s: Likewise.
* gas/mips/attr-gnu-4-1.d: Likewise.
* gas/mips/attr-gnu-4-1.s: Likewise.
* gas/mips/attr-gnu-4-2-mdouble-float.l: Likewise.
* gas/mips/attr-gnu-4-2-mdouble-float.s: Likewise.
* gas/mips/attr-gnu-4-2-msoft-float.l: Likewise.
* gas/mips/attr-gnu-4-2-msoft-float.s: Likewise.
* gas/mips/attr-gnu-4-2.d: Likewise.
* gas/mips/attr-gnu-4-2.s: Likewise.
* gas/mips/attr-gnu-4-3-mhard-float.l: Likewise.
* gas/mips/attr-gnu-4-3-mhard-float.s: Likewise.
* gas/mips/attr-gnu-4-3.d: Likewise.
* gas/mips/attr-gnu-4-3.s: Likewise.
* gas/mips/attr-gnu-4-4.l: Likewise.
* gas/mips/attr-gnu-4-4.s: Likewise.
* gas/mips/attr-gnu-4-5-64.l: Likewise.
* gas/mips/attr-gnu-4-5-64.s: Likewise.
* gas/mips/attr-gnu-4-5.d: Likewise.
* gas/mips/attr-gnu-4-5.l: Likewise.
* gas/mips/attr-gnu-4-5.s: Likewise.
* gas/mips/attr-gnu-4-6-64.l: Likewise.
* gas/mips/attr-gnu-4-6-64.s: Likewise.
* gas/mips/attr-gnu-4-6.d: Likewise.
* gas/mips/attr-gnu-4-6.l: Likewise.
* gas/mips/attr-gnu-4-6.s: Likewise.
* gas/mips/attr-gnu-4-6-msingle-float.l: Likewise.
* gas/mips/attr-gnu-4-6-msingle-float.s: Likewise.
* gas/mips/attr-gnu-4-6-msoft-float.l: Likewise.
* gas/mips/attr-gnu-4-6-msoft-float.s: Likewise.
* gas/mips/attr-gnu-4-6-noodd.l: Likewise.
* gas/mips/attr-gnu-4-6-noodd.s: Likewise.
* gas/mips/attr-gnu-4-7-64.l: Likewise.
* gas/mips/attr-gnu-4-7-64.s: Likewise.
* gas/mips/attr-gnu-4-7-msingle-float.l: Likewise.
* gas/mips/attr-gnu-4-7-msingle-float.s: Likewise.
* gas/mips/attr-gnu-4-7-msoft-float.l: Likewise.
* gas/mips/attr-gnu-4-7-msoft-float.s: Likewise.
* gas/mips/attr-gnu-4-7-odd.l: Likewise.
* gas/mips/attr-gnu-4-7-odd.s: Likewise.
* gas/mips/attr-gnu-4-7.d: Likewise.
* gas/mips/attr-gnu-4-7.l: Likewise.
* gas/mips/attr-gnu-4-7.s: Likewise.
* gas/mips/attr-none-double.d: Likewise.
* gas/mips/attr-none-o32-fp64.d: Likewise.
* gas/mips/attr-none-o32-fp64-nooddspreg.d
* gas/mips/attr-none-o32-fpxx.d: Likewise.
* gas/mips/attr-none-single-float.d: Likewise.
* gas/mips/attr-none-soft-float.d: Likewise.
* gas/mips/elf_arch_mips32r3.d: Likewise.
* gas/mips/elf_arch_mips32r5.d: Likewise.
* gas/mips/elf_arch_mips64r3.d: Likewise.
* gas/mips/elf_arch_mips64r5.d: Likewise.
* gas/mips/li-d.d: Likewise.
* gas/mips/li-d.s: Likewise.
* gas/mips/module-check-warn.l: Likewise.
* gas/mips/module-check-warn.s: Likewise.
* gas/mips/module-check.d: Likewise.
* gas/mips/module-check.s: Likewise.
* gas/mips/module-mfp32.d: Likewise.
* gas/mips/module-mfp32.s: Likewise.
* gas/mips/module-mfp64.d: Likewise.
* gas/mips/module-mfp64.s: Likewise.
* gas/mips/module-mfp64-noodd.d: Likewise.
* gas/mips/module-mfp64-noodd.s: Likewise.
* gas/mips/module-mfpxx.d: Likewise.
* gas/mips/module-mfpxx.s: Likewise.
* gas/mips/module-msingle-float.d: Likewise.
* gas/mips/module-msingle-float.s: Likewise.
* gas/mips/module-msoft-float.d: Likewise.
* gas/mips/module-msoft-float.s: Likewise.
* gas/mips/module-set-mfpxx.d: Likewise.
* gas/mips/module-set-mfpxx.s: Likewise.
* gas/mips/fpxx-oddfpreg.d: Likewise.
* gas/mips/fpxx-oddfpreg.l: Likewise.
* gas/mips/fpxx-oddfpreg.s: Likewise.
* gas/mips/no-odd-spreg.d: Likewise.
* gas/mips/odd-spreg.d: Likewise.
* gas/elf/section2.e-mips: Adjust expected output.
* gas/mips/attr-gnu-abi-fp-1.d: Likewise.
* gas/mips/attr-gnu-abi-msa-1.d: Likewise.
* gas/mips/call-nonpic-1.d: Likewise.
* gas/mips/elf_arch_mips1.d: Likewise.
* gas/mips/elf_arch_mips2.d: Likewise.
* gas/mips/elf_arch_mips3.d: Likewise.
* gas/mips/elf_arch_mips32.d: Likewise.
* gas/mips/elf_arch_mips32r2.d: Likewise.
* gas/mips/elf_arch_mips4.d: Likewise.
* gas/mips/elf_arch_mips5.d: Likewise.
* gas/mips/elf_arch_mips64.d: Likewise.
* gas/mips/elf_arch_mips64r2.d: Likewise.
* gas/mips/elf_ase_micromips-2.d: Likewise.
* gas/mips/elf_ase_micromips.d: Likewise.
* gas/mips/elf_ase_mips16-2.d: Likewise.
* gas/mips/elf_ase_mips16.d: Likewise.
* gas/mips/module-defer-warn1.d: Likewise.
* gas/mips/module-override.d: Likewise.
* gas/mips/n32-consec.d: Likewise.
* gas/mips/nan-2008-1.d: Likewise.
* gas/mips/nan-2008-2.d: Likewise.
* gas/mips/nan-2008-3.d: Likewise.
* gas/mips/nan-2008-4.d: Likewise.
* gas/mips/nan-legacy-1.d: Likewise.
* gas/mips/nan-legacy-2.d: Likewise.
* gas/mips/nan-legacy-3.d: Likewise.
* gas/mips/nan-legacy-4.d: Likewise.
* gas/mips/nan-legacy-5.d: Likewise.
* gas/mips/tmips16-e.d: Likewise.
* gas/mips/tmips16-f.d: Likewise.
* gas/mips/tmipsel16-e.d: Likewise.
* gas/mips/tmipsel16-f.d: Likewise.
* gas/testsuite/gas/mips/mips.exp: Add new tests.
ld/testsuite/
* ld-mips-elf/abiflags-strip1-ph.d: New.
* ld-mips-elf/abiflags-strip2-ph.d: Likewise.
* ld-mips-elf/abiflags-strip3-ph.d: Likewise.
* ld-mips-elf/abiflags-strip4-ph.d: Likewise.
* ld-mips-elf/abiflags-strip5-ph.d: Likewise.
* ld-mips-elf/abiflags-strip6-ph.d: Likewise.
* ld-mips-elf/abiflags-strip7-ph.d: Likewise.
* ld-mips-elf/abiflags-strip8-ph.d: Likewise.
* ld-mips-elf/abiflags-strip9-ph.d: Likewise.
* ld-mips-elf/attr-gnu-4-0-n32-ph.d: Likewise.
* ld-mips-elf/attr-gnu-4-0-n64-ph.d: Likewise.
* ld-mips-elf/attr-gnu-4-0-ph.d: Likewise.
* ld-mips-elf/attr-gnu-4-06.d: Likewise.
* ld-mips-elf/attr-gnu-4-07.d: Likewise.
* ld-mips-elf/attr-gnu-4-08.d: Likewise.
* ld-mips-elf/attr-gnu-4-1-n32-ph.d: Likewise.
* ld-mips-elf/attr-gnu-4-1-n64-ph.d: Likewise.
* ld-mips-elf/attr-gnu-4-1-ph.d: Likewise.
* ld-mips-elf/attr-gnu-4-16.d: Likewise.
* ld-mips-elf/attr-gnu-4-17.d: Likewise.
* ld-mips-elf/attr-gnu-4-18.d: Likewise.
* ld-mips-elf/attr-gnu-4-2-n32-ph.d: Likewise.
* ld-mips-elf/attr-gnu-4-2-n64-ph.d: Likewise.
* ld-mips-elf/attr-gnu-4-2-ph.d: Likewise.
* ld-mips-elf/attr-gnu-4-26.d: Likewise.
* ld-mips-elf/attr-gnu-4-27.d: Likewise.
* ld-mips-elf/attr-gnu-4-28.d: Likewise.
* ld-mips-elf/attr-gnu-4-3-n32-ph.d: Likewise.
* ld-mips-elf/attr-gnu-4-3-n64-ph.d: Likewise.
* ld-mips-elf/attr-gnu-4-3-ph.d: Likewise.
* ld-mips-elf/attr-gnu-4-36.d: Likewise.
* ld-mips-elf/attr-gnu-4-37.d: Likewise.
* ld-mips-elf/attr-gnu-4-38.d: Likewise.
* ld-mips-elf/attr-gnu-4-4-ph.d: Likewise.
* ld-mips-elf/attr-gnu-4-46.d: Likewise.
* ld-mips-elf/attr-gnu-4-47.d: Likewise.
* ld-mips-elf/attr-gnu-4-48.d: Likewise.
* ld-mips-elf/attr-gnu-4-5-ph.d: Likewise.
* ld-mips-elf/attr-gnu-4-50.d: Likewise.
* ld-mips-elf/attr-gnu-4-52.d: Likewise.
* ld-mips-elf/attr-gnu-4-53.d: Likewise.
* ld-mips-elf/attr-gnu-4-54.d: Likewise.
* ld-mips-elf/attr-gnu-4-55.d: Likewise.
* ld-mips-elf/attr-gnu-4-56.d: Likewise.
* ld-mips-elf/attr-gnu-4-57.d: Likewise.
* ld-mips-elf/attr-gnu-4-58.d: Likewise.
* ld-mips-elf/attr-gnu-4-6-ph.d: Likewise.
* ld-mips-elf/attr-gnu-4-6.s: Likewise.
* ld-mips-elf/attr-gnu-4-60.d: Likewise.
* ld-mips-elf/attr-gnu-4-61.d: Likewise.
* ld-mips-elf/attr-gnu-4-62.d: Likewise.
* ld-mips-elf/attr-gnu-4-63.d: Likewise.
* ld-mips-elf/attr-gnu-4-64.d: Likewise.
* ld-mips-elf/attr-gnu-4-65.d: Likewise.
* ld-mips-elf/attr-gnu-4-66.d: Likewise.
* ld-mips-elf/attr-gnu-4-67.d: Likewise.
* ld-mips-elf/attr-gnu-4-68.d: Likewise.
* ld-mips-elf/attr-gnu-4-7-ph.d: Likewise.
* ld-mips-elf/attr-gnu-4-7.s: Likewise.
* ld-mips-elf/attr-gnu-4-70.d: Likewise.
* ld-mips-elf/attr-gnu-4-71.d: Likewise.
* ld-mips-elf/attr-gnu-4-72.d: Likewise.
* ld-mips-elf/attr-gnu-4-73.d: Likewise.
* ld-mips-elf/attr-gnu-4-74.d: Likewise.
* ld-mips-elf/attr-gnu-4-75.d: Likewise.
* ld-mips-elf/attr-gnu-4-76.d: Likewise.
* ld-mips-elf/attr-gnu-4-77.d: Likewise.
* ld-mips-elf/attr-gnu-4-78.d: Likewise.
* ld-mips-elf/attr-gnu-4-8.s: Likewise.
* ld-mips-elf/attr-gnu-4-81.d: Likewise.
* ld-mips-elf/empty.s: Likewise.
* ld-mips-elf/attr-gnu-4-00.d: Adjust expected output.
* ld-mips-elf/attr-gnu-4-01.d: Likewise.
* ld-mips-elf/attr-gnu-4-02.d: Likewise.
* ld-mips-elf/attr-gnu-4-03.d: Likewise.
* ld-mips-elf/attr-gnu-4-04.d: Likewise.
* ld-mips-elf/attr-gnu-4-05.d: Likewise.
* ld-mips-elf/attr-gnu-4-10.d: Likewise.
* ld-mips-elf/attr-gnu-4-11.d: Likewise.
* ld-mips-elf/attr-gnu-4-14.d: Likewise.
* ld-mips-elf/attr-gnu-4-15.d: Likewise.
* ld-mips-elf/attr-gnu-4-2.s: Likewise.
* ld-mips-elf/attr-gnu-4-20.d: Likewise.
* ld-mips-elf/attr-gnu-4-22.d: Likewise.
* ld-mips-elf/attr-gnu-4-24.d: Likewise.
* ld-mips-elf/attr-gnu-4-25.d: Likewise.
* ld-mips-elf/attr-gnu-4-3.s: Likewise.
* ld-mips-elf/attr-gnu-4-30.d: Likewise.
* ld-mips-elf/attr-gnu-4-33.d: Likewise.
* ld-mips-elf/attr-gnu-4-34.d: Likewise.
* ld-mips-elf/attr-gnu-4-35.d: Likewise.
* ld-mips-elf/attr-gnu-4-40.d: Likewise.
* ld-mips-elf/attr-gnu-4-41.d: Likewise.
* ld-mips-elf/attr-gnu-4-42.d: Likewise.
* ld-mips-elf/attr-gnu-4-43.d: Likewise.
* ld-mips-elf/attr-gnu-4-44.d: Likewise.
* ld-mips-elf/attr-gnu-4-45.d: Likewise.
* ld-mips-elf/attr-gnu-4-5.s: Likewise.
* ld-mips-elf/attr-gnu-4-51.d: Likewise.
* ld-mips-elf/attr-gnu-8-00.d: Likewise.
* ld-mips-elf/attr-gnu-8-01.d: Likewise.
* ld-mips-elf/attr-gnu-8-02.d: Likewise.
* ld-mips-elf/attr-gnu-8-10.d: Likewise.
* ld-mips-elf/attr-gnu-8-11.d: Likewise.
* ld-mips-elf/attr-gnu-8-20.d: Likewise.
* ld-mips-elf/attr-gnu-8-22.d: Likewise.
* ld-mips-elf/jalx-2.dd: Likewise.
* ld-mips-elf/mips16-pic-1.gd: Likewise.
* ld-mips-elf/mips16-pic-2.gd: Likewise.
* ld-mips-elf/mips16-pic-3.gd: Likewise.
* ld-mips-elf/mips16-pic-4a.gd: Likewise.
* ld-mips-elf/multi-got-no-shared.d: Likewise.
* ld-mips-elf/nan-2008.d: Likewise.
* ld-mips-elf/nan-legacy.d: Rework test.
* ld-mips-elf/pic-and-nonpic-3a.gd: Likewise.
* ld-mips-elf/pic-and-nonpic-3b.gd: Likewise.
* ld-mips-elf/pic-and-nonpic-5b.gd: Likewise.
* ld-mips-elf/pic-and-nonpic-6.ld: Likewise.
* ld-mips-elf/rel32-n32.d: Likewise.
* ld-mips-elf/rel32-o32.d: Likewise.
* ld-mips-elf/rel64.d: Likewise.
* ld-mips-elf/tls-multi-got-1.r: Likewise.
* ld-elf/group.ld: Discard .MIPS.abiflags and .gnu.attributes.
* ld-elf/orphan-region.ld: Likewise.
* ld-elf/orphan.ld: Likewise.
* ld-mips-elf/compressed-plt-1.ld: Likewise.
* ld-mips-elf/dyn-sec64.ld: Likewise.
* ld-mips-elf/got-dump-1.ld: Likewise.
* ld-mips-elf/got-dump-2.ld: Likewise.
* ld-mips-elf/got-page-1.ld: Likewise.
* ld-mips-elf/mips-dyn.ld: Likewise.
* ld-mips-elf/mips-lib.ld: Likewise.
* ld-mips-elf/pic-and-nonpic-3a.ld: Likewise.
* ld-mips-elf/pic-and-nonpic-3b.ld: Likewise.
* ld-mips-elf/pic-and-nonpic-4b.ld: Likewise.
* ld-mips-elf/pic-and-nonpic-5b.ld: Likewise.
* ld-mips-elf/region1.t: Likewise.
* ld-mips-elf/stub-dynsym-1.ld: Likewise.
* ld-mips-elf/tls-hidden3.ld: Likewise.
* ld-mips-elf/vxworks1.ld: Likewise.
* ld-scripts/overlay-size.t: Likewise.
* ld-mips-elf/elf-rel-got-n32-embed.d: Remove .MIPS.abiflags from
objects.
* ld-mips-elf/elf-rel-got-n32.d: Likewise.
* ld-mips-elf/elf-rel-got-n64-embed.d: Likewise.
* ld-mips-elf/elf-rel-got-n64-linux.d: Likewise.
* ld-mips-elf/elf-rel-got-n64.d: Likewise.
* ld-mips-elf/elf-rel-xgot-n32.d: Likewise.
* ld-mips-elf/elf-rel-xgot-n32-embed.d: Likewise.
* ld-mips-elf/elf-rel-xgot-n64.d: Likewise.
* ld-mips-elf/elf-rel-xgot-n64-linux.d: Likewise.
* ld-mips-elf/elf-rel-xgot-n64-embed.d: Likewise.
* ld-mips-elf/mips-elf.exp: Add new tests.
|
|
|
|
The element index range for the following MIPS MSA instructions: sldi, splati,
copy_s, copy_u, insert and insve is 1 bit too large. This patch fixes this issue.
ChangeLog:
gas/testsuite/gas/mips/
* msa.s: Reduced maximum element index range for sldi, splati,
copy_s, copy_u, insert and insve instructions.
* msa64.s: Likewise.
* micromips@msa.d: Likewise.
* micromips@msa64.d: Likewise.
* msa.d: Likewise.
* msa64.d: Likewise.
include/opcode/
* mips.h: Updated description of +o, +u, +v and +w for MIPS and
microMIPS.
opcodes/
* micromips-opc.c (decode_micromips_operand): Reduced range of +o, +u,
+v and +w.
(micromips_opcodes): Reduced element index range for sldi, splati,
copy_s, copy_u, insert and insve instructions.
* opcodes/mips-opc.c (decode_mips_operand): Reduced range of +o, +u,
+v and +w.
(mips_builtin_opcodes): Reduced element index range for sldi, splati,
copy_s, copy_u, insert and insve instructions.
|
|
* micromips-opc.c (LM): Define.
(micromips_opcodes): Add LM to load instructions.
* mips-opc.c (prefe): Add LM attribute.
|
|
* micromips-opc.c (decode_micromips_operand): Add +T, +U, +V, +W,
+d, +e, +h, +k, +l, +n, +o, +u, +v, +w, +x,
+~, +!, +@, +#, +$, +%, +^, +&, +*, +|.
(MSA): New define.
(MSA64): New define.
(micromips_opcodes): Add MSA instructions.
* mips-dis.c (msa_control_names): New array.
(mips_abi_choice): Add ASE_MSA to mips32r2.
Remove ASE_MDMX from mips64r2.
Add ASE_MSA and ASE_MSA64 to mips64r2.
(parse_mips_dis_option): Handle -Mmsa.
(print_reg): Handle cases for OP_REG_MSA and OP_REG_MSA_CTRL.
(print_insn_arg): Handle cases for OP_IMM_INDEX and OP_REG_INDEX.
(print_mips_disassembler_options): Print -Mmsa.
* mips-opc.c (decode_mips_operand): Add +T, +U, +V, +W, +d, +e, +h, +k,
+l, +n, +o, +u, +v, +w, +~, +!, +@, +#, +$, +%, +^, +&, +*, +|.
(MSA): New define.
(MSA64): New define.
(mips_builtin_op): Add MSA instructions.
|
|
* micromips-opc.c (micromips_opcodes): Fix dmfgc0 and dmtgc0.
|
|
* micromips-opc.c (micromips_opcodes): Use RD_4 for "alnv.ps",
replacing NODS.
gas/testsuite/
* gas/testsuite/gas/mips/micromips-insn32.d: Adjust for delay
slot scheduling of ALNV.PS.
* gas/testsuite/gas/mips/micromips-noinsn32.d: Likewise.
* gas/testsuite/gas/mips/micromips-trap.d: Likewise.
* gas/testsuite/gas/mips/micromips.d: Likewise.
* gas/testsuite/gas/mips/micromips@alnv_ps-swap.d: Likewise.
|
|
* mips.h (M_DEXT, M_DINS): Delete.
opcodes/
* micromips-opc.c (micromips_opcodes): Replace "dext" and "dins"
macro entries with "dextm", "dextu", "dinsm" and "dinsu" aliases.
Use +H rather than +C for the real "dext".
* mips-opc.c (mips_builtin_opcodes): Likewise.
gas/
* config/tc-mips.c (report_bad_range, report_bad_field): Delete.
(macro): Remove M_DEXT and M_DINS handling.
gas/testsuite/
* gas/mips/ext-ill.l, gas/mips/mips64r2-ill.l: Expect DEXT and DINS
error messages to have the same form as the EXT and INS ones.
* gas/mips/micromips-insn32.d, gas/mips/micromips-noinsn32.d,
gas/mips/micromips-trap.d, gas/mips/micromips.d,
gas/mips/micromips@mips64r2.d, gas/mips/mips64r2.d: Expect
"dext" and "dins" instead of "dextm", "dextu", "dinsm" and "dinsu".
|
|
* mips.h (OP_OPTIONAL_REG): New mips_operand_type.
(mips_optional_operand_p): New function.
opcodes/
* mips-formats.h (OPTIONAL_REG, OPTIONAL_MAPPED_REG): New macros.
* micromips-opc.c (decode_micromips_operand): Use OPTIONAL_REG
and OPTIONAL_MAPPED_REG.
* mips-opc.c (decode_mips_operand): Likewise.
* mips16-opc.c (decode_mips16_operand): Likewise.
* mips-dis.c (print_insn_arg): Handle OP_OPTIONAL_REG.
gas/
* config/tc-mips.c (operand_reg_mask, match_operand): Handle
OP_OPTIONAL_REG.
(mips_ip, mips16_ip): Use mips_optional_operand_p to check
for optional operands.
|
|
* micromips-opc.c (WR_s): Delete.
|
|
* mips.h (mips_decode_reg_operand): New function.
(INSN_WRITE_SHIFT, INSN_WRITE_1, INSN_WRITE_2, INSN_WRITE_ALL)
(INSN_READ_SHIFT, INSN_READ_1, INSN_READ_2, INSN_READ_3, INSN_READ_4)
(INSN_READ_ALL, INSN_READ_GPR_24, INSN_WRITE_GPR_24, INSN_UDI):
New macros.
(INSN_WRITE_GPR_D, INSN_WRITE_GPR_T, INSN_WRITE_FPR_D)
(INSN_WRITE_FPR_S, INSN_WRITE_FPR_T, INSN_READ_GPR_S, INSN_READ_GPR_T)
(INSN_READ_FPR_S, INSN_READ_FPR_T, INSN_READ_FPR_R, INSN_WRITE_GPR_S)
(INSN2_WRITE_GPR_Z, INSN2_WRITE_FPR_Z, INSN2_READ_GPR_Z)
(INSN2_READ_FPR_Z, INSN2_READ_GPR_D, INSN2_READ_FPR_D)
(INSN2_WRITE_GPR_MB, INSN2_READ_GPR_MC, INSN2_MOD_GPR_MD)
(INSN2_READ_GPR_ME, INSN2_MOD_GPR_MF, INSN2_READ_GPR_MG)
(INSN2_READ_GPR_MJ, INSN2_WRITE_GPR_MJ, INSN2_READ_GPR_MP)
(INSN2_WRITE_GPR_MP, INSN2_READ_GPR_MQ, INSN2_READ_GP)
(INSN2_WRITE_GPR_MH, INSN2_READ_GPR_MMN): Delete. Renumber other
macros to cover the gaps.
(INSN2_MOD_SP): Replace with...
(INSN2_WRITE_SP, INSN2_READ_SP): ...these new macros.
(MIPS16_INSN_WRITE_X, MIPS16_INSN_WRITE_Y, MIPS16_INSN_WRITE_Z)
(MIPS16_INSN_WRITE_T, MIPS16_INSN_WRITE_31, MIPS16_INSN_WRITE_GPR_Y)
(MIPS16_INSN_READ_X, MIPS16_INSN_READ_Y, MIPS16_INSN_READ_Z)
(MIPS16_INSN_READ_T, MIPS16_INSN_READ_SP, MIPS16_INSN_READ_GPR_X):
Delete.
opcodes/
* mips-opc.c (WR_1, WR_2, RD_1, RD_2, RD_3, RD_4, MOD_1, MOD_2, UDI):
New macros.
(WR_d, WR_t, WR_D, WR_T, WR_S, RD_s, RD_b, RD_t, RD_S, RD_T, RD_R)
(WR_z, WR_Z, RD_z, RD_Z, RD_d): Delete.
(mips_builtin_opcodes): Use the new position-based read-write flags
instead of field-based ones. Use UDI for "udi..." instructions.
* mips16-opc.c (WR_1, WR_2, RD_1, RD_2, RD_3, RD_4, MOD_1, MOD_2):
New macros.
(WR_x, WR_y, WR_z, WR_Y, RD_x, RD_y, RD_Z, RD_X): Delete.
(RD_T, WR_T, WR_31): Redefine using generic INSN_* flags.
(WR_SP, RD_16): New macros.
(RD_SP): Redefine as an INSN2_* flag.
(MOD_SP): Redefine in terms of RD_SP and WR_SP.
(mips16_opcodes): Use the new position-based read-write flags
instead of field-based ones. Use RD_16 for "nop". Move RD_SP to
pinfo2 field.
* micromips-opc.c (WR_1, WR_2, RD_1, RD_2, RD_3, RD_4, MOD_1, MOD_2):
New macros.
(WR_mb, RD_mc, RD_md, WR_md, RD_me, RD_mf, WR_mf, RD_mg, WR_mh, RD_mj)
(WR_mj, RD_ml, RD_mmn, RD_mp, WR_mp, RD_mq, RD_gp, WR_d, WR_t, WR_D)
(WR_T, WR_S, RD_s, RD_b, RD_t, RD_T, RD_S, RD_R, RD_D): Delete.
(RD_sp, WR_sp): Redefine to INSN2_READ_SP and INSN2_WRITE_SP.
(micromips_opcodes): Use the new position-based read-write flags
instead of field-based ones.
* mips-dis.c (print_insn_arg): Use mips_decode_reg_operand.
(print_insn_mips, print_insn_micromips): Use INSN_WRITE_1 instead
of field-based flags.
gas/
* config/tc-mips.c (MAX_OPERANDS): New macro.
(mips_operand_array): New structure.
(mips_operands, mips16_operands, micromips_operands): New arrays.
(micromips_to_32_reg_b_map, micromips_to_32_reg_c_map)
(micromips_to_32_reg_e_map, micromips_to_32_reg_f_map)
(micromips_to_32_reg_g_map, micromips_to_32_reg_l_map)
(micromips_to_32_reg_q_map): Delete.
(insn_operands, insn_opno, insn_extract_operand): New functions.
(validate_mips_insn): Take a mips_operand_array as argument and
use it to build up a list of operands. Extend to handle INSN_MACRO
and MIPS16.
(validate_mips16_insn): New function.
(validate_micromips_insn): Take a mips_operand_array as argument.
Handle INSN_MACRO.
(md_begin): Initialize mips_operands, mips16_operands and
micromips_operands. Call validate_mips_insn and
validate_micromips_insn for macro instructions too.
Call validate_mips16_insn for MIPS16 instructions.
(insn_read_mask, insn_write_mask, operand_reg_mask, insn_reg_mask):
New functions.
(gpr_read_mask, gpr_write_mask, fpr_read_mask, fpr_write_mask): Use
them. Handle INSN_UDI.
(get_append_method): Use gpr_read_mask.
|
|
* mips-opc.c (mips_builtin_opcodes): Remove WR_* and RD_* flags
for operands that are hard-coded to $0.
* micromips-opc.c (micromips_opcodes): Likewise.
|
|
* mips-opc.c (mips_builtin_opcodes): Use WR_31 rather than WR_d
for the single-operand forms of JALR and JALR.HB.
* micromips-opc.c (micromips_opcodes): Likewise JALR, JALRS, JALR.HB
and JALRS.HB.
|
|
* Makefile.am (mips-opc.lo, micromips-opc.lo, mips16-opc.lo): Remove
special rules.
* Makefile.in: Regenerate.
* mips-opc.c, micromips-opc.c, mips16-opc.c: Explicitly initialize
all fields. Reformat.
|
|
* mips.h (mips_operand_type, mips_reg_operand_type): New enums.
(mips_operand, mips_int_operand, mips_mapped_int_operand)
(mips_msb_operand, mips_reg_operand, mips_reg_pair_operand)
(mips_pcrel_operand): New structures.
(mips_insert_operand, mips_extract_operand, mips_signed_operand)
(mips_decode_int_operand, mips_decode_pcrel_operand): New functions.
(decode_mips_operand, decode_micromips_operand): Declare.
opcodes/
* mips-formats.h: New file.
* mips-opc.c: Include mips-formats.h.
(reg_0_map): New static array.
(decode_mips_operand): New function.
* micromips-opc.c: Remove <stdio.h> include. Include mips-formats.h.
(reg_0_map, reg_28_map, reg_29_map, reg_31_map, reg_m16_map)
(reg_mn_map, reg_q_map, reg_h_map1, reg_h_map2, int_b_map)
(int_c_map): New static arrays.
(decode_micromips_operand): New function.
* mips-dis.c (micromips_to_32_reg_b_map, micromips_to_32_reg_c_map)
(micromips_to_32_reg_d_map, micromips_to_32_reg_e_map)
(micromips_to_32_reg_f_map, micromips_to_32_reg_g_map)
(micromips_to_32_reg_h_map1, micromips_to_32_reg_h_map2)
(micromips_to_32_reg_l_map, micromips_to_32_reg_m_map)
(micromips_to_32_reg_n_map, micromips_to_32_reg_q_map)
(micromips_imm_b_map, micromips_imm_c_map): Delete.
(print_reg): New function.
(mips_print_arg_state): New structure.
(init_print_arg_state, print_insn_arg): New functions.
(print_insn_args): Change interface and use mips_operand structures.
Delete GET_OP_S. Move GET_OP definition to...
(print_insn_mips): ...here. Update the call to print_insn_args.
(print_insn_micromips): Use print_insn_args.
gas/
* config/tc-mips.c (validate_mips_insn): Move further up file.
Add insn_bits and decode_operand arguments. Use the mips_operand
fields to work out which bits an operand occupies. Detect double
definitions.
(validate_micromips_insn): Move further up file. Call into
validate_mips_insn.
|
|
* mips.h (M_ACLR_OB, M_ASET_OB, M_CACHE_OB, M_CACHEE_OB, M_L_DOB)
(M_LB_A, M_LBE_OB, M_LBU_A, M_LBUE_OB, M_LD_A, M_LD_OB, M_LDC2_OB)
(M_LDL_OB, M_LDM_OB, M_LDP_OB, M_LDR_OB, M_LH_A, M_LHE_OB, M_LHU_A)
(M_LHUE_OB, M_LL_OB, M_LLD_OB, M_LLE_OB, M_LS_A, M_LW_A, M_LWE_OB)
(M_LWC0_A, M_LWC1_A, M_LWC2_A, M_LWC2_OB, M_LWC3_A, M_LWL_A, M_LWL_OB)
(M_LWLE_OB, M_LWM_OB, M_LWP_OB, M_LWR_A, M_LWR_OB, M_LWRE_OB, M_LWU_OB)
(M_PREF_OB, M_PREFE_OB, M_S_DOB, M_SAA_OB, M_SAAD_OB, M_SC_OB)
(M_SCD_OB, M_SCE_OB, M_SD_A, M_SD_OB, M_SDC2_OB, M_SDL_OB, M_SDM_OB)
(M_SDP_OB, M_SDR_OB, M_SB_A, M_SBE_OB, M_SH_A, M_SHE_OB, M_SW_A)
(M_SWE_OB, M_SWC0_A, M_SWC1_A, M_SWC2_A, M_SWC2_OB, M_SWC3_A, M_SWL_A)
(M_SWL_OB, M_SWLE_OB, M_SWM_OB, M_SWP_OB, M_SWR_A, M_SWR_OB, M_SWRE_OB)
(M_ULD, M_ULH, M_ULHU, M_ULW, M_USH, M_USW, M_USD): Delete.
(M_ULD_A, M_ULH_A, M_ULHU_A, M_ULW_A, M_USH_A, M_USW_A, M_USD_A):
Rename to...
(M_ULD_AB, M_ULH_AB, M_ULHU_AB, M_ULW_AB, M_USH_AB, M_USW_AB)
(M_USD_AB): ...these.
opcodes/
* mips-opc.c (mips_builtin_opcodes): Remove o(b) macros. Move LD
and SD A(B) macros up.
* micromips-opc.c (micromips_opcodes): Likewise.
gas/
* config/tc-mips.c (gprel16_reloc_p): New function.
(macro_read_relocs): Assume BFD_RELOC_LO16 if all relocs are
BFD_RELOC_UNUSED.
(offset_high_part, small_offset_p): New functions.
(nacro): Use them. Remove *_OB and *_DOB cases. For single-
register load and store macros, handle the 16-bit offset case first.
If a 16-bit offset is not suitable for the instruction we're
generating, load it into the temporary register using
ADDRESS_ADDI_INSN. Make the M_LI_DD code fall through into the
M_L_DAB code once the address has been constructed. For double load
and store macros, again handle the 16-bit offset case first.
If the second register cannot be accessed from the same high
part as the first, load it into AT using ADDRESS_ADDI_INSN.
Fix the handling of LD in cases where the first register is the
same as the base. Also handle the case where the offset is
not 16 bits and the second register cannot be accessed from the
same high part as the first. For unaligned loads and stores,
fuse the offbits == 12 and old "ab" handling. Apply this handling
whenever the second offset needs a different high part from the first.
Construct the offset using ADDRESS_ADDI_INSN where possible,
for offbits == 16 as well as offbits == 12. Use offset_reloc
when constructing the individual loads and stores.
(mips_ip): Set up imm_expr, imm2_expr, offset_expr, imm_reloc
and offset_reloc before matching against a particular opcode.
Handle elided 'A' constants. Allow 'A' constants to use
relocation operators.
gas/testsuite/
* gas/mips/ldstla-32.d: Avoid "lui at,0x0" sequences for
truncated constants.
* gas/mips/ldstla-32-shared.d: Likewise.
* gas/mips/mcu.d: Use ADDIU in preference to LI+ADDU when adding
16-bit constants to the base.
* gas/mips/micromips@mcu.d: Likewise.
* gas/mips/micromips@cache.d: Likewise.
* gas/mips/micromips@pref.d: Likewise.
* gas/mips/micromips.d, gas/mips/micromips-insn32.d,
gas/mips/micromips-noinsn32.d, gas/mips/micromips-trap.d: Likewise.
Allow the full 16-bit offset range to be used for SB, LB and LBU in
USH and ULH sequences. Fix the expected output for LD and SD when
the two LW and SW offsets need different high parts.
* gas/mips/eva.s: Test PREFE with relocation operators.
* gas/mips/eva.d: Use ADDIU in preference to LI+ADDU for 16-bit
constants. Update after eva.s change.
* gas/mips/micromips@eva.d: Likewise.
* gas/mips/ld-reloc.s, gas/mips/ld-reloc.d, gas/mips/l_d-reloc.s,
gas/mips/l_d-reloc.d, gas/mips/ulw-reloc.s, gas/mips/ulw-reloc.d,
gas/mips/micromips@ulw-reloc.d, gas/mips/ulh-reloc.s,
gas/mips/ulh-reloc.d: New tests.
* gas/mips/mips.exp: Run them.
|
|
* mips.h: Document "+i".
opcodes/
* mips-opc.c (mips_builtin_opcodes): Use "+i" rather than "a" for
"jalx".
* mips16-opc.c (mips16_opcodes): Likewise.
* micromips-opc.c (micromips_opcodes): Likewise.
* mips-dis.c (print_insn_args, print_mips16_insn_arg)
(print_insn_mips16): Handle "+i".
(print_insn_micromips): Likewise. Conditionally preserve the
ISA bit for "a" but not for "+i".
gas/
* config/tc-mips.c (validate_mips_insn, validate_micromips_insn):
(mips_ip, mips16_ip): Handle "+i".
|
|
* mips.h: Remove "mi" documentation. Update "mh" documentation.
(OP_MASK_MI, OP_SH_MI, MICROMIPSOP_MASK_MI, MICROMIPSOP_MASK_MI):
Delete.
(INSN2_WRITE_GPR_MHI): Rename to...
(INSN2_WRITE_GPR_MH): ...this.
opcodes/
* micromips-opc.c (WR_mhi): Rename to..
(WR_mh): ...this.
(micromips_opcodes): Update "movep" entry accordingly. Replace
"mh,mi" with "mh".
* mips-dis.c (micromips_to_32_reg_h_map): Rename to...
(micromips_to_32_reg_h_map1): ...this.
(micromips_to_32_reg_i_map): Rename to...
(micromips_to_32_reg_h_map2): ...this.
(print_micromips_insn): Remove "mi" case. Print both registers
in the pair for "mh".
gas/
* config/tc-mips.c (mips32_to_micromips_reg_h_map): Delete.
(micromips_to_32_reg_h_map): Rename to...
(micromips_to_32_reg_h_map1): ...this.
(micromips_to_32_reg_i_map): Rename to...
(micromips_to_32_reg_h_map2): ...this.
(mips_lookup_reg_pair): New function.
(gpr_write_mask, macro): Adjust after above renaming.
(validate_micromips_insn): Remove "mi" handling.
(mips_ip): Likewise. Parse both registers in a pair for "mh".
|
|
* mips.h: Remove documentation of "+D" and "+T".
opcodes/
* mips-opc.c (mips_builtin_opcodes): Remove "+D" and "+T" entries.
* micromips-opc.c (micromips_opcodes): Likewise.
* mips-dis.c (print_insn_args, print_insn_micromips): Remove "+D"
and "+T" handling. Check for a "0" suffix when deciding whether to
use coprocessor 0 names. In that case, also check for ",H" selectors.
gas/
* config/tc-mips.c (validate_mips_insn, validate_micromips_insn)
(mips_ip): Remove "+D" and "+T" handling.
gas/testsuite/
* gas/mips/lb.d, gas/mips/sb.d: Use coprocessor register names
for LWC0 and SWC0.
|
|
* elfxx-mips.h (_bfd_mips_elf_insn32): New prototype.
* elfxx-mips.c (mips_elf_link_hash_table): Add insn32 member.
(STUB_MOVE32_MICROMIPS, STUB_JALR32_MICROMIPS): New macros.
(MICROMIPS_INSN32_FUNCTION_STUB_NORMAL_SIZE): Likewise.
(MICROMIPS_INSN32_FUNCTION_STUB_BIG_SIZE): Likewise.
(micromips_insn32_o32_exec_plt0_entry): New variable.
(micromips_insn32_o32_exec_plt_entry): Likewise.
(_bfd_mips_elf_adjust_dynamic_symbol): Handle insn32 mode.
(mips_elf_estimate_stub_size): Likewise.
(_bfd_mips_elf_size_dynamic_sections): Likewise.
(_bfd_mips_elf_finish_dynamic_symbol): Likewise.
(mips_finish_exec_plt): Likewise.
(_bfd_mips_elf_relax_section): Likewise.
(_bfd_mips_elf_insn32): New function.
(_bfd_mips_elf_get_synthetic_symtab): Handle insn32 PLT.
gas/
* config/tc-mips.c (mips_set_options): Add insn32 member.
(mips_opts): Initialize it.
(NOP_INSN, NOP_INSN_SIZE): Handle insn32 mode.
(options): Add OPTION_INSN32 and OPTION_NO_INSN32 enum values.
(md_longopts): Add "minsn32" and "mno-insn32" options.
(is_size_valid): Handle insn32 mode.
(md_assemble): Pass instruction string down to macro.
(brk_fmt): Add second dimension and insn32 mode initializers.
(mfhl_fmt): Likewise.
(BRK_FMT, MFHL_FMT): Handle insn32 mode.
(macro_build) <'c'>: Handle microMIPS 32-bit BREAK encoding.
(macro_build_jalr, move_register): Handle insn32 mode.
(macro_build_branch_rs): Likewise.
(macro): Handle insn32 mode.
<M_JRADDIUSP>, <M_JRC>, <M_MOVEP>: New cases.
(mips_ip): Handle insn32 mode.
(md_parse_option): Handle OPTION_INSN32 and OPTION_NO_INSN32.
(s_mipsset): Handle "insn32" and "noinsn32" pseudo-ops.
(mips_handle_align): Handle insn32 mode.
(md_show_usage): Add -minsn32 and -mno-insn32.
* doc/as.texinfo (Target MIPS options): Add -minsn32 and
-mno-insn32 options.
(-minsn32, -mno-insn32): New options.
* doc/c-mips.texi (MIPS Opts): Add -minsn32 and -mno-insn32
options.
(MIPS assembly options): New node. Document .set insn32 and
.set noinsn32.
(MIPS-Dependent): List the new node.
gas/testsuite/
* gas/mips/micromips-insn32.d: New test.
* gas/mips/micromips-noinsn32.d: Likewise.
* gas/mips/micromips.l: Rename to...
* gas/mips/micromips-warn.l: ... this.
* gas/mips/micromips.d: Update accordingly.
* gas/mips/micromips-trap.d: Likewise.
* gas/mips/micromips.l: New list test.
* gas/mips/micromips.s: Add conditionals.
* gas/mips/mips.exp: Run the new tests.
include/opcode/
* mips.h: Add M_JRADDIUSP, M_JRC and M_MOVEP anonymous enum
values.
ld/
* emultempl/mipself.em (insn32): New variable.
(mips_create_output_section_statements): Handle insn32 mode.
(PARSE_AND_LIST_PROLOGUE): New macro.
(PARSE_AND_LIST_LONGOPTS): Likewise.
(PARSE_AND_LIST_OPTIONS): Likewise.
* gen-doc.texi: Set MIPS.
* ld.texinfo: Likewise.
(Options specific to MIPS targets): New section.
(ld and MIPS family): New node.
(Top, Machine Dependent): List the new node.
opcodes/
* micromips-opc.c (micromips_opcodes): Add "jraddiusp", "jrc"
and "movep" macros.
|
|
Maciej W. Rozycki <macro@codesourcery.com>
Chao-Ying Fu <fu@mips.com>
gas/testsuite/
* gas/mips/mips.exp: Run new tests.
* gas/mips/eva.d: New.
* gas/mips/eva.s: New.
* gas/mips/micromips@eva.d: New.
gas/
* config/tc-mips.c (mips_set_options): Add ase_eva.
(mips_set_options mips_opts): Add ase_eva.
(file_ase_eva): Declare.
(ISA_SUPPORTS_EVA_ASE): Define.
(IS_SEXT_9BIT_NUM): Define.
(MIPS_CPU_ASE_EVA): Define.
(is_opcode_valid): Add support for ase_eva.
(macro_build): Likewise.
(macro): Likewise.
(validate_mips_insn): Likewise.
(validate_micromips_insn): Likewise.
(mips_ip): Likewise.
(options): Add OPTION_EVA and OPTION_NO_EVA.
(md_longopts): Add -meva and -mno-eva.
(md_parse_option): Process new options.
(mips_after_parse_args): Check for valid EVA combinations.
(s_mipsset): Likewise.
include/
* opcode/mips.h (OP_SH_EVAOFFSET): Define.
(OP_MASK_EVAOFFSET): Define.
(INSN_ASE_MASK): Delete.
(ASE_EVA): Define.
(M_CACHEE_AB, M_CACHEE_OB): New.
(M_LBE_OB, M_LBE_AB): New.
(M_LBUE_OB, M_LBUE_AB): New.
(M_LHE_OB, M_LHE_AB): New.
(M_LHUE_OB, M_LHUE_AB): New.
(M_LLE_AB, M_LLE_OB): New.
(M_LWE_OB, M_LWE_AB): New.
(M_LWLE_AB, M_LWLE_OB): New.
(M_LWRE_AB, M_LWRE_OB): New.
(M_PREFE_AB, M_PREFE_OB): New.
(M_SCE_AB, M_SCE_OB): New.
(M_SBE_OB, M_SBE_AB): New.
(M_SHE_OB, M_SHE_AB): New.
(M_SWE_OB, M_SWE_AB): New.
(M_SWLE_AB, M_SWLE_OB): New.
(M_SWRE_AB, M_SWRE_OB): New.
(MICROMIPSOP_SH_EVAOFFSET): Define.
(MICROMIPSOP_MASK_EVAOFFSET): Define.
opcodes/
* micromips-opc.c (EVA): Define.
(TLBINV): Define.
(micromips_opcodes): Add EVA opcodes.
* mips-dis.c (mips_arch_choices): Update for ASE_EVA.
(print_insn_args): Handle EVA offsets.
(print_insn_micromips): Likewise.
* mips-opc.c (EVA): Define.
(TLBINV): Define.
(mips_builtin_opcodes): Add EVA opcodes.
|
|
* micromips-opc.c (IVIRT): New define.
(IVIRT64): New define.
(micromips_opcodes): Add dmfgc0, dmtgc0, hypcall, mfgc0, mtgc0,
tlbginv, tlbginvf, tlbgp, tlbgr, tlbgwi, tlbgwr VIRT instructions.
* mips-dis.c (print_insn_micromips): Handle mfgc0, mtgc0, dmfgc0,
dmtgc0 to print cp0 names.
|
|
2013-06-08 Catherine Moore <clm@codesourcery.com>
* config/tc-mips.c (is_opcode_valid): Build ASE mask.
(is_opcode_valid_16): Pass ase value to opcode_is_member.
(append_insn): Change INSN_xxxx to ASE_xxxx.
include/
2013-06-08 Catherine Moore <clm@codesourcery.com>
* opcode/mips.h (mips_opcode): Add ase field.
(INSN_ASE_MASK): Delete.
(INSN_DSP): Rename to ASE_DSP. Provide new value.
(INSN_DSPR2): Rename to ASE_DSPR2. Provide new value.
(INSN_MCU): Rename to ASE_MCU. Provide new value.
(INSN_MDMX): Rename to ASE_MDMX. Provide new value.
(INSN_MIPS3d): Rename to ASE_MIPS3D. Provide new value.
(INSN_MT): Rename to ASE_MT. Provide new value.
(INSN_SMARTMIPS): Rename to ASE_SMARTMIPS. Provide new value.
(INSN_VIRT): Rename to ASE_VIRT. Provide new value.
(INSN_VIRT64): Rename to ASE_VIRT64. Provide new value.
(opcode_is_member): Add ase argument. Check ase.
opcodes/
2013-06-08 Catherine Moore <clm@codesourcery.com>
Richard Sandiford <rdsandiford@googlemail.com>
* micromips-opc.c (D32, D33, MC): Update definitions.
(micromips_opcodes): Initialize ase field.
* mips-dis.c (mips_arch_choice): Add ase field.
(mips_arch_choices): Initialize ase field.
(set_default_mips_dis_options): Declare and setup mips_ase.
* mips-opc.c (M3D, SMT, MX, IVIRT, IVIRT64, D32, D33, D64,
MT32, MC): Update definitions.
(mips_builtin_opcodes): Initialize ase field.
|
|
* micromips-opc.c (micromips_opcodes): Correct the encoding of
the "swxc1" instruction.
gas/testsuite/
* gas/mips/micromips.d: Correct the disassembly of SWXC1.
* gas/mips/micromips-trap.d: Likewise.
* gas/mips/micromips@24k-triple-stores-1.d: Likewise.
* gas/mips/micromips@mips4-fp.d: Likewise.
|
|
* mips.h (mips_opcode): Add the exclusions field.
(OPCODE_IS_MEMBER): Remove macro.
(cpu_is_member): New inline function.
(opcode_is_member): Likewise.
opcodes/
* micromips-opc.c (micromips_opcodes): Update comment.
* mips-opc.c (mips_builtin_opcodes): Likewise. Mark coprocessor
instructions for IOCT as appropriate.
* mips-dis.c (print_insn_mips): Replace OPCODE_IS_MEMBER with
opcode_is_member.
* configure.in: Substitute NO_WMISSING_FIELD_INITIALIZERS with
the result of a check for the -Wno-missing-field-initializers
GCC option.
* Makefile.am (NO_WMISSING_FIELD_INITIALIZERS): New variable.
(mips-opc.lo): Pass $(NO_WMISSING_FIELD_INITIALIZERS) to
compilation.
(mips16-opc.lo): Likewise.
(micromips-opc.lo): Likewise.
* aclocal.m4: Regenerate.
* configure: Regenerate.
* Makefile.in: Regenerate.
gas/
* config/tc-mips.c (NO_ISA_COP, COP_INSN): Remove macros.
(is_opcode_valid): Remove coprocessor instruction exclusions.
Replace OPCODE_IS_MEMBER with opcode_is_member.
(is_opcode_valid_16): Replace OPCODE_IS_MEMBER with
opcode_is_member.
(macro): Remove coprocessor instruction exclusions.
|
|
* mips.h: Document microMIPS DSP ASE usage.
(MICROMIPSOP_MASK_DSPACC, MICROMIPSOP_SH_DSPACC): Update for
microMIPS DSP ASE support.
(MICROMIPSOP_MASK_DSPSFT, MICROMIPSOP_SH_DSPSFT): Likewise.
(MICROMIPSOP_MASK_SA3, MICROMIPSOP_SH_SA3): Likewise.
(MICROMIPSOP_MASK_SA4, MICROMIPSOP_SH_SA4): Likewise.
(MICROMIPSOP_MASK_IMM8, MICROMIPSOP_SH_IMM8): Likewise.
(MICROMIPSOP_MASK_IMM10, MICROMIPSOP_SH_IMM10): Likewise.
(MICROMIPSOP_MASK_WRDSP, MICROMIPSOP_SH_WRDSP): Likewise.
(MICROMIPSOP_MASK_BP, MICROMIPSOP_SH_BP): Likewise.
gas/
* config/tc-mips.c (macro_build) <'2'>: Handle microMIPS.
(macro) <M_BALIGN>: Update error handling.
(validate_micromips_insn) <'2', '3', '4', '5', '6'>: New cases.
<'7', '8', '0', '@', '^'>: Likewise.
(mips_ip) <'2', '3', '4', '5', '6', '7', '8'>: Handle microMIPS.
<'9'>: Fix formatting.
<'0', '@'>: Handle microMIPS.
<'^'>: New case.
gas/testsuite/
* gas/mips/micromips@mips32-dsp.d: New.
* gas/mips/micromips@mips32-dspr2.d: New.
* gas/mips/mips32-dsp.d: Remove -mips32r2.
* gas/mips/mips32-dspr2.d: Likewise.
* gas/mips/mips.exp: (mips_create_arch): Use -mips64r2
for micromips. Use run_dump_test_arches to run dsp tests.
opcodes/
* micromips-opc.c (WR_a, RD_a, MOD_a): New macros.
(DSP_VOLA): Likewise.
(D32, D33): Likewise.
(micromips_opcodes): Add DSP ASE instructions.
* micromips-dis.c (print_insn_micromips) <'2', '3'>: New cases.
<'4', '5', '6', '7', '8', '0', '^', '@'>: Likewise.
|
|
* configure.in: Add check that sysdep.h has been included before
any system header files.
* configure: Regenerate.
* config.in: Regenerate.
* sysdep.h: Generate an error if included before config.h.
* alpha-opc.c: Include sysdep.h before any other header file.
* alpha-dis.c: Likewise.
* avr-dis.c: Likewise.
* cgen-opc.c: Likewise.
* cr16-dis.c: Likewise.
* cris-dis.c: Likewise.
* crx-dis.c: Likewise.
* d10v-dis.c: Likewise.
* d10v-opc.c: Likewise.
* d30v-dis.c: Likewise.
* d30v-opc.c: Likewise.
* h8500-dis.c: Likewise.
* i370-dis.c: Likewise.
* i370-opc.c: Likewise.
* m10200-dis.c: Likewise.
* m10300-dis.c: Likewise.
* micromips-opc.c: Likewise.
* mips-opc.c: Likewise.
* mips61-opc.c: Likewise.
* moxie-dis.c: Likewise.
* or32-opc.c: Likewise.
* pj-dis.c: Likewise.
* ppc-dis.c: Likewise.
* ppc-opc.c: Likewise.
* s390-dis.c: Likewise.
* sh-dis.c: Likewise.
* sh64-dis.c: Likewise.
* sparc-dis.c: Likewise.
* sparc-opc.c: Likewise.
* spu-dis.c: Likewise.
* tic30-dis.c: Likewise.
* tic54x-dis.c: Likewise.
* tic80-dis.c: Likewise.
* tic80-opc.c: Likewise.
* tilegx-dis.c: Likewise.
* tilepro-dis.c: Likewise.
* v850-dis.c: Likewise.
* v850-opc.c: Likewise.
* vax-dis.c: Likewise.
* w65-dis.c: Likewise.
* xgate-dis.c: Likewise.
* xtensa-dis.c: Likewise.
* rl78-decode.opc: Likewise.
* rl78-decode.c: Regenerate.
* rx-decode.opc: Likewise.
* rx-decode.c: Regenerate.
* configure.in: Add check that sysdep.h has been included before
any system header files.
* configure: Regenerate.
* config.in: Regenerate.
* sysdep.h: Generate an error if included before config.h.
* configure.in: Add check that sysdep.h has been included before
any system header files.
* configure: Regenerate.
* config.in: Regenerate.
* aclocal.m4: Regenerate.
* bfd-in.h: Generate an error if included before config.h.
* sysdep.h: Likewise.
* bfd-in2.h: Regenerate.
* compress.c: Remove #include "config.h".
* plugin.c: Likewise.
* elf32-m68hc1x.c: Include sysdep.h before alloca-conf.h.
* elf64-hppa.c: Likewise.
* som.c: Likewise.
* xsymc.c: Likewise.
* configure.in: Add check that sysdep.h has been included before
any system header files.
* configure: Regenerate.
* config.in: Regenerate.
* configure.in: Add check that sysdep.h has been included before
any system header files.
* configure: Regenerate.
* config.in: Regenerate.
* aclocal.m4: Regenerate.
* Makefile.am: Use wrappers around C files generated by flex.
* Makefile.in: Regenerate.
* doc/Makefile.in: Regenerate.
* itbl-lex-wrapper.c: New file.
* config/bfin-lex-wrapper.c: New file.
* cgen.c: Include as.h before setjmp.h.
* config/tc-dlx.c: Include as.h before any other header.
* config/tc-h8300.c: Likewise.
* config/tc-lm32.c: Likewise.
* config/tc-mep.c: Likewise.
* config/tc-microblaze.c: Likewise.
* config/tc-mmix.c: Likewise.
* config/tc-msp430.c: Likewise.
* config/tc-or32.c: Likewise.
* config/tc-tic4x.c: Likewise.
* config/tc-tic54x.c: Likewise.
* config/tc-xtensa.c: Likewise.
* configure.in: Add check that sysdep.h has been included before
any system header files.
* configure: Regenerate.
* config.in: Regenerate.
* unwind-ia64.h: Include config.h.
|
|
for "alnv.ps".
|
|
* config/tc-mips.c (mips_set_options): Add ase_mcu.
(mips_opts): Initialise ase_mcu to -1.
(ISA_SUPPORTS_MCU_ASE): New macro.
(MIPS_CPU_ASE_MCU): Likewise.
(is_opcode_valid): Handle MCU.
(macro_build, macro): Likewise.
(validate_mips_insn, validate_micromips_insn): Likewise.
(mips_ip): Likewise.
(options): Add OPTION_MCU and OPTION_NO_MCU.
(md_longopts): Add mmcu and mno-mcu.
(md_parse_option): Handle OPTION_MCU and OPTION_NO_MCU.
(mips_after_parse_args): Handle MCU.
(s_mipsset): Likewise.
(md_show_usage): Handle MCU options.
* doc/as.texinfo: Document -mmcu and -mno-mcu options.
* doc/c-mips.texi: Likewise, and document ".set mcu" and
".set nomcu" directives.
gas/testsuite/
* gas/mips/micromips@mcu.d: New test.
* gas/mips/mcu.d: Likewise.
* gas/mips/mcu.s: New test source.
* gas/mips/mips.exp: Run the new tests.
include/opcode/
* mips.h (OP_MASK_3BITPOS, OP_SH_3BITPOS): New macros.
(OP_MASK_OFFSET12, OP_SH_OFFSET12): Redefine.
(INSN_ASE_MASK): Add the MCU bit.
(INSN_MCU): New macro.
(M_ACLR_AB, M_ACLR_OB, M_ASET_AB, M_ASET_OB): New enum values.
(MICROMIPSOP_MASK_3BITPOS, MICROMIPSOP_SH_3BITPOS): New macros.
opcodes/
* mips-dis.c (mips_arch_choices): Enable MCU for "mips32r2"
and "mips64r2".
(print_insn_args, print_insn_micromips): Handle MCU.
* micromips-opc.c (MC): New macro.
(micromips_opcodes): Add "aclr", "aset" and "iret".
* mips-opc.c (MC): New macro.
(mips_builtin_opcodes): Add "aclr", "aset" and "iret".
|
|
* mips.h (INSN_WRITE_GPR_S, INSN2_WRITE_GPR_MB): New macros.
(INSN2_READ_GPR_MC, INSN2_READ_GPR_ME): Likewise.
(INSN2_WRITE_GPR_MF, INSN2_READ_GPR_MG): Likewise.
(INSN2_READ_GPR_MJ, INSN2_WRITE_GPR_MJ): Likewise.
(INSN2_READ_GPR_MP, INSN2_WRITE_GPR_MP): Likewise.
(INSN2_READ_GPR_MQ, INSN2_WRITE_GPR_MHI): Likewise.
(INSN2_READ_GPR_MMN): Likewise.
(INSN2_READ_FPR_D): Change the bit used.
(INSN2_MOD_GPR_MD, INSN2_MOD_GPR_MF): Likewise.
(INSN2_MOD_SP, INSN2_READ_GPR_31, INSN2_READ_GP): Likewise.
(INSN2_READ_PC, INSN2_UNCOND_BRANCH): Likewise.
(INSN2_COND_BRANCH): Likewise.
(INSN2_WRITE_GPR_S, INSN2_MOD_GPR_MB): Remove macros.
(INSN2_MOD_GPR_MC, INSN2_MOD_GPR_ME, INSN2_MOD_GPR_MG): Likewise.
(INSN2_MOD_GPR_MJ, INSN2_MOD_GPR_MP, INSN2_MOD_GPR_MQ): Likewise.
(INSN2_MOD_GPR_MHI, INSN2_MOD_GPR_MM): Likewise.
(INSN2_MOD_GPR_MN): Likewise.
gas/
* config/tc-mips.c (gpr_mod_mask): Remove INSN2_MOD_GPR_MB,
INSN2_MOD_GPR_MC, INSN2_MOD_GPR_ME, INSN2_MOD_GPR_MG,
INSN2_MOD_GPR_MHI, INSN2_MOD_GPR_MJ, INSN2_MOD_GPR_MM,
INSN2_MOD_GPR_MN, INSN2_MOD_GPR_MP and INSN2_MOD_GPR_MQ opcode
register use checks.
(gpr_read_mask): Add INSN2_READ_GPR_MC, INSN2_READ_GPR_ME
INSN2_READ_GPR_MG, INSN2_READ_GPR_MJ, INSN2_READ_GPR_MMN,
INSN2_READ_GPR_MP and INSN2_READ_GPR_MQ opcode register use
checks.
(gpr_write_mask): Replace INSN2_WRITE_GPR_S opcode register
use flag with INSN_WRITE_GPR_S. Add INSN2_WRITE_GPR_MB,
INSN2_WRITE_GPR_MHI, INSN2_WRITE_GPR_MJ and INSN2_WRITE_GPR_MP
opcode register use checks.
(can_swap_branch_p): Enable microMIPS branch swapping.
(append_insn): Likewise.
gas/testsuite/
* gas/mips/micromips.d: Update according to changes to enable
microMIPS branch swapping.
* gas/mips/micromips-trap.d: Likewise.
* gas/mips/micromips@jal-svr4pic.d: Likewise.
* gas/mips/micromips@loc-swap.d: Likewise.
* gas/mips/micromips@loc-swap-dis.d: Likewise.
opcodes/
* micromips-opc.c (MOD_mb, MOD_mc, MOD_md): Remove macros.
(MOD_me, MOD_mf, MOD_mg, MOD_mhi, MOD_mj, MOD_ml): Likewise.
(MOD_mm, MOD_mn, MOD_mp, MOD_mq, MOD_sp): Likewise.
(WR_mb, RD_mc, RD_md, WR_md, RD_me, RD_mf, WR_mf): New macros.
(RD_mg, WR_mhi, RD_mj, WR_mj, RD_ml, RD_mmn): Likewise.
(RD_mp, WR_mp, RD_mq, RD_sp, WR_sp): Likewise.
(WR_s): Update macro.
(micromips_opcodes): Update register use flags of: "addiu",
"addiupc", "addiur1sp", "addiur2", "addius5", "addiusp", "addu",
"and", "andi", "beq", "beqz", "bne", "bnez", "di", "ei", "j",
"jalr", "jalrs", "jr", "jraddiusp", "jrc", "lbu", "lhu", "li",
"lui", "lw", "lwm", "mfhi", "mflo", "move", "movep", "not",
"nor", "or", "ori", "sb", "sh", "sll", "srl", "subu", "sw",
"swm" and "xor" instructions.
|
|
|
|
2011-02-25 Chao-ying Fu <fu@mips.com>
Ilie Garbacea <ilie@mips.com>
Maciej W. Rozycki <macro@codesourcery.com>
Joseph Myers <joseph@codesourcery.com>
Catherine Moore <clm@codesourcery.com>
Richard Sandiford <rdsandiford@googlemail.com>
* archures.c (bfd_mach_mips_micromips): New macro.
* cpu-mips.c (I_micromips): New enum value.
(arch_info_struct): Add bfd_mach_mips_micromips.
* elfxx-mips.h (_bfd_mips_elf_is_target_special_symbol): New
prototype.
(_bfd_mips_elf_relax_section): Likewise.
(_bfd_mips16_elf_reloc_unshuffle): Rename to...
(_bfd_mips_elf_reloc_unshuffle): ... this. Handle microMIPS
ASE.
(_bfd_mips16_elf_reloc_shuffle): Rename to...
(_bfd_mips_elf_reloc_shuffle): ... this. Handle microMIPS ASE.
(gprel16_reloc_p): Handle microMIPS ASE.
(literal_reloc_p): New function.
* elf32-mips.c (elf_micromips_howto_table_rel): New variable.
(_bfd_mips_elf32_gprel16_reloc): Handle microMIPS ASE.
(mips16_gprel_reloc): Update for _bfd_mips_elf_reloc_unshuffle
and _bfd_mips_elf_reloc_shuffle changes.
(mips_elf_gprel32_reloc): Update comment.
(micromips_reloc_map): New variable.
(bfd_elf32_bfd_reloc_type_lookup): Handle microMIPS ASE.
(mips_elf32_rtype_to_howto): Likewise.
(mips_info_to_howto_rel): Likewise.
(bfd_elf32_bfd_is_target_special_symbol): Define.
(bfd_elf32_bfd_relax_section): Likewise.
* elf64-mips.c (micromips_elf64_howto_table_rel): New variable.
(micromips_elf64_howto_table_rela): Likewise.
(mips16_gprel_reloc): Update for _bfd_mips_elf_reloc_unshuffle
and _bfd_mips_elf_reloc_shuffle changes.
(micromips_reloc_map): Likewise.
(bfd_elf64_bfd_reloc_type_lookup): Handle microMIPS ASE.
(bfd_elf64_bfd_reloc_name_lookup): Likewise.
(mips_elf64_rtype_to_howto): Likewise.
(bfd_elf64_bfd_is_target_special_symbol): Define.
* elfn32-mips.c (elf_micromips_howto_table_rel): New variable.
(elf_micromips_howto_table_rela): Likewise.
(mips16_gprel_reloc): Update for _bfd_mips_elf_reloc_unshuffle
and _bfd_mips_elf_reloc_shuffle changes.
(micromips_reloc_map): Likewise.
(bfd_elf32_bfd_reloc_type_lookup): Handle microMIPS ASE.
(bfd_elf32_bfd_reloc_name_lookup): Likewise.
(mips_elf_n32_rtype_to_howto): Likewise.
(bfd_elf32_bfd_is_target_special_symbol): Define.
* elfxx-mips.c (LA25_LUI_MICROMIPS_1): New macro.
(LA25_LUI_MICROMIPS_2): Likewise.
(LA25_J_MICROMIPS_1, LA25_J_MICROMIPS_2): Likewise.
(LA25_ADDIU_MICROMIPS_1, LA25_ADDIU_MICROMIPS_2): Likewise.
(TLS_RELOC_P): Handle microMIPS ASE.
(mips_elf_create_stub_symbol): Adjust value of stub symbol if
target is a microMIPS function.
(micromips_reloc_p): New function.
(micromips_reloc_shuffle_p): Likewise.
(got16_reloc_p, call16_reloc_p): Handle microMIPS ASE.
(got_disp_reloc_p, got_page_reloc_p): New functions.
(got_ofst_reloc_p): Likewise.
(got_hi16_reloc_p, got_lo16_reloc_p): Likewise.
(call_hi16_reloc_p, call_lo16_reloc_p): Likewise.
(hi16_reloc_p, lo16_reloc_p, jal_reloc_p): Handle microMIPS ASE.
(micromips_branch_reloc_p): New function.
(tls_gd_reloc_p, tls_ldm_reloc_p): Likewise.
(tls_gottprel_reloc_p): Likewise.
(_bfd_mips16_elf_reloc_unshuffle): Rename to...
(_bfd_mips_elf_reloc_unshuffle): ... this. Handle microMIPS
ASE.
(_bfd_mips16_elf_reloc_shuffle): Rename to...
(_bfd_mips_elf_reloc_shuffle): ... this. Handle microMIPS ASE.
(_bfd_mips_elf_lo16_reloc): Handle microMIPS ASE.
(mips_tls_got_index, mips_elf_got_page): Likewise.
(mips_elf_create_local_got_entry): Likewise.
(mips_elf_relocation_needs_la25_stub): Likewise.
(mips_elf_calculate_relocation): Likewise.
(mips_elf_perform_relocation): Likewise.
(_bfd_mips_elf_symbol_processing): Likewise.
(_bfd_mips_elf_add_symbol_hook): Likewise.
(_bfd_mips_elf_link_output_symbol_hook): Likewise.
(mips_elf_add_lo16_rel_addend): Likewise.
(_bfd_mips_elf_check_relocs): Likewise.
(mips_elf_adjust_addend): Likewise.
(_bfd_mips_elf_relocate_section): Likewise.
(mips_elf_create_la25_stub): Likewise.
(_bfd_mips_vxworks_finish_dynamic_symbol): Likewise.
(_bfd_mips_elf_gc_sweep_hook): Likewise.
(_bfd_mips_elf_is_target_special_symbol): New function.
(mips_elf_relax_delete_bytes): Likewise.
(opcode_descriptor): New structure.
(RA): New macro.
(OP32_SREG, OP32_TREG, OP16_VALID_REG): Likewise.
(b_insns_32, bc_insn_32, bz_insn_32, bzal_insn_32): New variables.
(beq_insn_32): Likewise.
(b_insn_16, bz_insn_16): New variables.
(BZC32_REG_FIELD): New macro.
(bz_rs_insns_32, bz_rt_insns_32): New variables.
(bzc_insns_32, bz_insns_16):Likewise.
(BZ16_REG, BZ16_REG_FIELD): New macros.
(jal_insn_32_bd16, jal_insn_32_bd32): New variables.
(jal_x_insn_32_bd32): Likewise.
(j_insn_32, jalr_insn_32): Likewise.
(ds_insns_32_bd16, ds_insns_32_bd32): Likewise.
(jalr_insn_16_bd16, jalr_insn_16_bd32, jr_insn_16): Likewise.
(JR16_REG): New macro.
(ds_insns_16_bd16): New variable.
(lui_insn): Likewise.
(addiu_insn, addiupc_insn): Likewise.
(ADDIUPC_REG_FIELD): New macro.
(MOVE32_RD, MOVE32_RS): Likewise.
(MOVE16_RD_FIELD, MOVE16_RS_FIELD): Likewise.
(move_insns_32, move_insns_16): New variables.
(nop_insn_32, nop_insn_16): Likewise.
(MATCH): New macro.
(find_match): New function.
(check_br16_dslot, check_br32_dslot): Likewise.
(check_br16, check_br32): Likewise.
(IS_BITSIZE): New macro.
(check_4byte_branch): New function.
(_bfd_mips_elf_relax_section): Likewise.
(_bfd_mips_elf_merge_private_bfd_data): Disallow linking MIPS16
and microMIPS modules together.
(_bfd_mips_elf_print_private_bfd_data): Handle microMIPS ASE.
* reloc.c (BFD_RELOC_MICROMIPS_7_PCREL_S1): New relocation.
(BFD_RELOC_MICROMIPS_10_PCREL_S1): Likewise.
(BFD_RELOC_MICROMIPS_16_PCREL_S1): Likewise.
(BFD_RELOC_MICROMIPS_GPREL16): Likewise.
(BFD_RELOC_MICROMIPS_JMP, BFD_RELOC_MICROMIPS_HI16): Likewise.
(BFD_RELOC_MICROMIPS_HI16_S): Likewise.
(BFD_RELOC_MICROMIPS_LO16): Likewise.
(BFD_RELOC_MICROMIPS_LITERAL): Likewise.
(BFD_RELOC_MICROMIPS_GOT16): Likewise.
(BFD_RELOC_MICROMIPS_CALL16): Likewise.
(BFD_RELOC_MICROMIPS_GOT_HI16): Likewise.
(BFD_RELOC_MICROMIPS_GOT_LO16): Likewise.
(BFD_RELOC_MICROMIPS_CALL_HI16): Likewise.
(BFD_RELOC_MICROMIPS_CALL_LO16): Likewise.
(BFD_RELOC_MICROMIPS_SUB): Likewise.
(BFD_RELOC_MICROMIPS_GOT_PAGE): Likewise.
(BFD_RELOC_MICROMIPS_GOT_OFST): Likewise.
(BFD_RELOC_MICROMIPS_GOT_DISP): Likewise.
(BFD_RELOC_MICROMIPS_HIGHEST): Likewise.
(BFD_RELOC_MICROMIPS_HIGHER): Likewise.
(BFD_RELOC_MICROMIPS_SCN_DISP): Likewise.
(BFD_RELOC_MICROMIPS_JALR): Likewise.
(BFD_RELOC_MICROMIPS_TLS_GD): Likewise.
(BFD_RELOC_MICROMIPS_TLS_LDM): Likewise.
(BFD_RELOC_MICROMIPS_TLS_DTPREL_HI16): Likewise.
(BFD_RELOC_MICROMIPS_TLS_DTPREL_LO16): Likewise.
(BFD_RELOC_MICROMIPS_TLS_GOTTPREL): Likewise.
(BFD_RELOC_MICROMIPS_TLS_TPREL_HI16): Likewise.
(BFD_RELOC_MICROMIPS_TLS_TPREL_LO16): Likewise.
* bfd-in2.h: Regenerate.
* libbfd.h: Regenerate.
binutils/
2011-02-25 Chao-ying Fu <fu@mips.com>
Maciej W. Rozycki <macro@codesourcery.com>
* readelf.c (get_machine_flags): Handle microMIPS ASE.
(get_mips_symbol_other): Likewise.
gas/
2011-02-25 Maciej W. Rozycki <macro@codesourcery.com>
Chao-ying Fu <fu@mips.com>
Richard Sandiford <rdsandiford@googlemail.com>
* config/tc-mips.h (mips_segment_info): Add one bit for
microMIPS.
(TC_LABEL_IS_LOCAL): New macro.
(mips_label_is_local): New prototype.
* config/tc-mips.c (S0, S7): New macros.
(emit_branch_likely_macro): New variable.
(mips_set_options): Add micromips.
(mips_opts): Initialise micromips to -1.
(file_ase_micromips): New variable.
(CPU_HAS_MICROMIPS): New macro.
(hilo_interlocks): Set for microMIPS too.
(gpr_interlocks): Likewise.
(cop_interlocks): Likewise.
(cop_mem_interlocks): Likewise.
(HAVE_CODE_COMPRESSION): New macro.
(micromips_op_hash): New variable.
(micromips_nop16_insn, micromips_nop32_insn): New variables.
(NOP_INSN): Handle microMIPS ASE.
(mips32_to_micromips_reg_b_map): New macro.
(mips32_to_micromips_reg_c_map): Likewise.
(mips32_to_micromips_reg_d_map): Likewise.
(mips32_to_micromips_reg_e_map): Likewise.
(mips32_to_micromips_reg_f_map): Likewise.
(mips32_to_micromips_reg_g_map): Likewise.
(mips32_to_micromips_reg_l_map): Likewise.
(mips32_to_micromips_reg_n_map): Likewise.
(mips32_to_micromips_reg_h_map): New variable.
(mips32_to_micromips_reg_m_map): Likewise.
(mips32_to_micromips_reg_q_map): Likewise.
(micromips_to_32_reg_h_map): New variable.
(micromips_to_32_reg_i_map): Likewise.
(micromips_to_32_reg_m_map): Likewise.
(micromips_to_32_reg_q_map): Likewise.
(micromips_to_32_reg_b_map): New macro.
(micromips_to_32_reg_c_map): Likewise.
(micromips_to_32_reg_d_map): Likewise.
(micromips_to_32_reg_e_map): Likewise.
(micromips_to_32_reg_f_map): Likewise.
(micromips_to_32_reg_g_map): Likewise.
(micromips_to_32_reg_l_map): Likewise.
(micromips_to_32_reg_n_map): Likewise.
(micromips_imm_b_map, micromips_imm_c_map): New macros.
(RELAX_DELAY_SLOT_16BIT): New macro.
(RELAX_DELAY_SLOT_SIZE_FIRST): Likewise.
(RELAX_DELAY_SLOT_SIZE_SECOND): Likewise.
(RELAX_MICROMIPS_ENCODE, RELAX_MICROMIPS_P): New macros.
(RELAX_MICROMIPS_TYPE, RELAX_MICROMIPS_AT): Likewise.
(RELAX_MICROMIPS_U16BIT, RELAX_MICROMIPS_UNCOND): Likewise.
(RELAX_MICROMIPS_COMPACT, RELAX_MICROMIPS_LINK): Likewise.
(RELAX_MICROMIPS_RELAX32, RELAX_MICROMIPS_TOOFAR16): Likewise.
(RELAX_MICROMIPS_MARK_TOOFAR16): Likewise.
(RELAX_MICROMIPS_CLEAR_TOOFAR16): Likewise.
(RELAX_MICROMIPS_TOOFAR32): Likewise.
(RELAX_MICROMIPS_MARK_TOOFAR32): Likewise.
(RELAX_MICROMIPS_CLEAR_TOOFAR32): Likewise.
(INSERT_OPERAND, EXTRACT_OPERAND): Handle microMIPS ASE.
(mips_macro_warning): Add delay_slot_16bit_p, delay_slot_32bit_p,
fsize and insns.
(mips_mark_labels): New function.
(mips16_small, mips16_ext): Remove variables, replacing with...
(forced_insn_size): ... this.
(append_insn, mips16_ip): Update accordingly.
(micromips_insn_length): New function.
(insn_length): Return the length of microMIPS instructions.
(mips_record_mips16_mode): Rename to...
(mips_record_compressed_mode): ... this. Handle microMIPS ASE.
(install_insn): Handle microMIPS ASE.
(reglist_lookup): New function.
(is_size_valid, is_delay_slot_valid): Likewise.
(md_begin): Handle microMIPS ASE.
(md_assemble): Likewise. Update for append_insn interface change.
(micromips_reloc_p): New function.
(got16_reloc_p): Handle microMIPS ASE.
(hi16_reloc_p): Likewise.
(lo16_reloc_p): Likewise.
(jmp_reloc_p): New function.
(jalr_reloc_p): Likewise.
(matching_lo_reloc): Handle microMIPS ASE.
(insn_uses_reg, reg_needs_delay): Likewise.
(mips_move_labels): Likewise.
(mips16_mark_labels): Rename to...
(mips_compressed_mark_labels): ... this. Handle microMIPS ASE.
(gpr_mod_mask): New function.
(gpr_read_mask, gpr_write_mask): Handle microMIPS ASE.
(fpr_read_mask, fpr_write_mask): Likewise.
(insns_between, nops_for_vr4130, nops_for_insn): Likewise.
(fix_loongson2f_nop, fix_loongson2f_jump): Likewise.
(MICROMIPS_LABEL_CHAR): New macro.
(micromips_target_label, micromips_target_name): New variables.
(micromips_label_name, micromips_label_expr): New functions.
(micromips_label_inc, micromips_add_label): Likewise.
(mips_label_is_local): Likewise.
(micromips_map_reloc): Likewise.
(can_swap_branch_p): Handle microMIPS ASE.
(append_insn): Add expansionp argument. Handle microMIPS ASE.
(start_noreorder, end_noreorder): Handle microMIPS ASE.
(macro_start, macro_warning, macro_end): Likewise.
(brk_fmt, cop12_fmt, jalr_fmt, lui_fmt): New variables.
(mem12_fmt, mfhl_fmt, shft_fmt, trap_fmt): Likewise.
(BRK_FMT, COP12_FMT, JALR_FMT, LUI_FMT): New macros.
(MEM12_FMT, MFHL_FMT, SHFT_FMT, TRAP_FMT): Likewise.
(macro_build): Handle microMIPS ASE. Update for append_insn
interface change.
(mips16_macro_build): Update for append_insn interface change.
(macro_build_jalr): Handle microMIPS ASE.
(macro_build_lui): Likewise. Simplify.
(load_register): Handle microMIPS ASE.
(load_address): Likewise.
(move_register): Likewise.
(macro_build_branch_likely): New function.
(macro_build_branch_ccl): Likewise.
(macro_build_branch_rs): Likewise.
(macro_build_branch_rsrt): Likewise.
(macro): Handle microMIPS ASE.
(validate_micromips_insn): New function.
(expr_const_in_range): Likewise.
(mips_ip): Handle microMIPS ASE.
(options): Add OPTION_MICROMIPS and OPTION_NO_MICROMIPS.
(md_longopts): Add mmicromips and mno-micromips.
(md_parse_option): Handle OPTION_MICROMIPS and
OPTION_NO_MICROMIPS.
(mips_after_parse_args): Handle microMIPS ASE.
(md_pcrel_from): Handle microMIPS relocations.
(mips_force_relocation): Likewise.
(md_apply_fix): Likewise.
(mips_align): Handle microMIPS ASE.
(s_mipsset): Likewise.
(s_cpload, s_cpsetup, s_cpreturn): Use relocation wrappers.
(s_dtprel_internal): Likewise.
(s_gpword, s_gpdword): Likewise.
(s_insn): Handle microMIPS ASE.
(s_mips_stab): Likewise.
(relaxed_micromips_32bit_branch_length): New function.
(relaxed_micromips_16bit_branch_length): New function.
(md_estimate_size_before_relax): Handle microMIPS ASE.
(mips_fix_adjustable): Likewise.
(tc_gen_reloc): Handle microMIPS relocations.
(mips_relax_frag): Handle microMIPS ASE.
(md_convert_frag): Likewise.
(mips_frob_file_after_relocs): Likewise.
(mips_elf_final_processing): Likewise.
(mips_nop_opcode): Likewise.
(mips_handle_align): Likewise.
(md_show_usage): Handle microMIPS options.
* symbols.c (TC_LABEL_IS_LOCAL): New macro.
(S_IS_LOCAL): Add a TC_LABEL_IS_LOCAL check.
* doc/as.texinfo (Target MIPS options): Add -mmicromips and
-mno-micromips.
(-mmicromips, -mno-micromips): New options.
* doc/c-mips.texi (-mmicromips, -mno-micromips): New options.
(MIPS ISA): Document .set micromips and .set nomicromips.
(MIPS insn): Update for microMIPS support.
gas/testsuite/
2011-02-25 Maciej W. Rozycki <macro@codesourcery.com>
Chao-ying Fu <fu@mips.com>
Richard Sandiford <rdsandiford@googlemail.com>
* gas/mips/micromips.d: New test.
* gas/mips/micromips-branch-delay.d: Likewise.
* gas/mips/micromips-branch-relax.d: Likewise.
* gas/mips/micromips-branch-relax-pic.d: Likewise.
* gas/mips/micromips-size-1.d: Likewise.
* gas/mips/micromips-trap.d: Likewise.
* gas/mips/micromips.l: New stderr output.
* gas/mips/micromips-branch-delay.l: Likewise.
* gas/mips/micromips-branch-relax.l: Likewise.
* gas/mips/micromips-branch-relax-pic.l: Likewise.
* gas/mips/micromips-size-0.l: New list test.
* gas/mips/micromips-size-1.l: New stderr output.
* gas/mips/micromips.s: New test source.
* gas/mips/micromips-branch-delay.s: Likewise.
* gas/mips/micromips-branch-relax.s: Likewise.
* gas/mips/micromips-size-0.s: Likewise.
* gas/mips/micromips-size-1.s: Likewise.
* gas/mips/mips.exp: Run the new tests.
* gas/mips/dli.s: Use .p2align.
* gas/mips/elf_ase_micromips.d: New test.
* gas/mips/elf_ase_micromips-2.d: Likewise.
* gas/mips/micromips@abs.d: Likewise.
* gas/mips/micromips@add.d: Likewise.
* gas/mips/micromips@alnv_ps-swap.d: Likewise.
* gas/mips/micromips@and.d: Likewise.
* gas/mips/micromips@beq.d: Likewise.
* gas/mips/micromips@bge.d: Likewise.
* gas/mips/micromips@bgeu.d: Likewise.
* gas/mips/micromips@blt.d: Likewise.
* gas/mips/micromips@bltu.d: Likewise.
* gas/mips/micromips@branch-likely.d: Likewise.
* gas/mips/micromips@branch-misc-1.d: Likewise.
* gas/mips/micromips@branch-misc-2-64.d: Likewise.
* gas/mips/micromips@branch-misc-2.d: Likewise.
* gas/mips/micromips@branch-misc-2pic-64.d: Likewise.
* gas/mips/micromips@branch-misc-2pic.d: Likewise.
* gas/mips/micromips@branch-misc-4-64.d: Likewise.
* gas/mips/micromips@branch-misc-4.d: Likewise.
* gas/mips/micromips@branch-self.d: Likewise.
* gas/mips/micromips@cache.d: Likewise.
* gas/mips/micromips@daddi.d: Likewise.
* gas/mips/micromips@dli.d: Likewise.
* gas/mips/micromips@elf-jal.d: Likewise.
* gas/mips/micromips@elf-rel2.d: Likewise.
* gas/mips/micromips@elfel-rel2.d: Likewise.
* gas/mips/micromips@elf-rel4.d: Likewise.
* gas/mips/micromips@jal-svr4pic.d: Likewise.
* gas/mips/micromips@jal-svr4pic-noreorder.d: Likewise.
* gas/mips/micromips@lb-svr4pic-ilocks.d: Likewise.
* gas/mips/micromips@li.d: Likewise.
* gas/mips/micromips@loc-swap-dis.d: Likewise.
* gas/mips/micromips@loc-swap.d: Likewise.
* gas/mips/micromips@mips1-fp.d: Likewise.
* gas/mips/micromips@mips32-cp2.d: Likewise.
* gas/mips/micromips@mips32-imm.d: Likewise.
* gas/mips/micromips@mips32-sf32.d: Likewise.
* gas/mips/micromips@mips32.d: Likewise.
* gas/mips/micromips@mips32r2-cp2.d: Likewise.
* gas/mips/micromips@mips32r2-fp32.d: Likewise.
* gas/mips/micromips@mips32r2-sync.d: Likewise.
* gas/mips/micromips@mips32r2.d: Likewise.
* gas/mips/micromips@mips4-branch-likely.d: Likewise.
* gas/mips/micromips@mips4-fp.d: Likewise.
* gas/mips/micromips@mips4.d: Likewise.
* gas/mips/micromips@mips5.d: Likewise.
* gas/mips/micromips@mips64-cp2.d: Likewise.
* gas/mips/micromips@mips64.d: Likewise.
* gas/mips/micromips@mips64r2.d: Likewise.
* gas/mips/micromips@pref.d: Likewise.
* gas/mips/micromips@relax-at.d: Likewise.
* gas/mips/micromips@relax.d: Likewise.
* gas/mips/micromips@rol-hw.d: Likewise.
* gas/mips/micromips@uld2-eb.d: Likewise.
* gas/mips/micromips@uld2-el.d: Likewise.
* gas/mips/micromips@ulh2-eb.d: Likewise.
* gas/mips/micromips@ulh2-el.d: Likewise.
* gas/mips/micromips@ulw2-eb-ilocks.d: Likewise.
* gas/mips/micromips@ulw2-el-ilocks.d: Likewise.
* gas/mips/cache.d: Likewise.
* gas/mips/daddi.d: Likewise.
* gas/mips/mips32-imm.d: Likewise.
* gas/mips/pref.d: Likewise.
* gas/mips/elf-rel27.d: Handle microMIPS ASE.
* gas/mips/l_d.d: Likewise.
* gas/mips/l_d-n32.d: Likewise.
* gas/mips/l_d-n64.d: Likewise.
* gas/mips/ld.d: Likewise.
* gas/mips/ld-n32.d: Likewise.
* gas/mips/ld-n64.d: Likewise.
* gas/mips/s_d.d: Likewise.
* gas/mips/s_d-n32.d: Likewise.
* gas/mips/s_d-n64.d: Likewise.
* gas/mips/sd.d: Likewise.
* gas/mips/sd-n32.d: Likewise.
* gas/mips/sd-n64.d: Likewise.
* gas/mips/mips32.d: Update immediates.
* gas/mips/micromips@mips32-cp2.s: New test source.
* gas/mips/micromips@mips32-imm.s: Likewise.
* gas/mips/micromips@mips32r2-cp2.s: Likewise.
* gas/mips/micromips@mips64-cp2.s: Likewise.
* gas/mips/cache.s: Likewise.
* gas/mips/daddi.s: Likewise.
* gas/mips/mips32-imm.s: Likewise.
* gas/mips/elf-rel4.s: Handle microMIPS ASE.
* gas/mips/lb-pic.s: Likewise.
* gas/mips/ld.s: Likewise.
* gas/mips/mips32.s: Likewise.
* gas/mips/mips.exp: Add the micromips arch. Exclude mips16e
from micromips. Run mips32-imm.
* gas/mips/jal-mask-11.d: New test.
* gas/mips/jal-mask-12.d: Likewise.
* gas/mips/micromips@jal-mask-11.d: Likewise.
* gas/mips/jal-mask-1.s: Source for the new tests.
* gas/mips/jal-mask-21.d: New test.
* gas/mips/jal-mask-22.d: Likewise.
* gas/mips/micromips@jal-mask-12.d: Likewise.
* gas/mips/jal-mask-2.s: Source for the new tests.
* gas/mips/mips.exp: Run the new tests.
* gas/mips/mips16-e.d: Add --special-syms to `objdump'.
* gas/mips/tmips16-e.d: Likewise.
* gas/mips/mipsel16-e.d: Likewise.
* gas/mips/tmipsel16-e.d: Likewise.
* gas/mips/and.s: Adjust padding.
* gas/mips/beq.s: Likewise.
* gas/mips/bge.s: Likewise.
* gas/mips/bgeu.s: Likewise.
* gas/mips/blt.s: Likewise.
* gas/mips/bltu.s: Likewise.
* gas/mips/branch-misc-2.s: Likewise.
* gas/mips/jal.s: Likewise.
* gas/mips/li.s: Likewise.
* gas/mips/mips4.s: Likewise.
* gas/mips/mips4-fp.s: Likewise.
* gas/mips/relax.s: Likewise.
* gas/mips/and.d: Update accordingly.
* gas/mips/elf-jal.d: Likewise.
* gas/mips/jal.d: Likewise.
* gas/mips/li.d: Likewise.
* gas/mips/relax-at.d: Likewise.
* gas/mips/relax.d: Likewise.
include/elf/
2011-02-25 Chao-ying Fu <fu@mips.com>
Maciej W. Rozycki <macro@codesourcery.com>
* mips.h (R_MICROMIPS_min): New relocations.
(R_MICROMIPS_26_S1): Likewise.
(R_MICROMIPS_HI16, R_MICROMIPS_LO16): Likewise.
(R_MICROMIPS_GPREL16, R_MICROMIPS_LITERAL): Likewise.
(R_MICROMIPS_GOT16, R_MICROMIPS_PC7_S1): Likewise.
(R_MICROMIPS_PC10_S1, R_MICROMIPS_PC16_S1): Likewise.
(R_MICROMIPS_CALL16, R_MICROMIPS_GOT_DISP): Likewise.
(R_MICROMIPS_GOT_PAGE, R_MICROMIPS_GOT_OFST): Likewise.
(R_MICROMIPS_GOT_HI16, R_MICROMIPS_GOT_LO16): Likewise.
(R_MICROMIPS_SUB, R_MICROMIPS_HIGHER): Likewise.
(R_MICROMIPS_HIGHEST, R_MICROMIPS_CALL_HI16): Likewise.
(R_MICROMIPS_CALL_LO16, R_MICROMIPS_SCN_DISP): Likewise.
(R_MICROMIPS_JALR, R_MICROMIPS_HI0_LO16): Likewise.
(R_MICROMIPS_TLS_GD, R_MICROMIPS_TLS_LDM): Likewise.
(R_MICROMIPS_TLS_DTPREL_HI, R_MICROMIPS_TLS_DTPREL_LO): Likewise.
(R_MICROMIPS_TLS_GOTTPREL): Likewise.
(R_MICROMIPS_TLS_TPREL_HI16): Likewise.
(R_MICROMIPS_TLS_TPREL_LO16): Likewise.
(R_MICROMIPS_GPREL7_S2, R_MICROMIPS_PC23_S2): Likewise.
(R_MICROMIPS_max): Likewise.
(EF_MIPS_ARCH_ASE_MICROMIPS): New macro.
(STO_MIPS_ISA, STO_MIPS_FLAGS): Likewise.
(ELF_ST_IS_MIPS_PLT, ELF_ST_SET_MIPS_PLT): Likewise.
(STO_MICROMIPS): Likewise.
(ELF_ST_IS_MICROMIPS, ELF_ST_SET_MICROMIPS): Likewise.
(ELF_ST_IS_COMPRESSED): Likewise.
(STO_MIPS_PLT, STO_MIPS_PIC): Rework.
(ELF_ST_IS_MIPS_PIC, ELF_ST_SET_MIPS_PIC): Likewise.
(STO_MIPS16, ELF_ST_IS_MIPS16, ELF_ST_SET_MIPS16): Likewise.
include/opcode/
2011-02-25 Chao-ying Fu <fu@mips.com>
Maciej W. Rozycki <macro@codesourcery.com>
* mips.h (OP_MASK_EXTLSB, OP_SH_EXTLSB): New macros.
(OP_MASK_STYPE, OP_SH_STYPE): Likewise.
(OP_MASK_CODE10, OP_SH_CODE10): Likewise.
(OP_MASK_TRAP, OP_SH_TRAP): Likewise.
(OP_MASK_OFFSET12, OP_SH_OFFSET12): Likewise.
(OP_MASK_OFFSET10, OP_SH_OFFSET10): Likewise.
(OP_MASK_RS3, OP_SH_RS3): Likewise.
(OP_MASK_MB, OP_SH_MB, OP_MASK_MC, OP_SH_MC): Likewise.
(OP_MASK_MD, OP_SH_MD, OP_MASK_ME, OP_SH_ME): Likewise.
(OP_MASK_MF, OP_SH_MF, OP_MASK_MG, OP_SH_MG): Likewise.
(OP_MASK_MJ, OP_SH_MJ, OP_MASK_ML, OP_SH_ML): Likewise.
(OP_MASK_MP, OP_SH_MP, OP_MASK_MQ, OP_SH_MQ): Likewise.
(OP_MASK_IMMA, OP_SH_IMMA, OP_MASK_IMMB, OP_SH_IMMB): Likewise.
(OP_MASK_IMMC, OP_SH_IMMC, OP_MASK_IMMF, OP_SH_IMMF): Likewise.
(OP_MASK_IMMG, OP_SH_IMMG, OP_MASK_IMMH, OP_SH_IMMH): Likewise.
(OP_MASK_IMMI, OP_SH_IMMI, OP_MASK_IMMJ, OP_SH_IMMJ): Likewise.
(OP_MASK_IMML, OP_SH_IMML, OP_MASK_IMMM, OP_SH_IMMM): Likewise.
(OP_MASK_IMMN, OP_SH_IMMN, OP_MASK_IMMO, OP_SH_IMMO): Likewise.
(OP_MASK_IMMP, OP_SH_IMMP, OP_MASK_IMMQ, OP_SH_IMMQ): Likewise.
(OP_MASK_IMMU, OP_SH_IMMU, OP_MASK_IMMW, OP_SH_IMMW): Likewise.
(OP_MASK_IMMX, OP_SH_IMMX, OP_MASK_IMMY, OP_SH_IMMY): Likewise.
(INSN_WRITE_GPR_S): New macro.
(INSN2_BRANCH_DELAY_16BIT, INSN2_BRANCH_DELAY_32BIT): Likewise.
(INSN2_READ_FPR_D): Likewise.
(INSN2_MOD_GPR_MB, INSN2_MOD_GPR_MC): Likewise.
(INSN2_MOD_GPR_MD, INSN2_MOD_GPR_ME): Likewise.
(INSN2_MOD_GPR_MF, INSN2_MOD_GPR_MG): Likewise.
(INSN2_MOD_GPR_MJ, INSN2_MOD_GPR_MP): Likewise.
(INSN2_MOD_GPR_MQ, INSN2_MOD_SP): Likewise.
(INSN2_READ_GPR_31, INSN2_READ_GP, INSN2_READ_PC): Likewise.
(INSN2_UNCOND_BRANCH, INSN2_COND_BRANCH): Likewise.
(INSN2_MOD_GPR_MHI, INSN2_MOD_GPR_MM, INSN2_MOD_GPR_MN): Likewise.
(CPU_MICROMIPS): New macro.
(M_BC1FL, M_BC1TL, M_BC2FL, M_BC2TL): New enum values.
(M_BEQL, M_BGEZ, M_BGEZL, M_BGEZALL, M_BGTZ, M_BGTZL): Likewise.
(M_BLEZ, M_BLEZL, M_BLTZ, M_BLTZL, M_BLTZALL, M_BNEL): Likewise.
(M_CACHE_OB, M_JALS_1, M_JALS_2, M_JALS_A): Likewise.
(M_LDC2_OB, M_LDL_OB, M_LDM_AB, M_LDM_OB): Likewise.
(M_LDP_AB, M_LDP_OB, M_LDR_OB, M_LL_OB, M_LLD_OB): Likewise.
(M_LWC2_OB, M_LWL_OB, M_LWM_AB, M_LWM_OB): Likewise.
(M_LWP_AB, M_LWP_OB, M_LWR_OB): Likewise.
(M_LWU_OB, M_PREF_OB, M_SC_OB, M_SCD_OB): Likewise.
(M_SDC2_OB, M_SDL_OB, M_SDM_AB, M_SDM_OB): Likewise.
(M_SDP_AB, M_SDP_OB, M_SDR_OB): Likewise.
(M_SWC2_OB, M_SWL_OB, M_SWM_AB, M_SWM_OB): Likewise.
(M_SWP_AB, M_SWP_OB, M_SWR_OB): Likewise.
(MICROMIPSOP_MASK_MAJOR, MICROMIPSOP_SH_MAJOR): New macros.
(MICROMIPSOP_MASK_IMMEDIATE, MICROMIPSOP_SH_IMMEDIATE): Likewise.
(MICROMIPSOP_MASK_DELTA, MICROMIPSOP_SH_DELTA): Likewise.
(MICROMIPSOP_MASK_CODE10, MICROMIPSOP_SH_CODE10): Likewise.
(MICROMIPSOP_MASK_TRAP, MICROMIPSOP_SH_TRAP): Likewise.
(MICROMIPSOP_MASK_SHAMT, MICROMIPSOP_SH_SHAMT): Likewise.
(MICROMIPSOP_MASK_TARGET, MICROMIPSOP_SH_TARGET): Likewise.
(MICROMIPSOP_MASK_EXTLSB, MICROMIPSOP_SH_EXTLSB): Likewise.
(MICROMIPSOP_MASK_EXTMSBD, MICROMIPSOP_SH_EXTMSBD): Likewise.
(MICROMIPSOP_MASK_INSMSB, MICROMIPSOP_SH_INSMSB): Likewise.
(MICROMIPSOP_MASK_CODE, MICROMIPSOP_SH_CODE): Likewise.
(MICROMIPSOP_MASK_CODE2, MICROMIPSOP_SH_CODE2): Likewise.
(MICROMIPSOP_MASK_CACHE, MICROMIPSOP_SH_CACHE): Likewise.
(MICROMIPSOP_MASK_SEL, MICROMIPSOP_SH_SEL): Likewise.
(MICROMIPSOP_MASK_OFFSET12, MICROMIPSOP_SH_OFFSET12): Likewise.
(MICROMIPSOP_MASK_3BITPOS, MICROMIPSOP_SH_3BITPOS): Likewise.
(MICROMIPSOP_MASK_STYPE, MICROMIPSOP_SH_STYPE): Likewise.
(MICROMIPSOP_MASK_OFFSET10, MICROMIPSOP_SH_OFFSET10): Likewise.
(MICROMIPSOP_MASK_RS, MICROMIPSOP_SH_RS): Likewise.
(MICROMIPSOP_MASK_RT, MICROMIPSOP_SH_RT): Likewise.
(MICROMIPSOP_MASK_RD, MICROMIPSOP_SH_RD): Likewise.
(MICROMIPSOP_MASK_FS, MICROMIPSOP_SH_FS): Likewise.
(MICROMIPSOP_MASK_FT, MICROMIPSOP_SH_FT): Likewise.
(MICROMIPSOP_MASK_FD, MICROMIPSOP_SH_FD): Likewise.
(MICROMIPSOP_MASK_FR, MICROMIPSOP_SH_FR): Likewise.
(MICROMIPSOP_MASK_RS3, MICROMIPSOP_SH_RS3): Likewise.
(MICROMIPSOP_MASK_PREFX, MICROMIPSOP_SH_PREFX): Likewise.
(MICROMIPSOP_MASK_BCC, MICROMIPSOP_SH_BCC): Likewise.
(MICROMIPSOP_MASK_CCC, MICROMIPSOP_SH_CCC): Likewise.
(MICROMIPSOP_MASK_COPZ, MICROMIPSOP_SH_COPZ): Likewise.
(MICROMIPSOP_MASK_MB, MICROMIPSOP_SH_MB): Likewise.
(MICROMIPSOP_MASK_MC, MICROMIPSOP_SH_MC): Likewise.
(MICROMIPSOP_MASK_MD, MICROMIPSOP_SH_MD): Likewise.
(MICROMIPSOP_MASK_ME, MICROMIPSOP_SH_ME): Likewise.
(MICROMIPSOP_MASK_MF, MICROMIPSOP_SH_MF): Likewise.
(MICROMIPSOP_MASK_MG, MICROMIPSOP_SH_MG): Likewise.
(MICROMIPSOP_MASK_MH, MICROMIPSOP_SH_MH): Likewise.
(MICROMIPSOP_MASK_MI, MICROMIPSOP_SH_MI): Likewise.
(MICROMIPSOP_MASK_MJ, MICROMIPSOP_SH_MJ): Likewise.
(MICROMIPSOP_MASK_ML, MICROMIPSOP_SH_ML): Likewise.
(MICROMIPSOP_MASK_MM, MICROMIPSOP_SH_MM): Likewise.
(MICROMIPSOP_MASK_MN, MICROMIPSOP_SH_MN): Likewise.
(MICROMIPSOP_MASK_MP, MICROMIPSOP_SH_MP): Likewise.
(MICROMIPSOP_MASK_MQ, MICROMIPSOP_SH_MQ): Likewise.
(MICROMIPSOP_MASK_IMMA, MICROMIPSOP_SH_IMMA): Likewise.
(MICROMIPSOP_MASK_IMMB, MICROMIPSOP_SH_IMMB): Likewise.
(MICROMIPSOP_MASK_IMMC, MICROMIPSOP_SH_IMMC): Likewise.
(MICROMIPSOP_MASK_IMMD, MICROMIPSOP_SH_IMMD): Likewise.
(MICROMIPSOP_MASK_IMME, MICROMIPSOP_SH_IMME): Likewise.
(MICROMIPSOP_MASK_IMMF, MICROMIPSOP_SH_IMMF): Likewise.
(MICROMIPSOP_MASK_IMMG, MICROMIPSOP_SH_IMMG): Likewise.
(MICROMIPSOP_MASK_IMMH, MICROMIPSOP_SH_IMMH): Likewise.
(MICROMIPSOP_MASK_IMMI, MICROMIPSOP_SH_IMMI): Likewise.
(MICROMIPSOP_MASK_IMMJ, MICROMIPSOP_SH_IMMJ): Likewise.
(MICROMIPSOP_MASK_IMML, MICROMIPSOP_SH_IMML): Likewise.
(MICROMIPSOP_MASK_IMMM, MICROMIPSOP_SH_IMMM): Likewise.
(MICROMIPSOP_MASK_IMMN, MICROMIPSOP_SH_IMMN): Likewise.
(MICROMIPSOP_MASK_IMMO, MICROMIPSOP_SH_IMMO): Likewise.
(MICROMIPSOP_MASK_IMMP, MICROMIPSOP_SH_IMMP): Likewise.
(MICROMIPSOP_MASK_IMMQ, MICROMIPSOP_SH_IMMQ): Likewise.
(MICROMIPSOP_MASK_IMMU, MICROMIPSOP_SH_IMMU): Likewise.
(MICROMIPSOP_MASK_IMMW, MICROMIPSOP_SH_IMMW): Likewise.
(MICROMIPSOP_MASK_IMMX, MICROMIPSOP_SH_IMMX): Likewise.
(MICROMIPSOP_MASK_IMMY, MICROMIPSOP_SH_IMMY): Likewise.
(MICROMIPSOP_MASK_CODE, MICROMIPSOP_SH_CODE): Likewise.
(MICROMIPSOP_MASK_CODE2, MICROMIPSOP_SH_CODE2): Likewise.
(MICROMIPSOP_MASK_CACHE, MICROMIPSOP_SH_CACHE): Likewise.
(MICROMIPSOP_MASK_CODE20, MICROMIPSOP_SH_CODE20): Likewise.
(MICROMIPSOP_MASK_PERFREG, MICROMIPSOP_SH_PERFREG): Likewise.
(MICROMIPSOP_MASK_CODE19, MICROMIPSOP_SH_CODE19): Likewise.
(MICROMIPSOP_MASK_ALN, MICROMIPSOP_SH_ALN): Likewise.
(MICROMIPSOP_MASK_VECBYTE, MICROMIPSOP_SH_VECBYTE): Likewise.
(MICROMIPSOP_MASK_VECALIGN, MICROMIPSOP_SH_VECALIGN): Likewise.
(MICROMIPSOP_MASK_DSPACC, MICROMIPSOP_SH_DSPACC): Likewise.
(MICROMIPSOP_MASK_DSPACC_S, MICROMIPSOP_SH_DSPACC_S): Likewise.
(MICROMIPSOP_MASK_DSPSFT, MICROMIPSOP_SH_DSPSFT): Likewise.
(MICROMIPSOP_MASK_DSPSFT_7, MICROMIPSOP_SH_DSPSFT_7): Likewise.
(MICROMIPSOP_MASK_SA3, MICROMIPSOP_SH_SA3): Likewise.
(MICROMIPSOP_MASK_SA4, MICROMIPSOP_SH_SA4): Likewise.
(MICROMIPSOP_MASK_IMM8, MICROMIPSOP_SH_IMM8): Likewise.
(MICROMIPSOP_MASK_IMM10, MICROMIPSOP_SH_IMM10): Likewise.
(MICROMIPSOP_MASK_WRDSP, MICROMIPSOP_SH_WRDSP): Likewise.
(MICROMIPSOP_MASK_RDDSP, MICROMIPSOP_SH_RDDSP): Likewise.
(MICROMIPSOP_MASK_BP, MICROMIPSOP_SH_BP): Likewise.
(MICROMIPSOP_MASK_MT_U, MICROMIPSOP_SH_MT_U): Likewise.
(MICROMIPSOP_MASK_MT_H, MICROMIPSOP_SH_MT_H): Likewise.
(MICROMIPSOP_MASK_MTACC_T, MICROMIPSOP_SH_MTACC_T): Likewise.
(MICROMIPSOP_MASK_MTACC_D, MICROMIPSOP_SH_MTACC_D): Likewise.
(MICROMIPSOP_MASK_BBITIND, MICROMIPSOP_SH_BBITIND): Likewise.
(MICROMIPSOP_MASK_CINSPOS, MICROMIPSOP_SH_CINSPOS): Likewise.
(MICROMIPSOP_MASK_CINSLM1, MICROMIPSOP_SH_CINSLM1): Likewise.
(MICROMIPSOP_MASK_SEQI, MICROMIPSOP_SH_SEQI): Likewise.
(micromips_opcodes): New declaration.
(bfd_micromips_num_opcodes): Likewise.
ld/testsuite/
2011-02-25 Catherine Moore <clm@codesourcery.com>
Chao-ying Fu <fu@mips.com>
Maciej W. Rozycki <macro@codesourcery.com>
* lib/ld-lib.exp (run_dump_test): Support distinct assembler
flags for the same source named multiple times.
* ld-mips-elf/jalx-1.s: New test source.
* ld-mips-elf/jalx-1.d: New test output.
* ld-mips-elf/jalx-1.ld: New test linker script.
* ld-mips-elf/jalx-2-main.s: New test source.
* ld-mips-elf/jalx-2-ex.s: Likewise.
* ld-mips-elf/jalx-2-printf.s: Likewise.
* ld-mips-elf/jalx-2.dd: New test output.
* ld-mips-elf/jalx-2.ld: New test linker script.
* ld-mips-elf/mips16-and-micromips.d: New test.
* ld-mips-elf/mips-elf.exp: Run the new tests
opcodes/
2011-02-25 Chao-ying Fu <fu@mips.com>
Maciej W. Rozycki <macro@codesourcery.com>
* micromips-opc.c: New file.
* mips-dis.c (micromips_to_32_reg_b_map): New array.
(micromips_to_32_reg_c_map, micromips_to_32_reg_d_map): Likewise.
(micromips_to_32_reg_e_map, micromips_to_32_reg_f_map): Likewise.
(micromips_to_32_reg_g_map, micromips_to_32_reg_l_map): Likewise.
(micromips_to_32_reg_q_map): Likewise.
(micromips_imm_b_map, micromips_imm_c_map): Likewise.
(micromips_ase): New variable.
(is_micromips): New function.
(set_default_mips_dis_options): Handle microMIPS ASE.
(print_insn_micromips): New function.
(is_compressed_mode_p): Likewise.
(_print_insn_mips): Handle microMIPS instructions.
* Makefile.am (CFILES): Add micromips-opc.c.
* configure.in (bfd_mips_arch): Add micromips-opc.lo.
* Makefile.in: Regenerate.
* configure: Regenerate.
* mips-dis.c (micromips_to_32_reg_h_map): New variable.
(micromips_to_32_reg_i_map): Likewise.
(micromips_to_32_reg_m_map): Likewise.
(micromips_to_32_reg_n_map): New macro.
|